|
16th May 1942, Page: 315, Column: 2 Production Of Carbon Monoxide In Compressed Air RangesIn his study presented at the April meeting of the North of England Institute of Mining and Mechanical Engineers, to which reference was made in the last issue of this journal, Mr. W. B. Brown, H.M. Inspector of Mines, spoke of the interesting and profitable time devoted to looking up reports by Divisional Inspectors on cases in which carbon monoxide was produced in compressed air ranges. Appended are extracts from the paper. At a Cumberland Colliery, in 1927, a compressor attendant was burned by an ignition of vapourised oil in a crank chamber of a twin stage, electrically operated vertical type compressor, taking 3,000 cubic feet of free air per minute and compressing it to 80 lb. per square inch. The heating was attributed to the failure of the attendant to turn on the circulating water when starting up the compressor. The compressor had been running light for a time when an explosion occurred, which blew off the crank-case door, the attendant being burned as he was attempting to open the switch. At a Yorkshire Colliery, in 1925, a compressor-air range in the downcast shaft was wrecked as the result of an explosion in a surface compressor. There was no loss of life, as men were not riding the shaft at the time of the explosion. Following previous trouble, air-filters had been fitted on the inlet side and were in use at the time of the explosion. The shaft-range was of steel, ¼-inch thick and 12 inches in diameter. It was found that the pipe-range had badly corroded and a minimum thickness of 1/32-inch was found after the explosion. The range was being gradually replaced and the damage was confined to the old pipes in the range from a point 25 yards from the shaft top to a depth of 425 yards in the shaft, 450 yards in all. Extensive damage was done, and the shaft remained idle for a week. The point of origin of the explosion was not located, but a flash was observed at one of the relief valves of one of the electrically-driven compressors. Recorded temperatures were 320°F. between the first stage and the intercooler and 280°F. at the delivery of the second stage. The flash-point of the oil in use was guaranteed at 410°F., and a sample tested gave 450°F. The cause of the explosion was not stated, but attention was drawn to the following points :— (1) The existence of six right-angle bends in the delivery range between the compressor and the shaft top. (2) The fact that the recorded temperatures, in the presence of oil-vapour and coal dust, are dangerous. (3) The necessity for cleaning inlet air by filters. (4) The question of whether or not men should be allowed to ride in shafts in which compressed-air mains are installed, when the compressors are in full work. At a North Derbyshire colliery, in 1925, two men and a deputy were overcome and slightly gassed by fumes from an air-compressor used to operate a heading-machine. The symptoms pointed to carbon monoxide poisoning. The compressor had heated-up following a breakdown of the oiling system. The attendant adjusted the oil-feed to give an increased flow and the resultant gases overcame the men. At a large Durham colliery, in 1927, an explosion of vapourised oil and probably coal dust occurred in a compressed-air delivery range, 18 inches in diameter between the compressor and the receiver, situated near the top of the downcast shaft. The range was found to be badly corroded. Flame and sparks were seen at the time of the explosion. Some of the fumes exhausted from a compressed-air engine driving an endless-rope haulage set situated in the downcast shaft-bottom, and the hauler attendant was overcome. An overman who rescued the attendant collapsed, and five other persons in the shaft siding were also affected. The attendant remained unconscious for 17 hours. The cause of the explosion appeared to be frictional heat generated in the delivery range due to the presence of four right-angle bends in a short length of delivery range hear the compressor. The inlet air was not filtered and in this way coal dust was admitted into the compressor, necessitating a larger supply of lubricating oil. Following this accident the bends were removed and filters fitted to clean the inlet air.
|
|||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||