|
2nd May 1942, Page: 303, Column: 2 Mechanisation And Falls Of Ground AccidentsExtracts from paper read at the April meeting of the Manchester Geological and Mining Society. By A. Winstanley, M.B.E., D.Sc, H.M. Inspector of Mines. The use of machinery for cutting, breaking down, conveying and loading coal at working faces has been increasing for many years, and has continued to increase since the outbreak of war. In 1940, the last year for which figures are available, 64 per cent. of the total coal output was cut by machines, and 61 per cent. was conveyed, whereas in 1930 only 31 per cent. was machine cut and 17.1 per cent. was conveyed.Accident Risks. By the law of averages, the number of accidents over a sufficiently long period (annually) and over a sufficiently wide area (in this case all the coal mines in the country), can be used to measure the average risk. There are two chief factors in falls of ground risks : (1) The liability to a fall of roof or sides ; (2) The liability to coincidence, in time and place, of a person and a fall. Association of these two factors involves chance. A split second or a few feet may mean the difference between a fatality and no accident at all. Chance of an accident can be reduced by decreasing the number of falls where persons are engaged, but it can be decreased even more by reducing the number of falls where and when most man-hours are spent. Proper regard for the element of chance in the risk of falls accidents is most important, especially as some colliery managers are inclined to counter proposals designed to reduce falls liability, even at places where man-hours are high, by stating the apparently small number of falls accidents during the last year or two at the places concerned. In all probability, one fatality, for example, in 10 years at that particular place would be an abnormally high rate, If there are 10 roadheads in a colliery and the liability to a falls-accident at any roadhead is one in ten years, then this means one accident a year at road-heads at that colliery. Removal of support results from coal-cutting, working off coal, withdrawing supports previously set, and failure of supports due to fracture, instability or displacement. As a consequence, the roof beds lower in advance of, at, and behind the coal face, and under the increased pressure transmitted to the coal ahead of the face, the roof, coal and floor are all squeezed out laterally towards the worked out area. These movements follow the path of least resistance, a fundamental factor for consideration where excessive movements towards roads or other places cause serious damage. The faster the rate of removal of support, the quicker and more extensive are the strata movements induced. Sprags, props, chocks, and packs have to control the strata movements and also to provide immediate and adequate support to detached masses of roof or sides and so prevent them from falling. As these roof breaks are formed ahead of the coal face and inherent weaknesses also exist there, it is immediately the roof is exposed by cutting, working off coal or ripping in roads, that support by props and sprags is most needed. It is there also that the most man-hours are usually spent by machinemen, holeborers, shot-firers, and strippers and rippers. Thus the greatest risk of coincidence of falls and persons occurs there. In the process of erecting supports a certain amount of exposure of ground for the purpose of securing it may be unavoidable, but the smaller the area of ground exposed before setting supports the less is the danger. Certain kinds of supports, such as fore-poling and even spragging coal with long holing sprags, get over this difficulty. The first fundamental rule for reducing falls-accident risks is that adequate support must be given to the roof (and sides) as and when they are being newly exposed. No newly-exposed roof or sides are fit to be relied on without support. The minimum of time must be spent within range of falls from unsecured or insufficiently secured roof or sides in moving ground. Strata movements must be reduced to the minimum by adequate support with the minimum of delay. The Supports. It is important that each support set should perform its allotted function. To accomplish this, a few simple matters require continuous and consistent attention. Holing Sprags. — It is compulsory to set holing sprags at intervals not exceeding 6 feet. They are necessary not only to prevent cut coal from falling, but also to support the roof through the coal. To be most effective, holing sprags must be applied as near to the coal cutter as possible, having regard, of course, to danger from the cutter picks. When modern mechanical gummers are used, and their numbers are increasing, holing sprags are even more necessary to support both coal and roof. Props and Bars or Straps. — In use the load is applied to props by the converging movement of the roof and floor. It depends, not only on the strength of the props, but also on the areas of contact between the props and the roof and floor and on the crushing strength of any intervening lids or bars. To enable a prop to offer and maintain continuous resistance throughout its service, to prevent the prop from being overloaded, damaged, or displaced, provision for the height loss is essential. In every case where supports at a working face are being seriously damaged or broken, necessitating material and labour for renewals, it is necessary to see that sufficient provision has been made for the height loss. This provision can be made in various ways. Soft wood lids of thickness to suit the height loss can be used with the props. As wood is weaker to pressure applied at right angles to the grain than to pressure down the grain, the lids should yield and be compressed before the props are fully loaded. The lids should be larger in area than the end of the props set to them. Obviously there are limitations in the thickness of lids which can be used with props of different diameters and lengths, but in general the lid thickness should not exceed the diameter of the prop. If this is insufficient for the height loss, then additional steps must be taken to reduce the height loss, for example, by better packing, additional chocks, and earlier withdrawal of the props. With wooden props, if the end areas are reduced to less than half their original, the ends burr instead of penetrating. During burring, stability may be reduced. When wood or steel props with reduced ends are used they should be dented into the floor when being set. This is good practice whether the ends are reduced or not, but it is more important with reduced ends because the diagonal lengths of the props are then nearer to the axial lengths, and consequently they are easier to knock out. Straps. — Whether they are of wood or steel straps help to distribute the resistance of the props over a larger arei of roof than capped single props, and at the same time they increase the stability of the props subjected to lateral movements. Chocks. — The resistances and compression, under load, of chocks are determined largely by the areas of contact between the pieces and the kind of wood. Chocks built from ordinary round soft wood props, or any chocks built on thick layers of rubbish, are of little service at working faces. Packing. — Pack resistance and compression records taken in various collieries usually show a low resistance and large amount of compression in the early stages — as low as 10 lb. per square inch for the first 20 per cent. of height loss, apart from the initial loss of height without resistance when the pack is not tightened up to the roof. With further compression the resistance usually increases fairly rapidly unless the side walls burst out and allow the resistance to drop. Pack compression has been found to be less at the centre of the pack than at the sides. This is due to the better supporting power of the material at the centre, resulting from the reinforcement of the face walls of the pack, by each successive strip of packing added. The practice of burying the packs at road sides provides similar reinforcement io the side walls. It is evident that stability of side walls is a very important matter. To some extent intermediate cross walls ease the lateral pressure which tends to burst out the side walls. Perhaps the most important of the several items concerned in packing quality is the stability of the side walls, obtained by using small material for bedding the walling stones. Irregular shaped stones built in pack walls only touch one another over small areas, and under pressure the stones move and frequently fall out. By filling the spaces between the stones with small material, which acts like "mortar," this is prevented whether the walling stones are small or large, weak or strong. This is a very simple matter involving no extra labour, but it contributes appreciably to the stability of pack walls. Roof conditions at the face can usually be much improved by better quality packs, built closer to the face and, if possible, built sooner, but it is difficult to convince those who have become accustomed to bad roof conditions, which they may attribute to vagaries of nature, that the conditions can be improved by such relatively simple means. [To be continued]
|
|||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||