12th December 1942, Page: 134, Column: 2
Power Loading Underground
Types of Loaders
Extracts from paper presented at the October meeting of the Manchester
Geological and Mining Society. The paper was illustrated by a series of slides.
By W. H. Richards, M.I.M.E.
American Jeffrey Self-Loaders.
My first experience was with the American Jeffrey self-loaders at the Cannock
Chase Colliery. They were of a maximum length of 40 yards and consisted of
sections 10 feet in length joined together by a stout male and female coupling.
"Flight-arms" at 18-inch centres were fastened to a heavily built
chain working in a channel and which was driven by a 30 H.P. electric motor and
gear at the discharge end of the conveyor. These "flights," which
worked on steel plates, carried the coal along to the discharge end, where they
were turned from a horizontal to a vertical position, returning under a
V-shaped cover plate to the tail-end of the conveyor, where they again assumed
a horizontal position.
One of the features of this conveyor was its flexibility ; it worked quite
satisfactorily in any reasonable broken line. After the coal was cut the
conveyors were pushed forward by "Simplex" jacks into the scuftings.
When these were loaded out, the coals were blown on to the conveyors, and
loading proceeded. At least 95 per cent. of the coal was mechanically handled.
After the face had been cleared, the colliers "jacked" the conveyors
back from the face, leaving just enough room for the coal-cutter to pass along
and cut the face.
Two back ranks of props were now knocked out, "falling-up" the roof.
The only pack put on was a 3-yard, forming with the side of the pillar the
airway from the next pair of pillars either working or to be worked.
To control any "weight" thrown forward into the gate road, a double
rank of steel props were set, one on each side of the gate conveyor, for a
distance of some 15 yards from the edge of the retreating face.
The system of working consisted in opening-out with arc-wall machines to an
arbitrary boundary, forming pillars 40 yards wide and which, were brought back
in pairs. The width of the arc-wall headings was fifteen feet.
The coal in the pillar extraction was machine holed in the bottom of the seam
to a depth of six feet, shot down and loaded off by the self-loading conveyors
on to a Jeffrey sectional scraper gate conveyor. The troughing of this gate
conveyor was in standard sections of six feet, being equal to the depth of
undercut. This meant that at the end of the coaling period the conveyor was
shortened by a 6-foot section. The maximum length of the scraper conveyor on
the level was 120 yards, so 26-inch Mavor and Coulson rubber gate conveyors
were mounted in tandem, these in turn delivering the coals into ten-cwt. tubs
at the loading point.
The forming out of the pillars with the arc-wall machines was economically
done, as two men on one machine would cut an average of twelve heads per shift,
including "flitting" time.
The Duck-Bill Loader.
This loader is used for heading work and pillar extraction. It is fixed to the
face end of a shaker conveyor and digs into the coal with its head, which is
made in the shape of a shovel.
The shaking motion of the conveyor causes the coal which has fallen on to the
shovel end to slide into the troughs and to be conveyed to the delivery end,
where it is either discharged into a tub or on to a gate conveyor. The feed is
obtained by means of a ratchet device which is actuated by the motion of a
jigger engine which, through a toothed wheel and rack, pushes the shovel trough
forward. This trough is guided by another one embracing it. After extending the
trough its full length, or when it reaches the back of the cut, it
automatically slips, thus preventing damage to the duck-bill or conveying
troughing. A throw-over lever is now operated, and the duck-bill automatically
retracts itself to its starting position. While the duck-bill is retracting, a
bar is slipped under the end of it, sliding it into a new position preparatory
to feeding it into the coal again. It should be understood that the duck-bill
has a swivel connection at its rear which enables it to arc across the face.
Thus the loading movement is a cycle of movements in which the duck-bill is
advanced into the coal, retracted, moved three feet or so angularly in a
horizontal plane, and then fed into the coal again.
After all the coal has been loaded out to the full extension of the loader, it
is retracted, and another standard jigger pan inserted, and the duck-bill is
operated again as before. It is essential that the coal shall be properly
prepared to get efficiency.
The Eimco-Finlay Loader.
This machine will allow of speedy removal of debris from level tunnels or
tunnels with little gradient, thus enabling a much more speedy development. In
action, the loader is virtually a mechanical robot, combining all the
flexibility of hand shovelling with the inexhaustible energy of a power driven
all-steel machine. It responds completely to every desire of its operator
— eating into the muck pile in every direction, loading, elevating and
discharging with amazing speed and precision.
This loader has only two motivating functions, loading into the bucket and
discharging into attached tub, the power for which is furnished by two
Ingersoll-Rand air motors. One of these motors furnishes power for propelling
the machine and thereby crowding or pushing the bucket into the imick pile. The
other motor furnishes power for elevating and discharging the debris into an
attached tub. Convenient control valves permit the operating of either motor as
rapidly or slowly as desired, separately or simultaneously.
Air supply, for both motors, is secured through a flexible hose, usually about
50 feet long, connected to the same air range, that supplies the drilling
machines. The consumption of compressed air is light, requiring only the same
amount as for a "jack" hammer.
This machine, when side digging, will automatically align itself for
discharging into the tub. The headroom required varies according to the height
of the tub, being between 72 inches and 83 inches. The working radius is seven
feet, so that for a 15-foot tunnel a double working tub track is needed.
The Huwood Buttock Loader.
This loader is made by the Huwood Mining Machinery Ltd., of Gateshead-On-Tyne.
It consists of a train of enclosed gears which work five "flight"
arms operating in unison, and which are secured to a stout
"flight-bar" and driven by a totally enclosed 10 H.P. electric motor.
The flights move in a circular path, breaking into the coal when in their
extended position and being almost hidden inside the loader casing in their
retracted position.
The method of propulsion is by two haulage ropes attached to separate drums and
fitted with multi-plate clutches. These drums can operate either separately or
together, as the operator desires.
One of the ropes is laid at the back of the under-cut and the other between the
face and the face rank of props. The undercut rope is laid by the coal-cutter,
while cutting operations are in progress by means of a trailer bar or threader
bar fitted behind the coal-cutter jib. This bar is of 2-inch diameter steel and
secured at one end to the turntable of the coal-cutter and cranked in such a
manner that it is lying under the undercut parallel to the coal-cutter jib, but
clear of it by 3 to 4 inches.
At the extreme end of the bar a punched or drilled hole receives the loop or
eye of the haulage rope. The rope is "paid out" as the cutting
proceeds from a loose coil of rope lying on the face. The gob side rope is laid
after the cutting is completed.
The Huwood loader is made in two sizes, one 5' 4" long and the other 6'
6" long. They are both 3' 6" wide and 1' 9" high. The smaller
machines are in operation at the Manchester Collieries, and are capable of
loading, under suitable conditions, 50 to 80 tons per hour.
Conclusion.
In conclusion, while I know I am preaching to the converted, it may be as well
to say that for any system of working to be successful it is essential that
there shall be :—
1. Optimism, realism, enthusiasm, confidence, and co-operation.
2. For the first experience in mechanical loading, the best natural conditions
possible.
3. With mechanical loading, it is absolutely essential that the coals shall be
properly prepared, remembering that the machine is ostensibly a loader and not
necessarily a getter.
4. That as there is no one method of working, system of conveying, or type of
loader that will suit all and any conditions I feel confident that we shall
have to find the system and the loader, if we are to survive. Mechanical
loaders are here — they have come to stay.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Richards, W. H. | | Mining Engineer | |