Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

21st March 1942, Page: 262, Column: 1

Correct Use Of Mine Timber — II

Extracts from paper on "Mining Timber: Possible Economies and Substitutes," submitted at the February general meeting of the North of England Institute of Mining and Mechanical Engineers.

By L. C. Maitland.

The correct use of timber is one of the most important points in roof control and, if properly carried out, can effect considerable economies. Even more important than this is the definite reduction in the accident rate. When the best system has been proved it should be adhered to rigidly; this can be done only by intense supervision, and supervision all the time. No detail is too small to be considered ; the greater the attention paid to detail, the greater will be the economies effected.

The following points from Pamphlet No. 3, issued by the North of England Safety in Mines Research Committee, give briefly the most important points to remember :—

"A wood prop 5 feet long will shorten only about 1/5 inch before it breaks. But wood is much weaker across the grain than along it, and a plank or cap set between the roof and a prop will crush under loads much less than the strength of the prop. A plank or cap 5 inches wide and 2½ inches thick set above a prop 4 inches in diameter will crush 1¼ inches under a load of 10 or 12 tons. This load is only half of that required to break such a prop. A good working rule is that the amount of controlled movement under comparatively small loads is equal to about half the thickness of the planks or caps used.

"Supports should be set as close to the face and as soon as possible, and so far as practicable so as not to require alteration afterwards.

"Systematic support implies that each support shall carry its proper share of the roof load.

"The practice of setting props directly against the roof without the use of a cap, and the use of caps of different thicknesses or incorrect setting of props through any cause, will generally result in unequal loading of the supports and will have a very definitely bad effect on roof conditions.

"Planks should make contact with the roof along their whole length, and where the roof is uneven any space between a plank and the roof should be filled with suitable packing pieces.

"The harmful effects which result from the unequal loading of supports, due often to lack of attention to detail in setting them, deserve the careful thought of every miner.

"Caps should be of equal thickness ; square-cut caps are best, are more easily set, and should be always used. When foot pieces are necessary, they should always consist of sufficiently thick square-cut timber and be properly seated on the floor.

"If too few supports are set, the load on each may be too great, and the supports, the floor, or the roof may be broken, but if the load be carried securely by a sufficient number of supports, lowering will be uniform and gradual and the roof will be less likely to break."

Emphasis might be laid on the points — supports should be set as soon as possible, also as tightly as possible — do not leave the roof to tighten the prop.

It is well to remember also that props of equal diameter may vary in strength as 1 is to 4 ; the unexpected failure of a prop will throw a greater load on the next props, cause them to fail and possibly cause a fall of roof. It follows that it is unadvisable to mix different sizes of props on the same face, or steel and wood supports.

Whenever possible, timber stocked underground should be located in a dry place. Dry props are 50 per cent. stronger than wet, and the weight is considerably less. A reasonable supply of roof supports should be kept in every working place, so that they can be set immediately they are required, thus preventing excessive and irregular roof movement.

Whatever the system of support, constant supervision and vigilance on the part of the officials and workmen will always be necessary.

Another very important point is the complete and prompt withdrawal of all timber from the wastes ; much timber is lost altogether, and much is damaged beyond further use because the withdrawal has been delayed too long.

The regular advance of the face, with a unifoim cycle of operations, is a considerable help in timber economy ; in some circumstances extra supports set to carry over week-end and holiday periods are a sound economy.

Where coal-cutting is done keep the packs as close to the face as possible, and do the packing, drawing of timber, etc., before cutting, so keeping the span of roof to be supported at the minimum. Also use steel holing sprags for putting in the cut immediately behind the machine ; these should be not more than 4 feet to 6 feet apart. These form a rigid support and prevent the sudden and excessive roof settlement which occurs as the machine moves across the face and often causes considerable damage to the roof supports. If a gummer is used on the coalcutter, the use of good holing sprags is even more important. In most cases, if not in all, a gummer is an advantage ; about 80 per cent. of the holings are brought out, and if by using steel holing sprags the undercut coal and roof are kept up, greater advantage is got from the shots, or other method of getting the coal down.

It is important that the face should be kept straight, in both longwall and bord-and-pillar broken workings ; a straight face ensures uniform roof loads, which can be systematically supported with the maximum economy. The line or angle of the face may play an important part in roof control and timber economy, the most suitable angle being found by experiment ; a change of angle may sometimes convert what was apparently a bad roof into a good one.

The correct use of face or strip packs often has a considerable effect on the control of the roof, and consequent economy of roof supports ; a row of props may be saved, and a number of the props may be fit for use again — which at any time is an important consideration, but even more so to-day, in view of the prospective timber shortage.

A row of chocks set on the waste side of the face, acting as a "breaking-off" line for the roof, is very successful in many conditions, and often saves a number of props. The row of chocks should be kept straight and the packs, if any, kept as close to the face as possible if the best results are to be obtained. It is usually advisable to use some form of chock release, which enables the chock to be built tightly between roof and floor, thus affording the maximum support facilitating systematic withdrawal, with greater ease and at a lower cost. The time saved by the use of this device is "in hand" in case of delay in some other part of the cycle of operations.

Other directions in which timber economies can be effected are stated briefly below :—

(a) Underground curves on haulage roads. As far as possible these should be constructed with concrete — considerable quantities of large-sized timber will be saved.

(b) Haulage wheel frames. In many instances these can be constructed of steel built into concrete or brickwork.

(c) Underground sleepers — steel sleepers are being used in some pits and are giving complete satisfaction.

(d) Roller frames — these can be of steel which would save a large quantity of timber.

(e) Coal tubs — large quantities of timber are used in the construction and maintenance of these, most of which would be saved if steel tubs were used.

(f) Many of the gangways on the surface could be constructed in concrete — which makes a permanent job and saves a lot of timber.

(g) Flooring in many of the surface buildings could be concrete.

Weekly records of timber used underground and expressed in terms of timber used per ton of output give a useful check on timber consumption.

Systematic salvage of all timber used underground, on the faces and roads ; and prompt salvage of districts, and faces which have finished, is important work and should be under the control and supervision of an official who is responsible for nothing else.

In some conditions useful economies in timber have been effected on longwall faces by the use of "pots" — short lengths of piping 6-inch to 8-inch diameter by 8-inch high — these are nearly filled with small dirt or holings on which the prop is set. The compression of the dirt accommodates the gradual settlement of the roof. This system requires careful supervision, because the "pots" must be set properly, if not, they are a further source of danger.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Maitland, Lionel Clinton      Whos Who Page



Related Articles

Pub.
Date
Article (Newspaper)
07 Mar 1942  Mining Timber (The Science and Art of Mining)
21 Mar 1942  Correct Use Of Mine Timber — II (The Science and Art of Mining)
04 Apr 1942  Steel As Timber Substitute (The Science and Art of Mining)

 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print