Chapter III.
METHODS OF WORKING OR EXCAVATING COAL; WORKING WITH POST AND STALL, THE LONG WAY, THE NEWCASTLE METHOD — MR. G. ELLIOT'S, OPINION; SIZE OF PILLARS; EXTENT OF GALLERY EXCAVATION. COAL-CUTTING MACHINES — MESSRS. JOHNSON AND DIXON'S, NEWCASTLE; AND MR. PEACE'S, OF WIGAN. ON CONVEYANCE OF COAL UNDER GROUND, BY MR. N. WOOD. ROPES — HEMP, AND IRON AND STEEL WIRE; COMPARATIVE STRENGTH. SCREENING — WALLSEND, SECONDS, NUTS, AND DEAD SMALL.
Methods of Working or Excavating the Coal.
When the engine pit is sunk, and the lodgement found, a mine, which may be six or eight feet wide, is then run into the Coal to the rise of the field. A bed or seam of Coal is not a solid mass of uniform texture, nor is it always of uniform quality for burning. It is often divided and intersected with its accompanying strata, by what are locally named partings, bands, &c. Besides the chief partings at the roof and pavement of the Coal seam, there are subordinate lines of parting in the mass of Coal of variable dimensions inseparable to the former. In British practice, there are four different systems of working Coal mines.
1. Working with pillars and rooms, styled post and stall, where the pillars left bear such proportion to the Coal excavated as is just adequate to the support of the incumbent strata.
2. Working with post and stall, where the pillars are left of an extra size, with the intention of subsequently removing a considerable proportion of each massive pillar, when the regular working of post and stall has been finished in the colliery.
3. Working with post and stall, or with comparatively narrow rooms or boards, whereby a much larger proportion of the Coal is left with a view of working back towards the pits or shafts, and then taking away every pillar completely if possible.
4. Working by the long way, or the Shropshire method, which leaves no pillars, but takes out all the Coal progressively as the workings advance.
The post and stall system is practised with Coal of every thickness. The Shropshire method, working by the long way, is adopted with thin Coal, which is worked from 2½ to 7 feet. The principle of long wall working is the extraction of all the available Coal by the single process of first working, maintaining the roads by means of stone walls or wooden props. This system is applicable only, with advantage, to thin seams lying near the surface, and in which the workings may be of a very limited extent. The long wall system is liable to many practicable objections, such as the difficulty of maintaining the roads to any great distance, of forcing ventilation through troubles, the limited command of wall face, and the ruinous effect of pressure upon water courses. One of the most extensive workings on this system is in the neighbourhood of Edinburgh, at the Edmonstone and Sheriff Hall Collieries, in seams of four and five feet thick, with both good and bad roofs. The thin Coal and ironstone mines in Staffordshire are worked in a similar manner. Throughout Yorkshire, the mines are worked upon what is termed the Yorkshire long wall method.
The method, now known as the Newcastle system, is considered the most perfect for the working of a mine. It is named panel work, because the whole area is divided into quadrangular panels, each panel containing an area of from eight to twelve acres; and round each panel is at first left a solid wall of Coal, of from 40 to 50 yards thick. Through the panel walls, roads and air-courses are driven in order to work the Coal contained within these walls. Thus, all the panels are connected together with the shaft as to roads and ventilation, and each district or panel has a particular name, like a city square, or block of houses, so that any circumstance relating to the details of the colliery can be readily referred to a specified place. This is termed the pillar and stall, or board and pillar system; by this mode of working, it enables separate sets of workmen to be employed in different quarters, and large quantities of Coal at ready command; and where faults are met with they are made auxiliaries to the formation of these barriers. By this arrangement general creeps are prevented; and, as the pillars are worked in limited quantities at each position, the Coal is less damaged by pressure, and the process of ventilation much more conveniently managed than where a large extent of workings, without separation, is to be dealt with. Equivalent to this principle is the formation of pillars, so exorbitantly large, that the working of them away may be carried on in the vicinity of the working boards, without any danger or creep. These, then, are the chief advantages of the board and pillar system, the adoption of which has given the collieries of the North of England their extraordinary powers of production; because, in an extensive field, the principal horse roads radiate from the shaft into various districts, each of which holds an independent set of workmen, whether in the first, second, or mixed stage. In the counties of Durham and Northumberland, a mode of excavating the Coal from the extreme boundary of the mine to the shaft, instead of advancing from the shaft to the boundary, is becoming somewhat general, where a colliery has more than one pit. After two, three, or four drifts have been made from the downcast shaft, and the requisite drifts formed throughout the ground intended to be worked, the remainder of the Coal, but much the larger portion, is in pillars or blocks. In working these, instead of proceeding forward from the shaft, which is the usual way, the miner commences at the extreme boundary of the mine, working backwards to the shaft, and clears all the Coal away at once. This is found to be a much more profitable plan of working, though in the first instance it requires more time and outlay of capital.
"Modern practice has decided, says Mr. Elliot, Mining Engineer to the Marchioness of Londonderry, that to leave large areas of pillars is neither so economical in the working of a colliery nor so safe against accident; the approved practice now being either to work the Coal by means of a long wall or by large pillars, removing them simultaneously with the working in the whole Coal. Again, we have the system of working the lower seam entirely out first before entering the upper seam. This is frequently done without either much inconvenience or injury to the seam above, although frequent
Please Note: These web pages retain the original pagination from the publication