iron circles to be constructed of segments. Mr. Matthias Dunn first introduced tubbing into Scotland, in the sinking of a shaft at Preston Grange, in 1830. Iron tubbing consists of short cylindrical portions, the cylinder, as at Hebburn, being formed of ten segments, each of which segment weighing about 4½ cwt. of solid iron, with the exception of a hole for the purpose of raising it. The only drawback to this mode of tubbing, is its liability to be corroded by saline waters, especially in hot smoking shafts, where the metal is found, in the course of time, to carbonize to such a degree, that it may be cut with an ordinary pocket-knife. In such cases, the tubbing will sometimes give way, and let down the waters behind, and bring ruin and disaster with it. This, however, can happen but rarely, and by careful inspection may be foreseen. An unusual quantity of metal tubbing was required at Harton Winning, a colliery situated near South Shields, where Professor Airey, Astronomer Royal, conducted his interesting pendulum experiments in 1854. (See "History of the County of Durham," vol. ii., p. 732 — 1857. In this shaft, no sooner was the water stopped than, upon sinking underneath, it followed down the chinks of the strata, requiring a succession of tubs till eighty fathoms were completed, which was surmounted by eleven fathoms of walling. Assuming that those waters were derived from the surface, then the lower tubbing sustained fifteen atmospheres, or a pressure of 225 lbs. per square inch! But the most celebrated winning in the Northern Coal-field was that of Pemberton's Pit, Monkwearmouth; and in describing Pemberton Main Colliery, particulars of this expensive winning will be given.
Steam Power.
A plan of general drainage by steam power, as applied to a portion of the Northern Coal-field, has already been referred to; but this does not obviate, in the winning of a deep colliery, the necessity of calling in the aid of the steam engine and pumping apparatus; indeed, they are indispensable. The concentration of steam power applied to pumping water out of shafts and pits, is at some places enormous. Of course the amount of power requisite varies with the condition of the strata, the shafts, and the Coal. The amount of power employed at the new winning of the South Hetton Company, Durham, is said to be the largest; the diameter of the cylinder of the pumping engine is 84 inches. They are condensing and double engines, and are amongst the largest and most powerful ever erected. The engine power employed at Haswell, Friar's Goose, Percy Main, Hebburn, Jarrow, and other collieries, will be noticed in another portion of this work — "Collieries." The winding, or drawing steam engines, are employed for raising the Coals, and also serve for lowering or lifting the men and boys, and for drawing purposes in general; these are, of course, separate from the pumping engines. The Great Hetton Coal Company have the largest amount of drawing steam power; there are eight shafts and eight winding engines, four of which are each of 100 horse power. The technical engineering mode of reckoning the duty of their engines, is to calculate the number of pounds lifted one foot high by the expenditure of one ton of Coal in the fire-box of the engine. At Hetton this number frequently exceeds 40,000,000lbs. Small steam engines are occasionally erected underground for the working of inclined planes, and aboveground for saw mills and other purposes connected with the aboveground works.
In each pit there are one or more pumps, varying in size in proportion to the work to be done. Sometimes they are 12, 18, or even 24 inches diameter. If there be two or three pumps or cylinders, they are placed side by side, and supported at intervals by beams fixed across the pit; cisterns being placed at different elevations, to which the water is raised, and if possible delivered off by an outlet considerably below the surface. In some instances also, cisterns are placed at the level of feeders of water that occur at a distance of many fathoms from the bottom, and deliver some hundreds of gallons per minute, so as to save the waste of steam power, which would be caused by allowing this water to fall to the pump, and raising it through the whole length of the pump.
Those numerous pumps, steam engines, smoke, and noise, at a 11 large colliery establishments, are thus noticed by Mr. Howitt, in his "Visits to Remarkable Places" :— "Wherever reared themselves those tall engine houses, there also towered aloft two vapoury columns, one of black smoke, and one near it of white steam. These neighbouring columns, like the ghosts of Ossian, slanted themselves in the wind, and wavered spectre-like in the air, each like some black demon with a pale spirit in his keeping, whom he was compelling to enormous labours; and such noises filled them as served to confirm the belief of it. Some of these engines were groaning, some puffing, some making the most unearthly sighings and yawnings, as if the very Gouls and Afrits of the Eastern stories were set to stupendous labours, and were doing them in despair."
The Coal Won.
The shaft having been completed down to the Coal, it must now be continued an indefinite distance further as a "sump," to provide "standage" for the water. And, as this is a necessary portion of mining economy, it is often advantageous to carry out driftings in stone or Coal, so as to secure a reservoir for at least a few days' or weeks' accumulation; an unexpected influx of water is thus provided against, or the interruption of the pumping power by unforeseen accidents. There must be either two shafts, one of which is called the downcast and the other the upcast, or one shaft must be made into an upcast and a downcast. This latter result was commonly obtained by dividing the single shaft with a wooden partition, ext ending through its whole length, and termed a brattice. If there be only one shaft, and that be bratticed, then all things must be so laid out as to tend back to that one spot. If there be two shafts at similar distances, the plans tend to the bringing of Coals to one shaft, which is called the drawing shaft, and the ventilation of the mine by the other shaft. In almost every colliery there is a considerable amount of water; for so soon as you begin to work the Coal, or rather before doing so, you must arrange for the permanent drainage of the mine, and this is the constant work of the pumping engines. The strata of every Coal-field has a certain inclination called the dip and rise, as well as commonly a level line of bearing, forming right angles therewith. Now, as the drainage will generally follow the descent of the Coal-measure, it will be necessary to select such a situation for the engine pit, that when the excavations for getting the Coal are extended, the water, instead of accumulating in the works, may run off to the place where the pumps are brought to meet it. With this view it is usual to sink the engine pit at the lower part of the field, the drawing shaft (if there are two shafts) being at a short distance above, on the rise of the strata.
Please Note: These web pages retain the original pagination from the publication