|
15th November 1941, Page: 150, Column: 1 Coal Dust ResearchMidland Colliery Owners' ReportsThe Mines Department having requested the Mining Association of Great Britain to investigate the problem of the reduction of coal dust in underground workings, the Midland Counties Colliery Owners' Association agreed to collaborate in the research work. A full-time underground Investigator (Mr. J. T. Barclay, B.Sc.) was appointed under the control of the Association's Coal Mines Act Committee of which Mr. G. Nicholson is chairman, the investigations being under the direct supervision of Professor P. L. Collinson of Nottingham University College and Mr. A. E. Naylor of the Shirebrook Colliery Co. Ltd. The essentially practical nature of the research work is clearly recognised, and detailed reports Will be published from time to time. Up to date over 2,600 samples of dust have been collected, sieved and analysed, and the Committee has issued the First Interim Report together with the First Report on the Problem of Coal Dust deposited beneath Underground Gate Belt Conveyors. Extracts from the interim report are appended. Conveyor Dust Problems. Extensive tests have shown that, where gate belt conveyors are employed, the greater part of the dust settling in the roads comes not from the actual loading point, but from the surface of the belt along its whole length, thrown off mainly at the bottom or return rollers. The largest quantity of dust reported as having been collected by any of the devices designed for dealing with dust at loading points has been about 300 lb. in a working shift, whereas from 800 lb. to 1,000 lb. has been collected in this time from the belt surfaces of comparatively short belt conveyors in dusty seams in the Midland coalfield. . . The dust problem at conveyor loading and transfer points may be a very serious one, as the dust is dispersed into the air-current and may affect the health and comfort of the men, and reduce visibility, apart from the explosion danger. A series of tests made with an electrically operated dust collector at a very dusty point in the Blackshale seam showed — by means of deposition tests employing metal collecting trays — that the apparatus effected a reduction of between 60 and 70 per cent. in the quantity of dust settling on the sides of the roadway within 80 yards of the loading point. This apparatus is very useful for pits where no compressed air is available. The essential features are that the dust laden air is drawn from the loading point (Which must be covered by hood or canopy) by a 5 h.p. Sirocco type fan through a vertical tube, in which it is given a swirling motion and then passed through a water spray. The dust settles on the sides of the tube in the form of slurry and drops into a chamber below. Tests have also been conducted on the alternative method of dealing with this problem by settling the dust clouds by water or mist sprays operated at the loading point without a suction fan. Experiments with ordinary sprays have not been very successful. The best result obtained showed a reduction in the dust deposited in the vicinity of a loading point of only 40 per cent. At one colliery considerable success in dealing with the whole problem of conveyor dust has been obtained by spraying the coal as it is discharged from the face conveyor on to the tension end of the gate conveyor. Tests have shown that by this means a large reduction is effected in the dust produced at all points, and tackling the problem at the earliest opportunity is certainly a step in the right direction. Great care has to be taken, however, to prevent the gate conveyor belt becoming wet, as if this occurs trouble may be caused by slipping on the driving drum, or the effective life of the belt may be reduced. The investigations have shown that excessive dust is sometimes produced on gate conveyors through the following causes : (1) Careless or incorrect erection of the conveyor-loading point resulting in an excessive drop from the top of the loading drum to the bottom of the tub ; (2) Excessive belt speed, which causes the coal to be delivered With too great a velocity and so often gives rise to spillage ; (3) Obstruction of the space through which the air passes into or from the coal face at the face end of the conveyor road, when this is also used for ventilation ; (4) Bad alignment of the conveyor, and faulty levelling. By attention to the above points a big improvement in the conditions of the mine in regard to coal dust can often be effected without the application of any special apparatus. Dust on Roads and Airways. A great amount of very fine dust produced on modern mechanised faces may pass into the return airways. This is especially the case where the "gummings" are filled out with the coal, and where pneumatic picks are employed. Much of this dust is very fine, and is carried long distances. Experiments were carried out by hanging greased brattice sheets in a return airway, placed in a staggered manner partly across the road, and it was found that by this means approximately 40 per cent. of the fine dust could be trapped. It is of importance to note that during these tests it was shown that 97 per cent. of the dust settling in the airway would pass through a 240-mesh sieve (B.S.S.). The sheets were hung at an angle of 45° to the sides of the road to afford as little resistance as possible to the air flow, and no appreciable difference in the quantity of air passing could be observed by anemometer readings. The quantity was large, however — 22,000 cubic feet per minute — and it might be necessary to place the sheets at a more acute angle if the quantity Was small. Three sheets were hung on each side of the roadway, in a staggered manner, and each sheet reached halfway across. For convenience the sheets were fixed on light wooden frames so that they could be swung out of the way when timber and other supplies Were taken up to the face. During the tests the sheets were coated with thick conductor oil, and after two or three shifts they became thickly covered with dust in the form of oily sludge. At the end of the week they had become "saturated" and the sludge was scraped off and the sheets re-oiled. The length of face was 375 yards in a seam 5 feet thick. The advantage of this device is that it is very simple, inexpensive, and requires little attention. The question of the type of oil to be used is important, as if an oil of low flash-point were employed there would be an obvious fire risk. The oil or grease should therefore be of a kind not easily ignited, and investigations are proceeding into the possibility of using some other substance of a sticky, but non-inflammable nature. Sheets soaked in calcium-chloride solution have been suggested. Bird lime is effective, but difficult to apply underground. It is important to note that the inert dust and coal dust on mine roadways should be mixed as intimately as possible in order to preclude the formation of a surface layer of coal dust which might propagate an explosion. In order to ensure the presence of an intimate mixture of the inert and combustible dusts at all times, it would be necessary to deposit the inert dust in suitable quantities at all times when coal dust is being deposited. The tub-operated stone duster introduced by the Staveley Coal and Iron Company, Limited, and now used also in mines owned by other companies, consists of an open-topped metal box fixed near the roof of the road. Inside the box is a flat plate which is connected by light chains and a system of levers to another lever set between the rails of either the empty or full tub side of the haulage road. As the tubs pass along the road this "track" lever is depressed by the tub axles and causes the plate to be raised. After each axle passes over the lever the plate quickly returns to its first position, by means of a counterbalance, and this causes a small quantity of stone dust to be ejected through the space between the sides of the box and the edges of the plate and also through holes in the plate. The dust is raised into the air, and this results in an intimate mixture of the coal dust and stone dust on the floor, roof and sides of the haulage road throughout the shift. The quantity of dust liberated can be regulated by altering the lengths of the levers. This apparatus Was tested on a main intake airway where the boxes were set at 200-yard intervals ; approximately 2,000 tubs passed per 24 hours, and ¾ cwt. of limestone dust was distributed from each box in that time. The results on the roadway were excellent, no other stone dust being necessary. The great advantage of this apparatus is that it can be used on any haulage road, except possibly where the haulage speed is high, and it is not dependent on any source of power. . . The device does not Work very well if the conditions are damp, as the stone dust then tends to clog in the box. The use of dust treated with stearic acid is advisable under such circumstances. Working Face Dust Problems. Tests have been carried out with mechanical "gummers" attached to coal-cutting machines. These often result in a great improvement in the conditions not only during the cutting shift but also during the filling shift. The direction of the line of face in relation to the cleavage has been found to have a big effect on the amount of coal dust produced. Faces on "end" in general make much less dust than faces on any other point. Where a face is being worked at an angle of 45° or thereabouts to the cleavage, it has been found that more dust is produced when cutting with the cleats than when cutting against them. This held good not only whilst cutting was in progress, but also on the following filling shift, and was noticeable even at the gate conveyor loading point. It has also been shown that more dust is produced during the first working shift following a holiday period than during subsequent shifts. Dust Problems on Surface Plant. Considerable success has been obtained by the use of steam at the tops or mouths of bunkers such as those used at coke ovens. Steam can generally be obtained cheaply from the boilers at such places, and if a series of jets is directed downwards into the mouths of the bunkers at the points where the coal is delivered from the elevator or delivery conveyor and light coverings placed over the top, practically all dust can be eliminated. At one surface plant tests showed an improvement of up to 90 per cent. Only a small quantity of steam at a low pressure — 20 lb. per square inch is ample — is required to obtain this result, and a simple but effective form of jet can be made by flattening the end of 1-inch diameter pipe to a fishtail form With an opening 1/3 inch to 1/16 inch wide. Such jets can also be used effectively at surface conveyor transfer points. The use of steam jets on tipplers is also recommended. The jets should deliver downwards on the side on which the tub turns over, but the quantity of steam must not be large, otherwise it may blow upwards and interfere with visibility. For efficient working the sides and top of the tippler should be covered. The problem presented at dry cleaning plants has not yet beon fully solved, but if the plant is compact very efficient results can be obtained by covering the cleaning tables and drawing the dust laden air away by fans to cyclone separators. Where the plant is large and scattered this would involve great lengths of piping. In all cases effective screening before cleaning is of great importance. The quantity of dust produced at these plants may be very great; at one plant it was found that the deposition on the floor of the building was at the rate of 11.8 grams of dust per square foot per hour. Two men were employed continually in collecting and removing the dust.
|
|||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||