|
26th July 1930, Page: 8, Column: 2 Examination QuestionsSecond Class (Under-managers)*1. — MINE WORKING. 1. Describe a shaker conveyor for use along a coal face. What are the limitations of this type of conveyor? Also describe various suitable positions for the driving engine. (60) 2. How would you line a sinking shaft with brickwork from one bricking ring to the next? Illustrate your answer with sketches. (60) 3. The timber in a roadway is broken and requires renewing. There is a considerable weight of finely broken debris on the covering wood. Explain how you would take out the broken timber and substitute steel arches. What precautions would you take until the steel arches were fixed? The road must be ready for traffic each morning. (60) 4. Describe, with sketches, two methods of obviating a dust-laden atmosphere whilst drilling shot-holes in hard sandstone. (60) 5. During severe frost ice tends to form in certain downcast shafts to such an extent as to be a source of danger. What arrangements would you make to prevent this? (60) 6. What is your opinion of steel props as compared with wood? Describe two or three types of steel props, and state the advantages and disadvantages of each. (60) 2. — THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine, which accompanies this paper, show how you would ventilate the working places. Mark the direction of each air-current; also indicate clearly the positions of air-crossings, doors, stoppings, regulators and sheets, using the signs laid down in the Regulations. Sheets to be shown thus S. Coal is to be wound at the downcast shaft only. (75). 2. Sketch any type of flame safety-lamp known to you. Describe the method of using it to test for the presence of firedamp; and state what height of cap you would get with several different percentages of firedamp. Do you prefer a round or a flat wick, and why? (45). 3. State fully how you would ventilate a single heading; expected to reach an ultimate length of 200 yards, in a fiery mine. Give particulars of all the appliances required, and describe how you would fix and use them. (45) 4. A motor develops 100 horse-power effective, in order to drive a fan producing 120,000 cubic feet per minute in the fan drift of a certain mine. What horse-power would be necessary in order to produce a quantity of 180,000 cubic feet per minute under similar conditions? Calculate the water-gauge reading at the fan drift in each case. (45) 5. What is the principle of the water-gauge as used in connection with ventilation? Describe its use and give an illustration of two or three different readings, in the same ventilating district, stating what information is conveyed by each of these. (45) 6. What methods are adopted for measuring the quantity of air passing any given place? State fully the method you employ; and what precautions you take so as to reduce the chances of error. (45) 7. State briefly what you know about "natural ventilation" and how you would ascertain if this is an advantage or otherwise in any given case. (45) 3. — EXPLOSIONS, ETC. 1. Give a list of the materials required in the ordinary working of a mine which need special care in their use, and storage to prevent danger from fire. What arrangements are necessary to ensure safety with each material you name? (20) 2. What arrangements would you make for dealing effectively with coal dust in a dry mine? A sample of dust taken from the roof, floor, and sides of a mine roadway contains 65 per cent. of incombustible matter. Would you be satisfied that this roadway was in a satisfactory condition? Give reasons for your answer. (20) 3. What dangers may be apprehended when coal-cutting and conveying machinery is extensively employed in a dry and dusty mine yielding firedamp? What special precautions should be taken: (a) When using compressed air; (b) When using electricity ? (20) 4. It becomes urgently necessary to seal off a district in which heating has developed. Preparatory stoppings of brickwork have been built, but are badly crushed. How would you proceed? (20) 5. A panel of old workings containing water lies partly to the rise of new workings in the same seam. The seam dips at an inclination of 20°. Illustrate by a sketch how you would approach these old workings, and drain off the water. (20) 6. As under-manager of a mine you receive a report that an explosion has occurred in a section of a mine at a distance of 1 mile from the pit bottom, and that a number of men are missing. What would you do? (20) 4. — MACHINERY. 1. What is a common construction for a steel wire winding rope, say 1 inch diameter? How would the construction change — (a) To allow of the rope coiling on a small drum; (b) To make the rope non-spinning? (20) 2. What is the brake-horse-power of an engine having one double-acting cylinder 24 inches diameter x 48 inches stroke, making 100 r.p.m. with a mean effective pressure of 30 lb. per sq. in. and a mechanical efficiency of 75 per cent. ? (20) 3. Describe the plans and apparatus that you would expect to find in a pit bottom pump house where water — about 750 g.p.m. — is pumped to a height of 900 ft., using electric power. (20) 4. Describe the winding engine best known to you, mentioning its main dimensions and type of valve gear and the auxiliary or accessory plant found in the engine house. (20) 5. A spindle or shaft for a rope sheave is 18 inches long, 4 inches diameter at the centre, turned down to 3 inches diameter for a length of 4½ inches at each end for bearings. Using a scale of one-half full size make a side elevation of the shaft. Make also an end elevation (by compass or freehand) showing a keyway ¾ in. wide and about ¼ in. deep in the 4in. portion. (20) 6. What are the differences between a 3-phase induction motor with wound rotor and a direct current shunt wound motor? (20) 5. — ARITIIMETIC AND SURVEYING. Arithmetic. — 1. Calculate the quantity of coal in an area of 5 ac. 3 ro. 20 po. of a seam 63 inches thick. Specific gravity of coal, 1.280. (20) 2. The earthwork excavation in the formation of a circular pond is 523.6 cubic yards. The depth of the excavation is 5 ft. What is the diameter of the excavation? (20) 3. A coal washer yields in three classes of washed coal (a) 10½ per cent. ; (5) 54 per cent.; and (c) 35½ per cent. The selling prices of these are 15s. 6d., 12s. 3d. and 5s. 4d. per ton respectively. What is the average price of the yield per ton? (20) 4. A three-throw pump, with rams 12 inches in diameter and a stroke of 18 inches runs 15½ hours in 24 hours at 30 r.p.m. Calculate the feeder of water if the delivery be 92½ per cent, of the capacity. (20) Surveying. — 5. You are instructed to lay off the line of a roadway on the bearing N.65°E. Make a hand sketch of the face of the dial. Mark the cardinal points on the full circle graduation, and the position of the needle when the sights of the dial are in the line to be laid off. (20) 6. Plot a section from the following levelling notes :—
Mark the gradient from A to B and the cutting, or filling, at each station to give a uniform gradient from A to B. Scale for horizontals 1 in. to 50 ft. and for verticals, 1 in. to 10 ft. (20) 7. Plot the following short traverse with a loose needle on a dial reading clockwise, the north sight always leading :—
Plot to a scale of 1 in. to 200 links. The measurements are level. Give the bearing from B to A and the distance. (20) 8. If the lines No. 2 and No. 4 in question 7 had been measured on gradients of 1 in 3 and 1 in 4 respectively, what would have been the correct plotting lengths of these lines ? (20). 6. — MINES ACT, ETC. 1. (Compulsory Question). Write a report such as you might be asked to present monthly or weekly to your manager, as to the condition of a mine of which you are under-manager dealing with matters you would consider likely to be of importance. (20) 2. What are the General Regulations regarding the use of electricity for working coal-cutting machines ? (20) 3. Quote, as nearly as you can, the definitions of the following expressions relating to Electricity as given in the General Regulations :— (a) "Medium Pressure." (b) "Apparatus." (c) "Open Sparking." (d) "Electrician." (20) 4. (a) What are the provisions of the Coal Mines Act, 1911, and General Regulations relating to the measurement of ventilation? (b) What standard does the Coal Mines Act, 1911, lay down as to "adequate ventilation"? (20) 5. Give an outline of the General Regulations regarding the provision of first aid and ambulance, as prescribed by the new Order which came into force on April 1st, 1930. (30). 6. What are the precautions as to safety required to be taken, by a coal-getter in his working place, in order to comply with the Coal Mines Act, 1911, and the General Regulations ? (20) * Questions set at Examinations in May, 1930. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not bean reproduced. For First Class see page 408, No. 28 Vol. 40. Complete sets of questions available through H.M. Stationery Office, 1s. 6d. net.
|
|||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||