gearing from the engine; 1,300 revolutions per minute is not too great. In Staffordshire, a single bench with a saw at each end, cutting both ends of the bar simultaneously, is very generally used. In the Welsh mills two saws are mounted on a spindle about 4 feet long, and a bench provided at the outside of each. The inside bench is usually placed at a distance of 25 or 30 feet from the rolls, in a line with the finishing groove. The bar having been drawn on to the bench, with one end projecting beyond the inside saw, it is firmly held in its position by a suitable apparatus, while the bench is moved laterally until the saw has penetrated and completely divided the projecting end, when it is drawn back sufficient to allow the bar to be drawn lengthways on to the outside bench, which is provided with an apparatus for adjusting the length. The forward movement of the outer bench against its saw completes the cutting of the bar, which is withdrawn to the hot filer. Saws worked by an emission engine on the same spindle have been erected, and under certain circumstances are superior to those driven by belt and gearing. Where the saws are constantly at work, the latter mode is preferable, though expensive, if the saws should be situated far from the engine; but where they are only occasionally used the steam saw is probably the cheapest. The saws are furnished with coarse teeth on their edge, which are sharpened after 12 or 24 hours' working, according to the number of cuts made. Steel saws will cut from 600 to 700 bars before sharpening; iron saws will not cut more than half of this number. To prevent the teeth from heating and softening, the lower edge of the saw works in a bosh containing cold water.
Devices. — Figured devices on the surface of the iron bars of varying width, and bars with countersunk holes on the surface, are produced by letting in the rolls at the finishing or last groove, corresponding steel dies and punches. Trade marks are produced in a similar manner, though the older mode of hand-stamping is most commonly followed. — Truran.
The business of the Iron-maker here ceases. From the raw ore the workman has conducted the metal through the various and difficult processes which have been described, until he has produced bars and sheets of Iron of the various qualities and shapes required; these now pass into the hands of others, who fashion from them the countless articles of every-day life, from a nail to a steam engine, a suspension bridge, or a ship of war.
Chapter V.
IRON AND ITS MANUFACTURE IN FRANCE — NUMBER OF FURNACES, HOME PRODUCTION AND IMPORTS. THE CATALAN FURNACE, ETC. DESCRIPTION OF THE MARQUISE IRON WORKS AND THE WORKS OF THE MONTATAIRE COMPANY. THE IRON OF OTHER COUNTRIES — BELGIUM, PRUSSIA, SWEDEN, RUSSIA, AUSTRIA, SPAIN, AND AMERICA.
Iron And Its Manufacture In France.
The manufacture of Iron was known in France at an early period. The warlike nations of Gaul were well armed, and 370 years before the Christian era, from their early practice of mining, they were familiar with the uses of metals. The processes were carried on with portable furnaces and forges, and were worked by manual labour or beasts of burden. Caesar, in speaking of some of their operations in warfare, says :— "They took down our embankment by mines, the more scientifically, because they have great Iron works, and every kind of mines known and in use."
Iron ore is found in abundance in France, particularly in the north-eastern departments; and towards the end of the last century the French Government took active measures to become acquainted with the state of the mines, and also to introduce any improvements which might facilitate their working; and encouragement was given to the establishment of Iron works for the use of coke instead of wood. In 1801, about 140,000 tons of cast Iron was produced throughout the country; one single blast furnace, that of Creusot, being worked with coke. In 1809, the first blast furnace wherein the minerals were treated in the same manner as in England, and the third in which coke as employed, was erected near St. Etienne. In 1820, extensive works were erected at Fourchambault and Hayange, which have served as models for those which have since been built; and an increase was soon experienced in the number of Iron works wherein pit Coal was employed. In 1828, the number of blast furnaces upon the improved construction had increased to 14, and that of forges on the English plan to 40. A paper was read in 1831 before the Society of Sciences and Industry, in which it was stated, "that the want of means of transit and communication is more grievously felt by our Iron manufacturers than by any others; thus, at Fourchambault, at St. Etienne, Hayange, and other Iron works where the cast Iron is made with coke, the expense of carriage alone amounts to one-third, if it be not nearer one-half, of the total cost of manufacture, so that the ton of metal is charged 60, 70, or 80 francs for the cost of transport only." In 1836, coke was almost exclusively employed for processes subsequent to smelting the ore. The average prices of the different kinds of fuel in 1836 were :— Wood charcoal, 54s. 10d. per ton; Coal, 188. 5d. per ton; coke, 20s. 3d. per ton; wood, 2s. 10d. per stere; during this year there were manufactured 303,739 tons of pig Iron, and 201,691 tons of malleable Iron. The total make of charcoal and coke pig Iron in 1847, was 591,590 tons; in 1848, 473,442 tons; in 1849, 414,195 tons; in 1850, 405,653 tons; in 1851, 445,808 tons. There were in 1852, about 75 blast furnaces in France; and the production of Iron was — pig Iron, 522,643 tons; of malleable Iron, 301,803 tons. In 1855 England exported to France — pig Iron, 78,201 tons; bar Iron, 60,730 tons; bolt and rod Iron, 303 tons; cast Iron, 1,178 tons; Iron wire, 22 tons; anchors, grapnals, &c., 568 tons; hoops, 1,637 tons; nails, 32 tons; other sorts, except ordnance, 4,259 tons; old Iron, 87 tons; unwrought Steel, 456 tons. The quantities exported in 1856 were — pig Iron, 84,923 tons; bar Iron, 70,490 tons; bolt
Please Note: These web pages retain the original pagination from the publication