Brief Description Of Mine And Method Of Working
4. The Burngrange mine is relatively new, having started production in 1936. There are two vertical shafts, each 14 ft. in diameter and brick lined throughout. No. 1 shaft is used for winding men, minerals and other materials. No. 2 shaft is used for ventilation and pumping. Both shafts are sunk to a depth of 468 ft. to work the Dunnet Shale Seam, which varies in thickness from 9 to 12 ft. The dip, of the seam in the No. 2 district of the mine is variable, averaging 1 in 5 in a north-westerly direction. The mine is ventilated by a double inlet Sirocco exhausting fan passing about 100,000 cubic feet of air per minute at a water gauge of 0.95 in. All workings are in the Dunnet Shale Seam. The average daily output of shale over two winding shifts is 600 tons. The number of persons employed is approximately 29 on the surface and 176 underground; giving a total of 205 persons.
5. The method of working is stoop and room. The size of the stoops varies according to the depth, but in the area affected by the explosion, the stoops are formed approximately 150 ft. by 110 ft. by driving rooms 12 ft. wide and 9 ft. high on level course and at right angles thereto. Where the seam exceeds 9 ft. in height, the top shale is left to form a roof. In the second working, when the stoops are being extracted, splits are first driven through each stoop to form small pillars which are then extracted by taking off lifts 12 ft. wide and the full height of the seam. Pillar extraction is generally arranged so as to form and maintain a main roof-fracture line at an angle of about 45° to the levels.
6. Plan No. 1 shows the lay-out and full extent of the underground workings, the general direction of the ventilation and the quantities of air passing in each ventilating split. The disaster was confined to one ventilating split which ventilated part of No. 3 District and the whole of No. 2 District. The latter District comprises two sections of workings, one in which the pillars were being extracted and one to the east of it where the large stoops were being split into small pillars. From Plan No. 1 it will be seen that an area of fully three acres of shale has been completely extracted to the north-east of a middle dook which, although sometimes known as the 40 H.P. dook, will be referred to hereinafter as No. 2 dook. Extraction of the stoops in this area commenced in November, 1945, and was being continued on the west side of the area. From the inbye ends of Nos. 10 to 14 Levels — see Plan No. 1 — and to the east of the stooped area, the stoops were being split into pillars. These pillars were to be left to avoid subsidence and damage to a housing scheme on the surface. It was in this section of the workings that all but one of the 15 victims of the disaster lost their lives. Preparatory splitting of stoops prior to extraction was also proceeding in the No. 3 District on the outbye or west side of the extraction area.
7. The shale is got by blasting, and is hand-filled by the miners into 20-cwt. capacity hutches which are hand drawn for relatively short distances by drawers to a subsidiary mechanical haulage. Thereafter, the hutches are hauled by Diesel locomotive and main rope haulage to the shaft bottom. The explosive used is compressed gunpowder fired by fuse. The holes for blasting are bored by electrically operated drilling machines. All underground machinery is electrically operated.
8. A mixed system of lighting, comprising open lights and safety lamps, is in use underground. Although firedamp was of rare occurrence, its presence was not unknown and, in consequence, certain precautions were taken. It was customary for the miner at the working face to use an approved electric safety cap lamp and to be provided with an approved flame safety lamp which was hung up near the working face. The drawers, who carried these flame safety lamps in and out of the mine, and the other outbye workmen used open acetylene cap lamps. Rules posted at the mine regarding the use of safety lamps were as follows
"FACEMEN IN CHARGE OF PLACES SHALL USE ELECTRIC CAP LAMPS.
FLAME SAFETY LAMPS SHALL BE KEPT IN WORKING PLACES.
BEFORE ENTERING PLACES AT THE COMMENCEMENT OF WORK AND BEFORE AND AFTER SHOT-FIRING, THE FACEMEN SHALL TEST FOR THE PRESENCE OF GAS."