|
18th July 1936, Page: 6, Column: 1 Falls And Accidents In Bord And PillarReport by Messrs. Hudspeth, Phillips and Walker. Concluded from page 405, No. 26, Vol. 46. Effects of Certain Factors. (a) Method of Getting. — The method of getting in given circumstances has a definite bearing on the roof conditions. When fracturing of the roof occurs where the cleat is first broken, breaking the cleat at alternate sides of a bord results in diagonal and associated secondary fractures. Similar conditions result from indiscriminate breaking of the cleat such as often occurs when getting by hand or by pneumatic picks. in the absence of control, fracturing is extensive and irregular with consequent bad roof conditions and a greater liability to falls. With percussive coal-cutters fracture control and good roof conditions obtain (except where the coal is tender) if the undercut is first squared out at the side where the most advanced cleat is first cut by the face. Where arcwall coal-cutters are used in these circumstances, however, the point at which the cleat is first broken clearly depends on the direction of the roadway relative to the cleat; if at right angles, it will be at the centre of the place where fracturing is undesirable. It is an advantage for the roadway to make some angle with the cleat so that the first breaking of the cleat, and fracturing, occur nearer to one of the sides. Measurements at the face have shown height reduction to be at a maximum rate when cutting and shot-firing, after which roof fracturing has often been observed. In these circumstances there is a great liability for fails to take place while the coal is being filled, even before temporary supports can be set. However, where a roof contains cauldron bottoms the use of coal-cutters tends to reduce the associated danger, for they often fall with the coal when it is shot down, whereas when working by band a support may be applied at the edge of a cauldron bottom — a condition conducive to danger, as on being further exposed the cauldron bottom may displace the support. Machine under-cutting is generally done under comparatively strong roofs. Where the roofs are weak the coal is generally worked by hand or pneumatic picks because of the need for support close up to the face. (b) Nature and Sequence of Strata. — More extensive fracturing occurs in shale roofs, and thick sandstone roofs generally remain unbroken except where inherent weaknesses exist, but much depends upon the strata sequence. A bed of sandstone unbroken if overlain by a more rigid rock may break down if overlain by a more yielding shale. The effect of this factor is again intimately associated with that of depth, a roof strong enough to withstand the forces acting upon it in a shallow working may fail at a greater depth. (c) Width of Working. — Except in shallow workings and when considered in relation to nickings (which are in effect extremely narrow workings) this factor is relatively unimportant. In shallow workings increase in the width of a place is often associated with worse roof conditions, hence the reduction in width when holing or turning away places. At depth, the working width, within practical limits, does not affect the roof conditions, though a reduction in width to 6 ft. or thereabouts has been found experimentally to result in more extensive fracturing at the face. After a time, however, the wider place becomes the worse, Nevertheless, irregular variation in width is liable to result in fracturing or in change of direction of any roof fracture developed at the side of a working. Turning-away and Holing Bords and Walls. — When developing bord-and-pillar workings, bords and walls are usually turned away as they are won out. In these circumstances roof breaks are seldom encountered beyond the sides of the first working. Should coal have been left overhanging, however, any fracture developed at the side of the first working is exposed as the over-hanging coal is removed, and because bords are the more frequently fractured, the turning-away of a wall is usually carried out under more broken roof conditions. When turning a place away at a point some distance back from the face, however, the new working will pass through the abutment-pressure area where the roof may have been fractured parallel to the sides of the first working. These fractures are the "holing breakers" found when splitting old pillars. Because of the weaker roofs generally found in the shallower workings, it is common practice to reduce the width of a working place (particularly a bord) when turning-away or holing with a view to ensuring good roof conditions at the junction. This is not effective in deep workings because of the greater effect of increased shear there associated with width reduction. (e) Other Factors. — Depth is a factor of considerable importance. No appreciable differences in roof conditions have been observed due to variation in rate of advance, or seam thickness from 3½ to 6 feet. Where the roof stratum consists of shale it often contains cleavage-planes corresponding approximately in direction to the coal cleat but at wider intervals. These cleavage-planes do not generally influence the direction of the primary roof fractures (practically at right angles to the cleavage in bords), but they increase the extent of secondary fracturing, and falls are more liable to occur. Some Conclusions. The forces acting on undisturbed roof-strata are compressive, and the lateral pressure is less than the vertical pressure. As bords and walls are driven the load is redistributed, the vertical and lateral compressive forces acting upon the adjacent strata are increased, and bending and shearing forces are induced in the roof. The nature of a roof fracture is characteristic of the kind of force which is the predominating cause of failure, and three main types have been recognised which are more or less associated with depth at small depths bending forces predominate, at greater depths shearing and/or lateral compressive forces are the more important. In some cases, where the roof consists of thick shale overlain by sandstone, fracturing of the roofs of bords can be prevented by the driving of pressure-relief bords. The more immediate causes of falls, however, are the fractures induced subsequently. These have no regular arrangement, and initiate at points of high local stress, connecting up with each other or with primary fractures or inherent weaknesses so forming isolated and detached pieces of rock which may readily fall. It is desirable that equal resistances be developed in the several supports, and that they be not too great. Closely-spaced supports not only prevent small falls from occurring but also result in better load distribution. The presence of inherent weaknesses in the strata and the irregular development of secondary fracturing call for constant vigilance under all circumstances. Where the fractures in shale roofs of bords indicate lateral compression, fracturing of the roof can be controlled by nicking or other systematic first breaking of the cleat at one side of the faces of the bords where arcwall machines are used, this is effected if the roadway makes a sufficient angle with the cleat. Fracture, if any, will then occur at this side and improved conditions will result providing supports are not set directly beneath the fracture. Where arcwall machines are used and the roof fractures are due to the predominance of shearing forces, the more pronounced fracture is at the side where cutting is commenced, and roof conditions are better if this is always done at the same side of a place. The maximum rate of roof movement occurs close to the face, and the sooner the supports are set the more effective will they be the undercut coal should be early and securely spragged. When the coal is machine undercut and shot down an area of unsupported roof is exposed for a time as supports cannot be set until some coal has been filled away, and where the roof readily fractures at the face it is often advisable to work by methods which allow the supports to be set sooner.
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||