|
12th July 1930, Page: 408, Column: 1 Examination QuestionsFirst Class (Managers)*1. — WINNING AND WORKING. 1. In a moderately hard seam 4 ft. thick, with a good roof, it is intended to drive a place about 40 yards wide to the full dip of 1 in 4, from which coal faces will later be opened out on each side. Sketch the setting out of this work, showing the roads and packs, and give a description of the machinery you would install in order to advance the place with all possible speed. (50) 2. What are the main sub-divisions of the Carboniferous System? How would you correlate the measures of one district with those of another district in the same coalfield? (40) 3. Sketch, in plan and elevation, an underground stable suitable for 20 horses. Mention all essential details to be provided for, excepting fodder. What provisions should be made so that roads may be specially suited for horses ? (40) 4. A 10-in, rising main has to be put in a shaft 400 yards deep fitted with rope guides. What kind of pipes would you use, and how would you secure them? The water forms a deposit inside the pipes. Explain what arrangements you would make for cleaning them out. How would you allow for expansion and contraction? (40) 5. Compare a scraper loader with a shaker, or with a belt conveyor, for taking the coal along the face. (40) 6. Under what conditions are the following methods of shaft sinking likely to be the most successful (a) Drop shaft; (b) Cementation ; (c) Freezing ? (40) 7. What are the disadvantages of drilling shot-holes vertically for roof ripping, and under what circumstances are vertical holes considered to be an advantage ? (40) 2. — THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine, which accompanies this paper, show how you would ventilate the working places. Mark the direction of each air-current; also indicate clearly the positions of air- crossings, doors, stoppings, regulators and sheets, using the signs laid down in the Regulations. Sheets to be shown thus Coal is to be wound at the downcast shaft only. (50) 2. Sketch any type of flame safety-lamp known to you. Give a description of the method of testing for firedamp with this lamp when burning a mixture of 33 per cent. petroleum and 67 per cent. of colza oil. Give sketches of the cap you would expect to get with several different percentages of firedamp: (a) with a round wick; (b) with a flat wick. State which type of wick you prefer, giving your reasons for the preference. (30) 3. If you have two parallel airways, an intake and a return, each 1,000 yards long, of the same dimensions and type of surface, passing 20,000 c. ft. of air per minute into and out of a large district; the reading of the water-gauge at the separation doors at the outer ends of these roads being 4 in., and at the inner ends 1 in. — state what results you would expect to find if another similar roadway is made and used as the second intake, other conditions both outbye and inbye being assumed to be the same. (30) 4. What horse-power of ventilation is required to produce a current of 200,000 c. ft. air per minute through a mine when the water-gauge at the fan drift is 4 inches? Assuming an efficiency of 65 per cent, in the fan, what H.P. must be given out at the motor to produce this quantity? If it is required to increase this quantity to 300,000 c. ft. per minute under similar conditions, give the H.P. that would be necessary at each of the two points named. (30) 5. What is the geothermic gradient? How would you ascertain this in any given case of a deep mine? State fully how the effect of this may assist or retard the ventilation of a mine. (30) 6. Sketch a Sirocco ventilating fan, equal to producing 200,000 c. ft. per minute with a water-gauge of 6 inches. Show the passages connecting this fan to a mine, and the means by which the air- current can be reversed when necessary. Give the principal dimensions. (30) 7. Sketch two methods of producing ventilation in a single heading, which is expected ultimately to reach a length of 200 yards, the mine being fiery. Give full particulars of the appliances necessary, bow they are used; and state which of the two methods you prefer, and why. (30) 3. — EXPLOSIONS, ETC. 1. How would you lay out the workings in a seam of coal liable to spontaneous combustion? The seam lies at a depth of 700 yards from the surface, it is 6 ft. thick, with a shale roof, and hard floor, dipping 1 in 5. What special precautions should be taken in the actual working operations, and what preparations should be made to deal with a case of spontaneous heating or fire? (30) 2. Enumerate the conditions which may arise in mines to affect injuriously the health of the workmen. What precautionary measures should be taken under the conditions you give? (25) 3. As manager you receive a report that an explosion has occurred in a section of the mine at a distance of one mile from the pit bottom, and that a number of men are missing. Set out in detail the steps you would take for their recovery. (25) 4. A district in a mine which has been sealed off in consequence of a fire is to be re-opened end recovered. Whet considerations should be taken into account before re-opening the district, and what precautions should be taken during the operations? (25) 5. Sketch and describe: (a) An underground ambulance carriage for use in highly inclined seams. (b) A suitable appliance for raising injured persons to the surface in shafts where the cage is not large enough to permit of a stretcher being laid fiat. (25) 6. What dangers may be apprehended when coal-cutting and conveying machinery is extensively employed in a dry and dusty mine yielding firedamp? What special precautions should be taken: (a) When using compressed air; (b) When using electricity? (25) 4. — MACHINERY. Electrical Section. — 1. What is meant by "power factor" in electrical power applications? How can the power factor be raised and what are the advantages of raising it? (28) 2. The neutral point of a 3-phase electrical system may be "earthed" or "insulated." What is meant by these terms ? What are the advantages and disadvantages of an earthed neutral? (28) 3. The brake-horse-power of an electric haulage is 75. The mechanical efficiency of the haulage gear is 0.8 and the efficiency of the motor is 0.88. The electric power is 3-phase 50 cycle 400 volt at a power factor of 0.8. What will be the current in amperes? (28) Mechanical Section. — 4. Describe the mechanical parts of an electric motor-driven pump suitable for placing in an inbye pump-house to raise about 60 g.p.m. of water to a head of 300 ft. (28) 5. A centrifugal pump has a delivery branch 2-inch bore, with flange 6 inches diameter, drilled for four bolts 5/8-inch diameter on a 4½-inch bolt circle. The rising main is to be of pipes 3-inch bore with flanges 7¼ inches diameter drilled for four bolts 5/8-inch diameter on a 5¾ inches bolt circle. Make a freehand drawing of a short straight matching pipe (an assembly of pipe parts will serve if preferred by the candidate) to couple between pump and rising main. Show all dimensions and description needed for constructing the matching pipe. (38) 6. What are the troubles commonly met with in the upkeep of Lancashire boilers ? Describe how they are dealt with. (28) 7. Describe a condensing plant suitable for a steam turbine of say 1,000 k.w. output. (28) 8. Describe a plant or gear suitable for placing at the top of self-acting incline in which a set of full tubs descending hauls up a set of empty tubs. (28) 5. — SURVEYING, LEVELLING AND DRAWING. 1. A seam of coal which has a dip of 1 in 5 in a direction S.55°E. is intersected by a fault running North and South which has a vertical displacement of 35 ft. down to-East and a bade of 35° to the vertical. Draw a plan of the fault and show a contour line across the, fault as it would appear on a working plan. Draw to a scale of 1 in. to 50 ft. and show the contour for a distance 100 ft. on each side of the fault. (25) 2. Plot a section from the levelling notes following and mark the depth of cutting, or filling, at each station to give a uniform gradient from A to B
Scale for horizontals of section = 1/480. Scale for verticals of section = 1/120. (30) 3. Calculate the quantity of coal in an area of 555 acres in a seam 65 in. in thickness and of a specific gravity of 1.280. Make a deduction of 15 per cent, and calculate the total royalty the seam would yield at 6½ pence per ton on the remainder. (25) 4. Two parallel faults running on the dip and rise of the strata, forming a trough area, are encountered by a level in working a coal seam. The first fault with a bade of 20° has a vertical dis- placement of 130 ft. down and the second on a hade of 15° has a vertical displacement of 86 ft. up. The distance between the faults at the bottom of the trough is 230 ft. Draw a section across the trough and find therefrom the length and gradient of a drift across the trough from the seam on the one side to the seam on the other. (30) Note. — The hade of the faults is from the vertical. 5. A pump which delivers 550 gallons of water per minute stands for 36 hours after emptying the standage. It then runs 50 hours continuously till the standage is again empty. What is the feeder of water? (25) 6. A heap of coal 360 ft. by 130 ft. on a rectangular base lies on level ground. The height of the heap is 18 ft. vertical. The slope of the coal is 45 degrees. Calculate the cubic contents of the heap, and the quantity of coal in tons, using the weight per cubic yard that your experience suggests. (30) 6. — GENERAL MANAGEMENT AND MINING LEGISLATION. 1. You are instructed to negotiate for your Company a lease of a Royalty adjoining your present take. What are the usual principal terms and conditions you would expect to be included in such a lease? (30) 2. Give a brief concise summary of the provisions of the Coal Mines Act, 1911, and of the General Regulations relating to the ventilation of a mine. (25) 3. Certain duties of managers are detailed in the General Regulations as well as in the Coal Mines Act itself. Give the duties of a certificated manager as detailed in both. (25) 4. Describe the principal features of the General Regulations regarding the provision of first aid and ambulance as prescribed by the new Order which came into force on 1st April, 1930. (25) 5. Enumerate the General Regulations which apply when a shot has missed fire. (25) 6. What steps have to be taken before electrical apparatus can be introduced or re-introduced into a mine? (25) * Questions set at Examinations in May, 1930. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H M. Stationery Office, 1s. 6d. net.
|
||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||