breakers or fractures come up from one seam to the other, when the chief difficulty is to deal with the gas that ascends from the lower seam; this, however, to my knowledge, has never been found insurmountable, nor do I think that generally the working expenses of the upper seam are much increased, nor the percentage of small, neither is the size or quality of the large Coal materially injured by this mode of working."
From extensive practical observation, continues Mr. Elliot, "I have found, that by first working the upper seams the lower seams are improved in hardness, in yield of merchantable Coal, the roof improved, and all the incidental work, except the hewing economised by this system. It will then become a question for practice and further experience to determine if it will not be the better way of working collieries, especially those of great depth, by excavating the upper seam first, although as a rule the Coal is not so strong, and yields more small Coal than the same seam of Coal would do at a less depth; and although it might not in itself be so remunerative to the owner to work, still I conceive that the advantage gained by the improved value of the lower seams would fully compensate for the diminished profit on the upper seam. I am of opinion, therefore, that it will prove to be of permanent advantage to deep Coal mines, to work the upper seams first, and so improve the lower beds in hardness."
With respect to the proportionate size of the pillar to the board, much depends upon circumstances; but depth from the surface forms the chief consideration. A colliery 60 fathoms deep will require, for the adequate support of the workings until the time arrives for their removal, pillars of the size of 20 yards by 5; of 100 fathoms, 22 by 9; 120 fathoms, 22 by 10; 140 fathoms, 24 by 11; 160 fathoms, 24 by 12; 180 fathoms, 26 by 14; 200 fathoms, 26 by 16; 300 fathoms, 30 by 24. The Monkwearmouth Colliery, at the depth of nearly 300 fathoms, has been worked with five yards openings, whilst the block of Coal left is 40 yards by 29. The collieries at Seaton, Seaham, and Ryhope are of similar depth with corresponding openings.
When mines are fully worked the main shaft is frequently continued down to other seams of Coal, which are excavated in the same way as the first seam. In such cases the workings communicate with each other by smaller shafts, called "staples," which are sunk at intervals between the seams of Coal.
The extent of gallery of some of the older Coal pits is very great. St. Hilda Colliery, near South Shields, has underground workings of the mine equalling eighty miles in gallery extent; the Killingworth Pits have 160 miles of gallery excavation! and of similar extent are those of the Western District, such as Townley, in the parish of Ryton: whilst at the Howgill Pits, Whitehaven, the mining has been carried more than 1,000 yards under the sea, and about 600 feet below its bottom.
In Scotland, until within late years, the general system adopted was, to have all the excavations from four to five yards wide; and the pillars, constituting one-fourth or one-third of the mine, being given up for lost. The long wall system may now be said to prevail generally throughout Scotland, except where the seams of Coal are too thin. At the collieries at Slamannan, Sterlingshire, the Coal and loose strata at the top occupy only about 2 feet 8 inches, above which is a compact sandstone; the floor of the mine being pretty firm fire-clay. The levels, with a pillar of six yards between, are advanced to win out the Coal for work; and at every twenty yards a tramway is commenced 5½ feet in height, which, upon each side is defended by a stone pillar three or four yards in thickness, formed of the sandstone roof. The intermediate space is either hollow or partially filled with the refuse of the working. The Coals are conveyed along the wall- face to each tramway upon platforms, having low broad wheels, where they are filled into tubs, containing 4 cwt. each. Very little timber is used in this work; and from the compactness of the Coal, the pressure breaks it off from the solid, in large flakes, at the same time that the work is kept safe and open. In this manner are the collieries worked in the West of Scotland, where thin seams prevail.
Coal-Cutting Machines.
We appear to be on the eve, however, of a great revolution in the mode of working or excavating Coal. Manual labour in the hewing of Coal is likely to be superseded by the introduction of machinery. A Coal-cutting Machine has been invented by two parties in different districts, and the trials have so far given satisfaction. If the invention is followed up with spirit so as to procure its general adoption, an immense saving will no doubt be effected in the working of our collieries. The machines are worked by compressed air, and there will be this additional advantage, that an improvement in the ventilation of the mine must follow, from the continuous flow of exhaust air throughout the workings.
The Coal-cutting Machine of Messrs. Johnson and Dixon, Newcastle, is constructed to work along the face of a "long wall" of Coal, a horizontal revolving cutter, 3 feet 6 inches long and 3 inches diameter, being first made to penetrate the bottom of the wall, or block of Coal, after which the machine propels itself forward, leaving a continuous channel, extending 3½ feet into the solid Coal and about 3 inches in height. The revolving cutter is shaped nearly like a screw tap, which, if moved laterally along in a direction at right angles to its own axis, would cut a similar trench in a block of Coal. The four tiers of cutters or teeth are of chilled cast iron, and when worn can be easily replaced at a nominal cost. The projecting spindle to which they are attached is driven at 500 revolutions per minute by a double cylinder compressed air engine, which is mounted upon the moveable frame of the machine. The air is compressed to a pressure of 401b. or 501b. per square inch, by a 10-horse power steam engine, situated above ground, or in any other convenient place, and is conveyed to the machine through 4-inch metal pipes, terminating in about 30 feet of stout flexible india-rubber hose-pipe of the same diameter, which allows the machine to travel either day or night, a certain distance forward without stoppage. The rate of working is 6 inches a minute forward, equal to 120 square yards in 12 hours. Two machines, therefore, which, with engines and air pumps complete, would cost about £1,750, would cut 80,360 square yards, equal in a 4½ feet seam to 120,540 tons of Coal in a year of 287 working days, and working each machine only 14 hours daily. The whole cost of upholding and working the two machines is estimated at £1,580 per annum, which is equal to little more than 3d. per ton of Coal worked, the present price being from 1s. to 1s. 9d. Although, up to the present time, applied under the disadvantages of the "pillar and stall" mode of working, instead of the "long wall," for which the machine is intended, yet so far as the cutting of Coal has been tried, the machine answered its purpose thoroughly. This invention was patented in 1856.
Please Note: These web pages retain the original pagination from the publication