|
Shap Blue Quarry This quarry has a working face with a length of approximately 300 ft., the height varying between 120 ft. and 140 ft. excluding the overburden. The overburden consists of a 20 ft. thick layer of loosely consolidated stony earth which is removed by a 19-RB face shovel loading directly into two 8 ton Foden lorries that transport the material 200 yd. to the stock bank. Blasting The heading blasting method is usually employed for primary breaking at the Blue Quarry, the pattern being similar to that used at Pink Quarry; 704 grain powder is employed, the yield being from 4 to 4½ tons per lb. Drilling in the mine headings is done with an Atlas Copco RH 57 wet drilling machine taking a 4½ in. by 7/8 in. shank size. Prior to the heading blast, however, the load is lightened to a certain extent by blasting off the top 40 ft. along a 240 ft. line 12 ft. from the edge of the face. Twenty 4 in. diameter boreholes are drilled with a burden of 12 ft. and at 12 ft. centres, by means of a Halco-Stenuick down-the-hole drilling machine. This is supplied with compressed air at 95 lb. per sq. in., the penetration rate being approximately 5-6 ft. per hour. Each hole is loaded with a decked charge of twelve 5 lb. cartons of Opencast Gelignite, threaded on to Cordtex. Charging continues to within 8 ft. of the collar, followed by stemming, a 3 ft. length of Cordtex being left protruding from the hole for fixing to the main line. Initiation is by electric detonator. A typical top blast will bring down from 8,000 to 10,000 tons of well fragmented rock:—
After the product of the top blast has been cleared, heading blasting is performed. Secondary blasting following a heading blast amounts to 40-60 plaster shots daily. For this purpose gelignite is used, initiation being either by Cordtex or safety fuse and detonator in conjunction with plastic igniter cord. Any toe left in the quarry is blasted using gelignite. Loading and transport The broken rock is loaded by means of either a diesel-powered 33-RB, or by a 37-RB driven by a 75 h.p. Mather & Platt 400 V motor running at 970 r.p.m. These face shovels load directly into a fleet of five Aveling-Barford 4½ cu. yd. dumpers which transport the material to the reception chute at the crushing plant. Crushing and screening At the reception chute stone is delivered to a 7 ft. by 4 ft. Hadfield apron feeder which travels at 6 2/3 ft. per min., being driven by a 5 h.p. Metrovick motor through a gearbox. This unit feeds a Hadfield 48 in. by 36 in. primary double toggle jaw crusher, capable of handling 120 tons per hour and giving a -6 in. product. This machine is powered by a 160 h.p. Metrovick motor which runs at 735 r.p.m. and drives the crusher at 150 r.p.m. The crushed material falls on to the 30 in. primary conveyor which is inclined at 12 deg. and is 218 ft. between centres. An electro-magnet is positioned above the belt to remove tramp iron. The conveyor is driven by a 20 h.p. motor and feeds a 60 in. by 42 in. grizzley screen. As may be noted from the flowsheet reproduced as Fig. 24, this unit gives an oversize of + 1½ in. which is passed into a 200 ton bunker. The undersize, -1½ in., is used mainly for hardcore and is stored in the quarry until required for use. The -6 in. ± 1½ in. stone in the bunker is drawn off into Hudson trucks which run on a 2 ft. narrow gauge railway. Trains are made up of sets of 10 trucks carrying a total of 17½ tons and these are hauled by either a 20/28 h.p. Simplex Motor Rail locomotive or a Dorman diesel locomotive to the secondary treatment works. The route involves a ¼ mile length of tunnel running from the quarry floor underneath the main A6 road, and a further ¼ mile of track to the main works. Here the material is dumped into two 30 ton hoppers each feeding a separate secondary crushing and screening plant. One hopper feeds the Kennedy plant producing material mainly for railway ballast, while the second supplies the Nordberg plant which produces a number of grades of stone used mainly in the company’s tarmacadam and concrete plant. Kennedy Plant From the first of the hoppers 30 tons per hour are fed into a Kennedy No. 10 gyratory crusher set to give a product of -2 in., the crusher being driven by a 30 h.p. motor at 970 r.p.m. This -2 in. material is, as shown in Fig. 25, removed from a 30 ton hopper by a 25 ft. Spencer elevator fitted with 20 in. buckets, and powered by a 5 h.p. motor. It delivers on to an 8 ft. by 3 ft. Pegson screen which provides an undersize of -1½ in. The -2 in. by +1½ in. material is fed into a Kennedy No. 19 gyratory crusher giving a product of -¾ in., the crusher being driven by a 30 h.p. motor. The No. 19 crusher delivers stone to a further Spencer elevator also having 20 in. buckets but with centres at 45 ft. and powered by a 7½ h.p. 730 r.p.m. motor. The elevator delivers on to a 28 ft. by 4 ft. Parker Oscillex screen which separates the feed into six sizes, and is powered by a 7k h.p. motor. The rejects are passed to a Parker No. 1 Kubit crusher driven by a 15 h.p. motor. Nordberg Plant The second hopper referred to in an earlier paragraph feeds a plant known as the Nordberg Plant, which produces a number of grades used mainly in the company’s tarmacadam and concrete plant. Stone is fed from the 30 ton reception hopper on to a 24 in. by 48 in. Locker feeder unit. This delivers the -6 in. by +1½ in. material at a rate of 30 tons per hour, into a Pegson 8B gyratory crusher which is powered by a 35 h.p. motor running at 1,460 r.p.m., and which gives a -2½ in. product. This is picked up from a hopper by a 40 ft. centres Spencer elevator having 18 in. buckets and delivered into a 3 ft. Symons standard cone crusher powered by a 60 h.p. motor. The -1½ in. crushed product is fed on to a single deck 8 ft. by 3 ft. Pegson screen which takes out -¾ in. material while the -1½ in. +¾ in. fraction is passed to two Parker No. 3 Kubit crushers which are driven by 30 h.p. motors. Their product, -1½ in. to ¼ in., is taken by means of another Spencer elevator and fed to a 12 ft. by 4 ft. Nordberg screen. This unit sizes the stone to give four products, -¼ in., in., 3/8 in., and kin. The +k in. oversize is passed into a Broadbent rotary screen 24 ft. by 3 ft. 6 in. in diameter which is powered by a 10 h.p. motor. This produces four more sizes -5/8 in., ¾ in., 1 in., and 1½ in. Quarry power Compressed air for the Blue Quarry is supplied through a 5 in. diameter main at a pressure of 95 lb. per sq. in. The compressor which is situated in the main works is a two-stage, four cylinder machine manufactured by Broom and Wade Limited. With a 10 in. bore and 12 in. stroke, this compressor is powered by a 150 h.p. electric motor and has a free air delivery of 600 cu. ft. per min. Acknowledgments The author is indebted to Mr. J. W. Miliray, Resident Director of Shap Granite Co. Ltd., for permission to visit the property and publish this article. In addition he is particularly grateful to Mr. T. A. McGenn, Quarry Manager, for supplying much of the information incorporated in this article, as well as to Mr. T. Coward, Quarry Foreman, for escorting him around the Pink Quarry. Drawings and Photographs accompanying the article
Article reproduced from a copy of the magazine held at National Mining Museum Scotland, Newtongrange, Midlothian.
|
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 17 Jan 2023
|
Search |
|
|||