|
29th December 1928, Page: 182, Column: 1 Machine Mining — Underground ConveyingBy David Jackson, B.Sc. From paper read at the November meeting of the Past and Present Mining Students' Association in the Wigan Mining and Technical College. Concluded from page 165. Types of Conveyors. Many types of conveyors have been designed and put to work under the varying conditions met with in our coal seams. Careful consideration of face work and of time studies made of face work, gradually revealed that the best results from the fillers on the face and, indeed, from the conveyors, were obtained by conveyors of the continuous discharge class. It may be said that, as the object of a face or gate conveyor is to clear a maximum output per day, a continuously discharging conveyor is essential in most seams. The types of continuous discharge conveyors in service underground are :— (a) The Shaker ; (b) the Band ; and (c) the Scraper Chain. The Shaker. — The shaker is a very robust type of conveyor, and its sphere of application is large. It is simpler, more robust and more flexible in its application than the other types, and it is much used for face and gate conveyor work on all inclinations in favour of delivery; under certain conditions it is used on the level and against low adverse gradients. The success of compressed air shaker engines led to making electrically-driven gears for collieries with electrical power. The shaking action of gears driven by electrical motors is obtained by a link mechanism which converts a uniform angular motion to a non-harmonic motion, which reaches a high velocity and gives a quick reversal of acceleration at the end of the stroke. The numerous flat and undulating seams in this country as opposed to the higher inclined continental seams, together with the more extensive application of electricity at the coal face, have led to higher development of the electric shaker conveyor in this country. The Band Conveyor. — The band conveyor is the only conveyor that can handle large outputs under considerable distances satisfactorily, and has, therefore, a large field of application in conveyor systems underground, especially as a trunk conveyor. The band, which conveys the coal, consists of a high grade textile band, treated with an adhesive compound, and covered with rubber. The textile structure takes the stress of conveying and the rubber acts as a protection against wear of the fabric. The driving gear — electric or air — is usually at the discharging end, and an arrangement for tensioning the band is at the other, or "tension end." Under conditions favourable to it, the band conveyor is undoubtedly much more efficient in respect of power consumption than any other type. It also runs with comparative silence, and this is an important advantage on the faces of certain seams. It may be said that the band conveyor is not as well adapted to withstand coal face usage as is the shaker, and it is much more sensitive to inaccurate setting up, but there are, nevertheless, many cases where its application is very sound economically. The sphere of application of band conveyors on the face is in a system where, by their use, more coal can be collected to one loading point than by using shakers alone. Face conveyor systems, collecting large outputs to one loading gate; include, therefore, shakers for conveying downhill with bands for conveying uphill (or for conveying on the level outputs which could not be dealt with by a shaker). It is good conveyor practice to collect as large an output as possible from each face conveyor system to one loading gate. A conveyor with a large capacity and capable of conveying coal a considerable distance is often required for this loading gate. Band conveyors are very well suited for this work, and as these gate conveyors have heavy responsibility none but the best is good enough. Trunk gate-roads can be made quite as suitable for band conveyors as the coal handling plants on the surface, on which many band conveyors are giving excellent service. Band conveyors with troughing idlers as used in surface installations, are the outcome of many years' experience. Advantage has been taken of this experience, and this type of conveyor has been adapted to underground conditions with very great success. The Scraper Chain. — The scraper chain conveyor consists of an endless chain running in a steel trough, the chain returning underneath the guides. Like the belt conveyor, the driving gear-electric or air — is situated at the delivery end of the conveyor, and an arrangement for adjusting the tension on the conveying member is fitted at the other end. The chain carries and scrapes the coal along the trough, the side plates of which are close to the floor to protect the return chain. The chain itself is usually made to carry coal as much as possible instead of dragging it. The sphere of the scraper chain conveyor for face work is limited, due to :— (a) The difficulty of moving over a conveyor of this type which has its chain positioned properly so that it cannot rise, ride over and break the coal. It is difficult to position a chain properly in a conveyor which has to be split readily and moved over every twenty-four hours ; (b) the tendency to break the coal and increase the percentage of smalls ; (c) the tendency of the chain to break when strong coal, or pieces of strong rock from the roof, get wedged in the conveyor ; (d) the numerous wearing parts ; (e) noisy running; and (f) high power consumption. The scraper chain, however, can be very well adapted for short length units, in which the structure can be built up rigid, and in which there is no necessity to make and break the chain frequently. Such a unit is invaluable for delivering a large output from face conveyors on to a belt conveyor in the direction in which the belt is travelling (which is the only satisfactory way to load a belt), and indeed for delivering the coal into trams from a face producing an output which does not warrant an expensive gate conveyor. It should be added, however, that the probable field of application of the scraper is in the form of a self-loading conveyor which is moved forward as the face advances but which need not be broken up. Loading the Coal into Trams. When the face conveyor, or conveyors in series, deliver the coal to one end of the conveyor panel then the coal can be loaded direct into the trams in the end gate. With such an arrangement, however, it is usually necessary to rip the floor in the loading gate and, if even only a moderately large output is to be loaded, an advance heading is necessary to provide sufficient standage for empty trams behind the one being loaded. Driving advance headings or ripping the floor in loading gateways is usually very expensive and often impracticable. Continuity in loading the output collected, which is essential for good results and imperative when large outputs are collected, can be obtained by use of either (a) a gate-end loader, or (b) a gate conveyor, both of which avoid the necessity for advance headings and floor rippings. Where conveyors deliver coal from both sides of a double unit to a central loading gate either a gate-end loader or a gate conveyor is essential. It is seldom difficult to decide whether a gate-end loader or gate conveyor should be used. The selection depends upon the prevailing conditions. In all cases consideration should be given to the following :— (a) Inclination. — The inclination of a gate-way may not be favourable to the type of conveyor otherwise suitable for handling the output. It may then be more economic to use a gate-end loader and bridge the gap between the main haulage and the loader by some form of auxiliary haulage, (b) Output. — The larger the output to be loaded the greater is the standage required for empty trams, and the more need there is for a permanent loading station. It may be said that outputs over 250 tons per shift should be delivered to the haulage by a gate conveyor conveying the coal to a permanent or semi-permanent loading station, (c) Roof Conditions. — Some roofs do not permit of large finished roadways close to the face. The gate conveyor can convey the coal in a comparatively narrow roadway to a loading point where the roof has settled, (d) Haulage Arrangements. — If the loading point is a conveyor length back from the face the haulage can deliver the trams to the loading point and can be extended at the same time as the loading point is moved forward. If the gradient in the loading gate is unfavourable to loading into trams the output collected to that gate, then a suitable gate conveyor should be employed to convey the coal back to a favourable loading point, (e) Control of the face conveyors. (f) The extent to which conveying is being applied. If a large output is to be collected from a number of face conveyor systems to one loading point then the gate conveyor becomes an essential link between the face and trunk conveyors. Economic Length of Gate Conveyor. — The economic length of gate-road conveyors is determined by the output that is collected to the gate-road. Assuming that the coalfield is uniform and that panels are being worked on either side of the haulage road which is advancing with the developing face, then it is a question whether auxiliary haulage should handle the coal between the panels and the main haulage, or whether a gate conveyor, or conveyors, should do this work. A large output from face conveyors is best delivered to the haulage by a band conveyor. A properly designed band conveyor can convey a large output of coal over a long distance, the distance of course depending upon the prevailing conditions. If the output warrants a conveyor of this type being installed to deliver the coal to the haulage, then full advantage should be taken of the distance to which the conveyor can be extended ; the ultimate length of the panel should be this distance and the coal would then be conveyed during the life of the panel to the main haulage. Laying Out Conveyor Systems. Conveyors are now being applied to collect outputs from 800 to 1,000 tons per day at one loading point. The number of loading points to which trams have to be distributed in a colliery is being reduced to a minimum. Workings are being laid out to get a maximum output with a minimum number of main haulage arteries. In laying out any conveyor system the first essential is that of fixing the length of face unit, whether the coal is hand got or machine cut. If we assume that the seam is machine cut then this unit length depends on (a) the distance the coal-cutter, which is suitable for the conditions, can cut in a shift in the most economic cutting position ; and (b) the maximum length of face conveyor capable of clearing the output with certainty in a shift. Both play important parts in determining the length of unit, and either the one or the other may be the limiting factor. Assuming that a gate conveyor is used to convey and load the coal from a single unit into trams, it is obvious that another face conveyor delivering the coal from the other side on to the gate conveyor will double the output at the tram loading point, and economy in collection will result. The feasibility of the double unit depends entirely on the seam and face conditions. The double unit with its modifications is probably the most economic face conveyor layout. In moderately flat thin seams a double unit with one face conveyor on either side of the central conveyor gate appears from present experience to be the best layout. Indeed, for thick seams from which a large output per yard of face per day can be produced the same layout with, if possible, conveyors in tandem or series on either side of the loading gate, appears to be the best. In other words, the conveyor in the loading gate receives from the faces on both sides of that gate the maximum outputs which the face conveyor organisations can collect. An all-conveyor pit would consist of a number of these intensive face systems interlinked by trunk conveyors, the main trunk conveyor delivering the coal to the output shaft. It may be said that such a system would be possible only in new collieries working thick uniform seams capable of producing high outputs per yard of face per day. Each face panel would require to produce a very high output, and each seam would have to be a system on its own to minimise difficulties in the classification of coal. Many mining difficulties would have to be overcome before such a scheme could be put in operation, e.g., it would be necessary to have the trunk and branch gate-road conveyors in intake airways for ventilation purposes, and thus each face system would have to be a panel constituting an air-split. This, no doubt, would be a determining factor in laying out the face conveyor system in the panel. It has yet to be proved whether an all-conveyor pit is an economic possibility. Longwall Retreating. — Longwall retreating is a method which has advantages in certain seams ; it is probably not adopted in as many cases as it ought to be. The chief difficulty associated with longwall retreating is the time taken to develop the panels. Rapid advance can be obtained by using heading machines of the type appropriate to the seam conditions, and there is scope for further improvement by using conveyors, or conveyor loaders, in the headings. The correct procedure in laying out a conveyor system suitable for longwall retreating is obviously so to adjust the system that the conveyors required for extracting the panel are used in the formation of the panel. No more headings should be driven than are necessary for ventilating the faces and extracting the coal. The dimensions of the panels as far as the conveyors are Concerned should be :— (a) The unit length of face by (b) the economic length of gate conveyor. Loading. — One of the principal advantages of underground conveying is that the handling of the coal by manual power is reduced to a minimum. When the coal is cut and shot down suitable for loading all that remains to be done by the filler is to fill it on to the conveyor, but even this is arduous work. A further reduction in the cost of loading the coal can be obtained only by mechanical loading. Mechanical loading will probably follow on the heels of conveying, but it should be said that the designing of mechanical loaders to suit our seam conditions is a very difficult problem. Experience of loading machines has shown that to get good results it is essential to prepare the coal for loading with the utmost care. While we continue to use the present standard types of face conveyors it seems that much could be done in the proper preparation of the coal for the filler to load, and in procuring for him the shovel best suited to the work he is doing and to the seam in which he is working.
|
|||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||