Logo Museum Entrance
Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archives
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Colliery Guardian
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious

Title Prev Page Return to Index Next Page Title
/   \

The Installation and Moving Over of a Face Belt Conveyor

Training Manual No. 1

Chapter III

REPAIRING A BROKEN BELT

A   Top Belt

1. Locate the break.

2. Slacken off the Tension End by releasing the Sylvesters.

3. Pull the two ends into a suitable place to work.

4. Get all the tools required for repairing the belt to the place.

5. Prepare the belt ends as shown in Chapter II, Section A, page 26

6. Fix and fasten the couplings to each belt end as shown in Chapter II, Section B, page 27, making sure that the two ends mate.

7. Place the belt back on the structure.

8. Attach clamps securely to both ends of the belt, about three yards from each coupling, with clamp nuts on top (Figure 42).

9. Beneath the belt attach sylvester chain to one clamp and the sylvester to the other clamp. Operate the sylvester and draw the ends of the belt together until the coupling pins can be inserted. (Figure 43).

10. Insert coupling pins (secure where necessary with cotters), then remove the sylvester and clamps. Trim the four corners at the joint.

11. Tension the belt by pulling back the tension end with the sylvester.

12. Centralize the belt on the intermediate structure and on the return drum.

B   Bottom Belt

1. Locate the break.

2. Uncouple the top belt at the nearest point to the break and roll back on the intermediate structure, clear of both broken ends.

3. Slacken off Sylvesters at tension end.

4. Remove the intermediate structure to expose both broken ends of the belt.

5. Prepare the broken ends as shown in Chapter II, Section A, page 26.

6. Fit and fasten the couplings to both ends as shown in Chapter II, Section B.

7. Attach sylvester and clamps (Figure 44), and draw the belt ends together.

8. Insert coupling pins (secure where necessary with cotters), then remove the sylvester and clamps.

9. Replace intermediate structure in original position.

10. Unroll the top belt back on to the intermediate structure.

11. Attach clamps to the top belt, three yards from each hinge.

12. Beneath the belt attach sylvester chain to one clamp and the sylvester to the other clamp. Operate the sylvester and draw the ends of the belt together until the coupling pins can be inserted. (Figure 44).

13. Insert the coupling pins (where necessary secure with cotters).

14. Remove the sylvesters and clamps.

15. Tension the belt by operating sylvesters at the tension end.

16. Centralize the belt on the intermediate structure and on the return drum.

C   Broken Belt in Engine End or Tension End

1. Slacken off sylvesters at tension end.

2. Pull both broken ends away from the structure of drive head or tension end into a suitable place where ends can be prepared.

3. Prepare the ends as described in Chapter II, Section A, page 26.

4. Fix the fasteners to both ends of the broken belt as described in Chapter II, Section B, page 27.

5. Uncouple the top belt at the joint nearest to the break.

6. Thread this uncoupled piece round the driving drum or return drum (Figure 45).

7. Couple to the bottom belt.

8. Fix clamps 3 yards from each loose end of the belt, fix sylvester and draw the ends together as shown previously in Figure 44.

9. Couple the belt ends together.

10. Remove sylvester clamps.

11. Tension the belt by operating the sylvesters at the tension end.

12. Centralise the belt on the engine and on the return drum.

Note: Where Bristol couplings are used for belt jointing the belt ends must be drawn together before the joint can be made. Care must be taken that one of the ends does not get turned over or passed round props whilst they are being drawn together.

 

Prev Page Return to Top of Page Next Page

 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 31 Dec 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print