13th December 1941, Page: 180, Column: 1
Underground Belt Transportation
Extracts from paper prepared for presentation before the Coal Division of the
American Institute of Mining and Metallurgical Engineers and published in
Mining and Metallurgy, the official organ of the Institute.
By Carel Robinson.
A serious objection often raised to belt conveyors is that the belts are so
easily damaged that from time to time one must expect them to be destroyed.
This, however, is not a valid objection. Admittedly, a belt can easily be
damaged, but it need not be.
When precautions have been followed closely, experience in actual operation has
proved that extensible belt conveyors, correctly designed, will operate for
years without any damage to the belt other than normal wear. When a belt
conveyor is first installed a thoroughly competent man who is to have complete
charge of the equipment should be selected and carefully trained. Automatic
protective devices should be installed. These devices will stop a belt
automatically if a splice pulls in two, if the belt starts to slip, or if a
leading conveyor stops. In addition they automatically stop all other conveyors
behind the belt when it stops. Extreme care should be taken to arrange loading
points to ensure proper feed to the belt, and especially is it of vital
importance that all spill plates be correctly installed.
Mines with seams of coal 4 feet thick and more provide virtually an untapped
field of application for belt conveyors. In normal operation every item of
cost, either capital or operating, is reduced as the seam becomes thicker. The
dependability of belts assures almost complete freedom from haulage delays,
which is reflected directly, of course, in decreased cost, and indirectly in
the improvement in morale, for haulage delays are among the most demoralising
delays around a mine.
The rate of peak production for each conveyor unit should approximate the
capacity of the belt. The rate of delivery to the belt should be as uniform as
possible and as near the peak capacity as possible. To accomplish this, mining
plans and schedules should be adjusted so that approximately the same
production per shift is obtained as the entry advances as on retreat.
The indirect economies of belt conveyors are numerous but are hard to evaluate
in dollars and cents.
For general consideration, a brief list of advantages is presented. Any
operator considering the use of belt conveyors should check this list, or one
of his own composition. For any given mine, these factors can generally be
approximated satisfactorily. Naturally, certain conditions are encountered
where the entire list may mean little, in others, a great deal.
Advantages of Belt Conveyors.
Following are the most important advantages :—
(1) If properly planned, an average of less than five minutes' delay per shift
caused by the transportation system can be expected with belt conveyors. This
figure is based on actual performance over a period of years. This small delay
time looms large in importance when the delays of mine-car transportation are
considered ; wrecks, derailments, broken rails, power lines down, faulty
dispatching, and all the other countless causes.
(2) Belt conveyors are less hazardous than mine-car haulage.
(3) Belt haulageways can be timbered at less expense and more effectively.
There is no danger of knocking out timbers on belt lines, and accordingly many
places can be timbered safely that would be traps in the event of derailment
with mine cars.
(4) After the main features of transportation by belt conveyor have been worked
out, the problems incident to transportation virtually disappear. This is in
direct contrast to the ever-changing problems incident to mine-car haulage,
which occupy a large percentage of management's time. With belt conveyors the
management is able to concentrate more time and effort on face performance,
with resultant decreased cost.
(5) In rolling, faulty, or irregular seams; belts can be used efficiently where
mine car haulage would be expensive, or even prohibitive.
(6) Since belt conveyors are only 18 inches or less high, no change in haulage
equipment is required where seam conditions change radically.
(7) By simply changing the speed of a 30-inch belt conveyor (provided equipment
is so designed), tonnages ranging from 100 tons per hour to 400 tons per hour
can be efficiently hauled.
(8) Power cost is generally cheaper than with mine-car haulage, owing to steady
load with no peak demand. A.C. power can be readily used, further decreasing
power cost.
Disadvantages of Belt Conveyors.
Disadvantages of belt conveyors may be enumerated as follows :
(1) Frequently, belt conveyors have a higher initial capital cost. In a
surprising number of instances, however, this need not be true.
(2) The belting is essentially fragile. Constant and expert maintenance is an
absolute necessity. Proper safety controls must be installed and maintained.
Expert care must be taken to set up loading points properly. Unless these
points are given attention, costly damage to the belting can be expected.
(3) Where the mine floor is subsiding or where there is much movement of the
mine floor, belt lines may get out of alignment and either cause damage or
delay until the situation is corrected. Belts must run in straight lines, and
hence are difficult to use in development around faulty areas.
(4) Belts do not provide storage to permit continuing work at the face when
there is a delay at the tipple end. A storage supply bin is frequently
required.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Robinson, Carel | | | |