|
6th February 1943, Page: 186, Column: 2 Rock Bump At Barnborough MainCause of UpheavalCmd. 6414, H.M. Stationery Office, price 9d. net. Brief reference was made in No. 15, page 170, to the official Report issued by the Ministry of Fuel and Power on the causes and circumstances attending the upheaval of floor which occurred on 24th April, 1942, at the Barnborough Main Colliery, South Yorkshire. At this colliery, which is owned by Manvers Main Collieries, Ltd,, two seams are worked, the Barnsley Bed, 6 feet of which is extracted, at a depth of 510 yards, and the Parkgate seam, 5 feet thick, 250 yards deeper. The Barnsley Bed was reached in 1914, and was opened out in that and the following year. From the beginning of 1916 the annual output has averaged about 460,000 tons. The system of work has been by advancing longwall panels formerly filled into tubs, but latterly on to conveyors. The Parkgate seam was commenced in 1928, but little was done except development until the latter part of 1937, since when the annual output from this seam has been about 430,000 tons. It has been worked in a variety of ways, viz., advancing longwall by hand, advancing longwall machine holed and conveyor filled, retreating longwail, and bord and pillar. The inclination of the seams is 1 in 28. Major H. J. Humphrys, D.S.O., O.B.E., M.C., H.M. Divisional Inspector of Mines, is responsible for the preparation of the report. The following abstract is made from the section discussing the cause of the upheaval. The cause of the sudden upheaval of the floor was a rock bump. Fundamentally these bumps are of two kinds, viz., pressure bumps and shock bumps ; both are due to the action of the weight of the strata superimposed on the coal seam or to the enormous lateral or tangential stress due to structural or tectonic folds and thrusts, and sometimes to both. Pressure bumps occur when a group of coal pillars or small areas of coal bounded, or partly bounded, by waste suddenly fail on becoming overloaded by the weight of strata above them. Generally, the coal breaks up rapidly and is forced with some violence into roads and open spaces, but sometimes the floor at the working face bursts. With this type of bump the greatest damage and violence usually occur near the boundaries of the group of pillars. Bumps of this kind are fairly common. They have occurred in India, Canada, United States, France, Germany, and in this country in South Wales, Scotland, Lancashire, South Staffordshire and Yorkshire, and have caused loss of life and serious personal injury. One at Pendleton Colliery, Lancashire, on 4th November, 1925, resulting in the loss of five lives, was the subject of inquiry by a departmental committee. Shock bumps occur where a thick, strong massive stratum like sandstone, lying immediately above and extending beyond a group of coal pillars, is severely strained near the centre because the overhanging parts subside and bend downwards over the wastes. The centre part over the coal pillars is thereby deflected upwards into the form of a shallow dome. If a large mass of the order of thousands of tons suddenly breaks off the overhanging parts, as it is most likely to do near the abutments on the boundaries of the group of pillars, that part of the thick strong beds which had been deflected upwards descends suddenly and strikes a gigantic hammer-like blow on the beds below. The tremendous energy of this blow is transmitted to the coal pillars and the floor. The shock passes through the surrounding rocks, often over considerable areas, like an earthquake wave. With a bump of this kind the greatest effects of violence are usually well within, rather than at the boundaries of, the group of pillars. Shock bumps have occurred fairly extensively in Canada and the United States. They have not hitherto been definitely identified as occurring in mines in this country, but there seems little doubt that the subject of this report falls in this category. The factors contributing to the bump were probably : (1) The great depth at which coal was being worked on the bord and pillar system, viz., 760 yards. (2) The absence of waste packs in pillar extraction workings. (3) The occurrence of strong sandstone beds varying from 8½ to 54 feet in thickness, with a total thickness of 115 feet, immediately overlying the seam. (4) The coal seam and the floor were strong. (5) Coal has been extracted all around the pillared area, except the short length adjoining the shaft pillar. (6) On the south side faces had been advanced in opposite directions. (7) The small pillars of coal at C and D tended to create conditions conducive to a pressure bump which would precipitate a shock bump. Pillar C, where it was possible to examine it, bore evidence of severe crush. (8) The extraction of surrounding coal had been so recent that the upper measures, at least, would still be moving. It is to the combination of circumstances and natural conditions rather than to any single one that the occurrence is attributed.
|
|||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||