Museum
Friends of Durham Mining Museum
Events Calendar
Join our Friends!
Newsletter Contents
Items for sale
Items for Sale
e-Books
Photograph Gallery
Document Archive
Discussion Forums
What's new in the site

Mining History
Colliery Index
Colliery Maps
Educational Material
Bibliographye
Workers/Employee Lists
Notes for Family Historians

Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials

Links to other sites of interest
Industrial Heritage Days Out

View our Guestbook

Index to site



Mail: Webmaster


 
Protector Type GR6 (Garforth) LampsAppendix I to
 EI/G(70)5

INSTRUCTIONS FOR MAINTENANCE

1. Dismantling

Unlock the lamp by placing the plug of the magnetic lock on to a suitable unlocking magnet, when the lock bolt will be withdrawn and the filling hole cover can be swung to one side. The fuel vessel should now be removed by unscrewing it from the middle portion of the lamp. Next, pull down the slide wire which locks the top part of the lamp, and unscrew the bonnet. The gauzes, glass and washers can then be removed from the lamp for inspection and cleaning.

To remove a sintered ring, unscrew the milled thimble from the top of the Garforth chamber surrounding the wick, invert the middle portion of the lamp and gently tap the middle ring against the top of a bench, or some other flat surface. This will probably cause the sintered ring to move along the wick tube to a position from which it can be removed. If it is not possible to remove the sintered ring by the above method, it will be necessary to take off the glass plate by first unscrewing the three small screws holding it in place. The sintered ring then comes away with the glass plate.

2. Filling

Using N.C.B. Relighter Spirit No.1 pour the spirit slowly through the filler on the side of the fuel vessel. This operation should not be hurried as time must be allowed for the absorbent material inside the vessel to. become saturated. If filling is done too quickly, air locks may form and prevent the fuel from entering.

After filling, turn the vessel upside down, tilt so that surplus fuel flows out of the filling hole and leave for a few minutes in this position. Then shake gently to remove any excess. It is very important that no excess fuel is allowed to remain in the vessel.

3. Cleaning

  
3.1 Gauzes — Inner and Outer Gauzes which must be of 28's mesh must be examined and cleaned inside and out, after every working shift. If a gauze is damaged, or if some wires appear thinner than others, it should be replaced. Cleaning must be carried out on machine supplied by manufacturer with appropriate buffs and brushes. Worn gauze brushes can damage the gauzes.
  
3.2 Glass — This should be examined and cleaned after every working shift. If a glass is chipped on the top or bottom seating face it must be discarded.
  
Note Lamp fuel must not be used for cleaning glasses.
  
3.3 Washers — Both top and bottom washers must be in good clean condition. A composition washer is used on top of the glass and an asbestos one below. Make sure they are correctly positioned when assembling lamps. Asbestos washers may require frequent renewal to ensure good seating of glasses.
  
3.4 Relighter Mechanism — Verify that the flint wheel is clean and in good condition and that there is sufficient spring tension on the pyrophor bar (flint) to give a good compact spark. Only approved flints must be used. Any spent pyrophor particles in the bottom of the lamp should be removed just before the glass is replaced. Replaced pinion wheels should not be tight against glass plate as this restricts smooth operation of the relighter key.
  
3.5 Garforth Chamber — Any crust or dirt round the top of the burner tube or in the top of the "Garforth" chamber should be cleaned off daily using a dry rag with the lamp frame in an inverted position. If the crust is not easily removed, a rag slightly moistened with Relighter Spirit may be used — again with the lamp frame inverted, so that neither dirt nor fuel will enter the Garforth chamber. On no account should the crust be removed by abrasive devices such as wire brushes, emery cloth, etc. Check by measurement that the top of the burner tube is at least 0.030 inch above the top of the knurled thimble at all points around the circumference. Assemblies failing to satisfy this requirement must be returned to the manufacturers for replacement of the burner tube.
  
Note New burner tubes made of stainless steel will shortly be available and which will be more resistant to erosion. The new tubes will project above the top of the knurled thimble by at least 0.080 inch and maintenance of this great height should ensure freedom from condensation.
  
3.6 Fuel Vessel — Clean dirt from the top, pay particular attention to the wick, wick tube and wick tube screw. Make sure that the wick adjusting button on the base of the lamp turns easily and that the wick can be turned up freely and turned down to a testing flame position. Verify that the lock enclosure is securely attached to the vessel.
  
3.7 Sintered Ring — Unless the lamp is used in a particularly dusty environment contamination of the sintered ring by dirt will not usually be of significant degree in periods of less than two to three months. If apparent blockage occurs at very frequent intervals i.e. days rather than weeks the cause is more likely to be moisture than dirt and simple drying will then restore the ring to an operative condition. If however dirt is the cause of the blockage the only really effective method of removal of the dirt is by ultrasonic cleaning in a suitable fluid, e.g. at 50/50 solution of benzene and acetone. Scientific Department should be consulted regarding the use of ultrasonic techniques.

4. Trimming

When trimming the wick, the permanent wick, fixed below the trimming wick, should not be interfered with except to be loosened lightly with a pointed instrument occasionally to improve the feed to the trimming wick. This 'stubwick' should be cleaned, the top loosened lightly and trimmed straight, taking care to leave no loose threads. Wick trimming should be carried out frequently, daily if necessary and the wick changed at regular intervals which in the normal course of usage should be about six weeks.

To replace a wick, remove the old trimming wick, take a length of new dry wick and double one end over slightly. Press the doubled end down the wick tube with a pointed instrument (a pricker or very small screwdriver) until it makes contact with the permanent wick, then cut it with scissors leaving about 1/16" projecting evenly above the top of the tube. Note that the trimming wick is only about 1" long.

5. Assembling

After examination and cleaning of all internal parts, which must always be kept clean and dry, see that the washers are correctly positioned on the top and bottom of the glass, and both gauzes fitted. The bonnet (shield) is then screwed on reasonably tightly so that the glass cannot be turned with the fingers. When replacing a glass plate always ensure that the rubber sealing ring round the base of the tube is intact and screw the glass plate down fully before fitting the milled thimble over the sintered ring. Make sure that the slide wire is pushed up, and screw on the fuel vessel. Lock the lamp by placing the plug of the lock on the magnet; this withdraws the bolt and allows the locking cover to be pushed over the bottom ring. Remove from the magnet and ensure that the lock cover cannot be prised away from the bottom ring. Burn the lamp for one hour prior to issue.

6. Daily Testing

The Garforth system is tested by injecting a sample of fresh air by means of a bulb fitted with a brass nozzle and restrictor (a Garforth bulb) after adjusting the wick to give a small testing flame, and observing the effect on the flame. The air sampled in the bulb for this test should be taken well away from any relighter spirit fumes, and the bulb should be squeezed firmly and steadily so as to empty the bulb in about 5 seconds. With a system in good condition, the testing flame will flatten and the yellow eye decrease in size or disappear completely. If there is any distortion, such as pulling up of the edge of the flame, check that the wick tube and the edges of the Garforth chamber are clean; if these are satisfactory a new (clean) sintered bronze ring should be fitted.

Examine the Garforth bulb and check that its component parts i.e. nozzle, restrictor and bulb itself are in good order.

If the nozzle of the bulb does not fit properly in the inlet tube due to a faulty synthetic rubber washer, or if the flow is restricted because of a blocked sintered bronze disc filter, these parts should be removed for cleaning or replacement by taking off the nut on the inlet housing after the glass plate has been removed from the lamp.

7. General

 (i) 
Lamp Bonnet. Frequent hammering out of dents weakens the metal. Replace if in doubt.
 (ii) 
Do not allow lamps to be issued with bent standards.
 (iii) 
All magnetic locks to be tested before issue.
 (iv) 
Excessive movement at middle of vessel is sign of wear, constant watch should be kept for this. Replace if in doubt.
 (v) 
Thinning down of vessel walls mostly due to over buffing should be avoided.
 (vi) 
Leaking vessels should be removed at once, if no facilities in Lamp-room for resoldering, return them to manufacturer.
 (vii) 
Any vessel in apparent good condition not burning the required period should be returned to works for responding. 'Topping up' of burned out vessels must not be allowed.
 (viii) 
Regulator tube must be perfectly free in movement.
 (ix) 
Quantity of lamps available should be watched, as inadequate supplies can result in double shifting and ultimately (skipping' of examination.
 (x) 
Manufacturers 'Name, Type and Approval No.' Plates must be replaced if damaged or obliterated.
 (xi) 
Ensure that fuel is perfectly clean. Use only clean cans which have not been used for any other purpose.

Prev Page Return to Top of Page Next Page



Back

Home
Copyright © 1999-2012 by The Durham Mining Museum and its contributors
Page last updated: 01 Jan 2008

Search

Print