for making forge Iron, but that, on the contrary, it is rather detrimental for the reason, that the blast, when it leaves the hearth, spreads out laterally into a large mass of materials, and proportionally has its force reduced; when if it were applied to half the breadth, or one-fourth of the transverse area, its energy would be maintained, and the process of reduction augmented. In my mind such a result would be assured by a suitably contracted furnace; indeed, whether the same arrangement of contraction, with a modified blast, and a properly regulated burden of ore, would not produce carbonised Iron of every required grade for the foundry, I am not prepared to give a decided opinion, but I certainly incline to the affirmative, for unquestionably the old dogma as to the length of time necessary for concentration is, to a considerable extent, disposed of by modern practice. The passage of the materials down the furnace, as at present constituted, as well as heretofore, is very variable in degrees of speed, and subject to great derangement as to relative positions, those about the centre travelling, of course, much quicker than those at and towards the side, in regard to which the boshes present a formidable obstacle, whose only service is to direct them to the hearth, or bring them back to the stream, from which it had been better if they had never been taken. Some have thought the boshes serve a good purpose, by lightening the pressure on the hearth. That they do so is with mc doubtful, but if they do, still I am unable to see the advantage, for I believe that something like a central column of the materials of (suppose) about the diameter of the hearth, have a free gravitating, tendency to it, and how any harm can arise from that cause I cannot understand; the side materials will, of course, be pressed tardily into the main current, but without any detrimental influence, I think. The impression that I have of the working of the furnace is, that the central portion, from top to bottom, is the main field of operations, and that the side materials are brought comparatively but little into action."
The working expenses of the small tuyere system is greatly in excess of the large tuyere. In Scotland it is a rare circumstance for a furnace to be blown with so few as 3 tuyeres. At the Langloan works they are blown with 4 tuyeres, 2 on each side; at the Dandyvan furnaces 5 are used; at the Gartsherrie 4, 5, and 6; at the Monkland 5; and at the Goran furnaces 8 tuyeres, 3 on each side and 2 in the back. All of these furnaces have large hearths. May not a portion of the excess of fuel to the quantity of blast at these works be accounted for in the use of several small tuyeres? We are not, aware, however, of a single instance wherein the adoption of delivering the blast through numerous small tuyeres has been followed by a superior economy of fuel, blast, or other material, or any other advantage commensurate with its greater first cost and maintenance.
"After much consideration given to the several points embraced in the foregoing observations, I am led to the opinion that a change in the construction of the blast furnace may be advantageously made. If what I have advanced to show the inutility of bellying out the body part, for the purpose (mainly) of obtaining capacity, be correct, why not omit it, and shape the interior of the furnace into a cylinder, from the hearth up to the throat. To meet my views, I would recommend a furnace of the following internal dimensions :— The hearth, 5 feet diameter and 5 feet high; the boshes, 2 feet high, and enlarged from 5 to 8 feet diameter; the body, a cylinder 8 feet diameter and 30 feet high; a shoulder 1½ feet high, and drawn in from 8 to 6 feet diameter; throat, 8 feet high and 6 feet diameter. The content will be some 3,000 cubic feet, and contain about 85 charges. The flues for the gases to pass off by, to be placed in the shoulder below the throat. The height is 46½ feet, but that within which active operations only will be in progress is 38½ feet. The transverse area on which the blast would have to act (in the case) would be only a fourth, or thereabouts, of what is now common, and therefore must, I cannot but imagine, act with much greater vigour and consequent effect, rendering a less amount of it necessary. In what I am now saying I have in view, exclusively, the making of forge pigs, for which I hold that all that is required is simply the reduction of the ores, and the extraction of the Iron. To effect this object, it occurs to me that the figure of the furnace just referred to would be much better adapted to the purposes than the structures in use. I say better adapted, for the following reasons :— 1. That a less quantity of air would have to be blown into the furnace to give the same product of Iron; that a somewhat lighter-powered engine would suffice, and that some relief would be given to the heating stoves. — 2. That as the content of the furnace would be no more than about 3,000 cubic feet, in place of about 5,000, the charges would come down in proportionately less time, which, when alterations of the burden are needed, must be allowed to be of importance. — 3. A further advantage, and one which I consider to be of no little consequence to the well-being of the operations of the furnace, would be the steady, and almost perfectly equable, subsidence of the successive layers of charges, in unbroken relative positions."
The Blowing Machine.
The Blowing Machine in common use consists of a large cylinder of cast iron, furnished with a piston fitting air-tight, the piston rod passing through a stuffing box at the top, and usually connected by a parallel adjustment to the oscillating beam of a steam engine. The cylinder is closed at the two extremities, but there are two lateral openings communicating with the outer air, and two other openings communicating with a side chamber, also of cast iron. It is not unusual for each blowing machine to be provided with two cylinders, which act alternately at each stroke made by the beam of the steam engine by which it is worked. Some of the large Welsh furnaces consume on an average nine tons weight of air in an hour. The pressure at which the air is sent into the hearth varies with the nature of the fuel and the season of the year. An objection to this form of blowing engine is its great size; and Mr. A. Slate, of Dudley, has introduced some improvements He erected, in 1850, at the Woodside Iron-works, near Dudley, a 40-inch blowing cylinder, worked by a steam engine with a cylinder 14 inches diameter. The stroke was two feet, the boiler 27 feet long and 4 feet diameter. On the outlet pipe were placed four tuyeres, two of them 2¼ inches, the others 2 inches diameter. The engine being run up to its full velocity, reached 145 strokes per minute, at which rate the density of the air issuing from the four tuyeres was nearly 5 lbs. per inch; but the engine was perfectly noiseless and steady on account of the great regularity of the blast. With an adjusting expansive valve fitted to this apparatus, its full compliment of blast was thrown into one furnace, viz.: 3,500 cubic feet of air per minute; the pressure of the air in the main close upon the engine was a little over 3 lbs. to the inch; at the tuyeres on the furnace it was rather under; the loss being due to friction and leakage on account of the tortuous character and length of the main, which exceeded 300 feet.
Please Note: These web pages retain the original pagination from the publication