more of these into a faggot by means of a slender steel rod. One of these fragments is left longer than the rest to serve as a handle; the faggot is then raised to a welding heat in a wind furnace, and is covered with sand, which, combining with a small portion of oxide of iron, forms a fusible slag over the metal, and prevents it from wasting or burning away. When first removed from the furnace it is placed under a forge hammer, which unites all the fragments and closes up internal fissures. The rod thus produced is again heated, the binding rings are knocked off, and the tilt hammer comes into operation, every part of the bar receiving the blows of the hammer in quick succession. As the anvil is nearly on a level with the floor, the workman is seated in a kind of pit excavated for the purpose; he is attended by two boys to bring hot rods and to remove them after they are hammered. By tilting, the Steel is formed into bars of about 1½ inches broad, and 3-8ths of an inch thick; all the loose parts and seams of the blistered Steel are dosed, and it is now capable of being polished, which could not be done before; it is also more malleable, and can be forged with the hammer into shears, edge-tools and cutting instruments. The value of the Steel increases with the amount of tilting it receives; it is, therefore, not uncommon to cut a a tilted bar into several pieces, form them into a faggot, and elongate this again into a bar or rod. The terms double shear, single shear, and half shear, express the amount of doubling and welding which the bars have received.
Cast Steel.
Cast Steel is produced in the greatest perfection by the process of casting; that is, the bars of blistered Steel being broken into fragments, are melted in crucibles, and then poured, while in a fluid state, into ingot moulds. The heat required to produce this fusion is very great, so that the crucibles or melting pots require to be made with refractory fire clay and with the greatest care, in order to exclude bubbles of air and extraneous substances, which might expand or ignite in the furnace, and thus endanger the stability of the melting pot. The crucibles are made of Stourbridge day; a small quantity of coke dust and of fragments of old pots is added, and the whole is kneaded into a perfectly uniform and smooth mass. The clay is first mixed with water, worked up, and then spread out in a thin layer on a shallow trough on the floor. There it is kneaded during 5 or 6 hours by the naked feet of two men, who, with a shuffling kind of motion, or by walking, jumping, or dancing, go over every part of the surface, pressing it down quite flat; and so sensitive is the touch of their feet, that they can, by the difference in the tread, detect an air bubble, a fragment of straw or dirt in the clay. The two latter they pick out with the fingers, and get rid of the air by making a slight incision with a knife. When the whole surface has been well trodden over, it is folded double and trodden out again so as to occupy the whole of the trough. When the clay is prepared, it is made into crucibles, 2 feet in height, weighing about 26 lbs., by fashioning it in a mould having a core to give the internal form. Each crucible is removed as soon as it is finished into a heated vault, where it gradually becomes dry; and some hours before being used the crucibles are brought to a red-heat for the purpose of annealing them. A crucible can seldom be used for smelting the steel more than three times without cracking; so that there is a constant demand for crucibles, as many as 108 being required per week for a ten-hole furnace.
On a level with the crucible-making department are the furnaces for melting the Steel; these are ordinary wind furnaces placed in connexion with a tall chimney by which a strong natural draught can be obtained. Each furnace is only just large enough to contain two crucibles and a proper amount of fuel; and it is lined with a plaster calculated to resist the intense heat. This plaster is formed, in the works at Sheffield, of the dust of the roads in the vicinity of the town, and is called ganister. The fuel employed is a dense well-made coke, broken into lumps of about the size of a hen's egg, Immediately over each furnace is a trap-door, made of fire bricks, fastened in an iron frame opening into the casting house, which is a kind of shed entirely open on one side, while on the other, ten trap-doors are seen, from the sides of which escape a few rays of red light indicative of the fiery furnace below. In an adjoining shed the bars of blistered steel are broken into fragments, and the charge for each crucible, about 30lbs., weighed out in tin trays, a small portion of black oxide of manganese being added to each charge, this substance being supposed to improve the quality of the Steel. In some cases powdered charcoal forms part of the charge. The empty crucibles are put into the furnace upon a sole of baked fire clay, and the charge is given to each by means of a long funnel of iron plate. Each pot is carefully covered over with a lid of a more fusible clay than the body of the crucible, and sometimes a small quantity of bottle glass or blast furnace slag is put in above the steel fragments, so as to form a sort of vitreous coating to prevent the air from oxidizing the metal. When the pots are thus charged and covered in, the furnace is filled up with coke and kept well supplied. In about 4 hours the Steel is in a state for casting, and as the time approaches the men occasionally lift up the various trap-doors and examine the crucibles, their eyes being accustomed to detect, through the fierce floods of heat which pour upwards from the furnace, the precise time when the metal is sufficiently fluid for casting.
While the Steel is melting, the ingot moulds are prepared. These moulds, which are of cast iron, are of various sizes according to circumstances. Previous to putting the moulds together, the interior is smoked by being laid across a pitch fire, time internal coating of carbon thus imparted preventing the liquid Steel from adhering to or melting the mould. Just before drawing the crucibles each man puts on sacking leggings, and an apron of the same material thoroughly soaked with water, as a further protection to the fierce heat to which he is about to be exposed; then throwing open the trap door of one of the furnaces, lie removes a portion of the white hot coke, and, planting his feet one on each side of the yawning fiery furnace, thrusts down a pair of tongs furnished with concave jaws for grasping the crucible just below the swell, and then, with a motion between a jerk and a swing, raises the glowing burden. A second man immediately removes the cover; a third man, and the most skilful, grips the crucible with tongs held horizontally, raises it, and slowly inclines it to the mouth of the ingot mould, his attendant with a pair of tongs removing any portions of cinder or slag from the surface of the molten metal.
Considerable skill is required in teaming, as the operation of transferring the metal from the crucible to the ingot mould is called. It must be poured directly down the centre of the mould, without touching the sides; for were it to do so, it would instantly remove the carbonaceous covering, and burn a piece out of the mould. The metal flows as liquid, and with time same gurgling sound, as water ; but the extremely high temperature of the molten Steel is shown by the white heat slightly tinged with blue. As the stream falls, minute portions of it combine rapidly with the oxygen of the air, and take fire, producing brilliant scintillations. The fire even communicates itself to the ingot towards the end of the process of teaming, and the mould then appears like a brilliant fire-work, but this combustion is soon stopped by the insertion of a solid plug. As the ingot immediately solidifies, each mould is opened directly after the teaming, and the ingot is turned out in a red-hot state. This rapid cooling of the Steel and the thin film of soot effectually protect the mould from the destructive action of the liquid metal which would otherwise ensue.
As soon as the crucible is emptied of its contents, it is returned to the furnace, to receive a fresh charge; and as 4 hours are required for the melting, there are three casts in the 12 hours during which the men work. The charge is introduced by means of a funnel of plate iron, into which a rod is inserted to break up the charge, and prevent a heavy mass from falling at once into the crucible, which might cause its fracture. Cast Steel is much harder and denser than tilted Steel, but it requires care in forging, because a little above a cherry red heat it is very brittle. Two surfaces of cast Steel may be welded together by interposing a thin film of borax; and cast Steel may be firmly united to a polished surface of Iron by placing the Iron in the mould into which the Steel is poured. The two metals can then be rolled and worked out together into rods adapted for forging. When Steel is moistened with a drop of dilute nitric acid, a dark grey spot is produced; malleable Iron so treated yields a spot of a green colour,
Please Note: These web pages retain the original pagination from the publication