|
15th May 1943, Page: 271, Column: 1 Some Aspects Of Mine Dust SuppressionFrom paper read at the April meeting of the Wigan Mining and Technical College Past and Present Mining Students' Association. Continued from No. 22, page 254. By W. Staton, B.Sc.(Hons.), H.M. Inspector of Mines. Loading Points. The air cleaning done underground has been small and mostly confined to the conveyor loading point, where, at some mines, the cloud of dust which arose when the tub was being filled became quite intolerable, and the dust collector just had to be. All dust extractors at loading points are basically the same. They consist of a cowling built over or behind the tub into which the dusty air is induced to flow, advantage being taken as far as possible of the momentum imparted to the dust particles by the ventilating current, the air then being passed through a dust separating unit. To the best of my knowledge, with the exception of the Mavor and Coulson dust extractor, the air is always induced to flow by means of a small (12-inch or 16-inch diameter) auxiliary fan. The Mavor and Coulson dust extractor exhausts the air from inside the cowling by means of a static blower, which consists of two truncated cones joined at their smaller ends, with a compressed air jet fixed near the point of least area. Water is fed to the jet, which thus, in addition to causing air flow, acts as a mist projector. As the dusty air passes through the throat the dust particles are wetted by the mist and the air is given a swirling motion which is emphasised by fixed vanes inside the collecting tube, and the particles are deposited by centrifugal action and impingement. With the Meco dust extractor the dust laden air enters the separating unit tangentially, and then into a mixing tube into which a water spray is directed, the dust being removed by scrubbing and vortex separation. In the Huwood dust extractor the dusty air is passed through a series of fabric tubes, the dust being separated by dry filtration. Many other dry filters have been used, constructed of such materials as sawdust, glass wool, met-wool, coal, packwalls, etc., and recently the true centrifugal separator has been employed. The most troublesome factor in connection with the effective suppression of dust at loading points seems to be the limited power available for dealing with the quantity of air into which the dust has become disseminated, and to overcome this we can increase the power by installing larger and higher pressure fans, or we can reduce the pressure drop across the filter by increasing the area of filtration (e.g., we could increase the number of fabric tubes, thereby providing a larger filtering area and a reduced filtration velocity), or we can reduce the pressure drop and velocity of filtration by reducing the quantity of air to be cleaned. Limitations of space make it difficult to increase the size of fans or filtering units and therefore attention must be directed towards reducing the quantity of air to be cleaned. This can only be done by collecting the dust before it has had time to become disseminated into a large volume of air — the dust should be collected as near to the point where it is being made airborne as is practicable. Again, it becomes a question of prevention of dissemination, and I regard this as axiomatic. Much has been done already in this direction by constructing cowlings over the loading points, but a cowling may restrict the freedom of activity of the loading lad, and is not always welcome on that account. A similar problem arose in metalliferous mines when tipping ore and waste into the chutes. After each tub was tipped a cloud of dust arose from the chute, and it was required to suppress this dust whilst still allowing freedom of tipping. The trouble was overcome by withdrawing air from the bottom of the chute, thus causing it to downcast. If it is necessary to fill tubs from an open stream of coal, I suggest that, whilst a tub is being filled, dusty air should be withdrawn from the bottom or bottom side. Sprays, of course, are being used at loading points, over the belt and over the tub being filled. These almost certainly scrub some of the dust from the air, but they are probably more effective in preventing the dust from becoming airborne. Occasional glances have been thrown towards conveyor transfer points, but as yet the problem has not been approached seriously. What I have said about loading points applies equally well to transfer points. Before leaving this subject I would like to refer briefly to the means for providing a suction for withdrawing the dusty air for cleaning. If there was only one power-driven machine underground it might be possible and economical to provide it with its own compressor or generator, but as the number of power-driven machines increases it is usually more convenient to have a supply common to the mine or a district in the mine. Similarly, whilst dusty air is being collected at only one point in the mine or district it is probably permissible to create the suction at that point, but when you have a number of points where dusty air is being withdrawn then surely a suction system and air-cleaning unit, common to the mine or a district, would be advantageous ; and I suggest that a number of points where dusty air should be withdrawn already exist. I have already mentioned kirvings, transfer points and loading points, and there is the dust which is retained on the empty belt and that which accumulates at belt rollers. If we had a suction main of adequate power which was easily tapped, we might even clean up some of the road dust. In Roadways. A few attempts have been made to take out the dust from the air passing along roadways, notably at the point where the air leaves a face which is being mined intensively. This has been done mainly by means of mist projectors and water-sprays (these are the same of course, but for convenience I speak of a spray which uses compressed air and water as a mist projector, and of one which uses water alone as a water spray). In effect, the roadway is being turned into a rather inefficient scrubbing tower. It is obvious that the finer the particles into which the solid water is formed the greater is the number of particles present in the air, and the greater are the chances of collision between the water and dust particles, with a consequent wetting of the latter and a greater settling and cohesive effect. A great deal of attention has been paid to breaking down solid water into the finest possible particles. By warming and saturating the air, and then by subsequent cooling, tentative efforts have been made to cause the moisture in the air itself to condense on the dust particles, but so far with little practical success. A point not always so well realised is that the number of particles present in the air can be increased by increasing the size of the spray and the quantity of water used, and it may be an advantage to have a percentage of larger particles present to act as "gatherers" and thus precipitate the finer particles of moisture before they are blown away by the air-current. This of course is the big drawback to the open spray. There is no easy method of collecting the dust which has been precipitated. It has been merely deposited over a shorter length of roadway. The other method which has been tried in an effort to take out the dust from the general ventilating current is that of placing baffles at an angle to the direction of air-flow and alternately on opposite sides of the airway. The air-current is forced to change direction suddenly, and the inertia of the dust particles causes them to be deposited on the baffles. In this case the baffles may be treated by water or some form of adhesive which helps to retain the particles deposited. As a modification of this I should like to see the effect of a length of brattice cloth looped across the roadway so that there are a number of vertical sheets, parallel to the airflow, which are kept moist by means of water sprays. This, in effect, would be a streamline filter and scrubber. The sheets could be made to concertina to facilitate the passage of men and materials, and the number of vertical sheets could be so arranged that the quantity of air passing along the face was not reduced below the necessary minimum quantity. This last-mentioned feature illustrates the difficulty of cleaning the general ventilating current. With the exception of gravitational settlement air cleaning implies that work must be done and energy expended in some form or other, and for the present we are trying to clean the air, either by the expenditure of energy in breaking up water, or by utilising the power capacity of the ventilating fan. There is a limited ventilating pressure across a coal face and its primary function is to cause air flow. If, after it has caused a sufficient flow of air, there is a reserve of pressure then this may be used to clean the air. But surely it would be more satisfactory to provide an auxiliary source of power sufficient to overcome the resistance of an air cleaning plant which could deal effectively with the whole of the air leaving a face, and before it entered the main roadways of the mine or another district. To recapitulate, the main lines of approach to the suppression of coal dust are : (1) Prevention of formation, (2) Prevention of dissemination, and (3) Air cleaning. (To be continued).
|
|||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||