18th October 1941, Page: 123, Column: 2
Inspecting Engineer's Duties
At the July meeting of the South African Institution of Engineers
Mr. R. H. Harriss in his presidential address dealt with the methods of inspection
and testing of metals before and after fabrication. The subject of his address
was "The Inspecting Engineer and Engineering Inspection." Some
extracts are appended.
In inspection, the gauging system is very important and tolerance, limits and
clearance are the chief features.
"Tolerance" can be defined as the permissible variation in a given
dimension of a part in order to overcome unavoidable imperfections of
workmanship.
"Limits" are the maximum and minimum dimensions of a section
prescribed to allow for variations in both fit and workmanship.
"Clearance" is the difference in dimensions between the two component
parts which are assembled together.
The Inspecting Engineer must know his job thoroughly, and should have a
thorough knowledge and understanding of human nature, in so far as engineering
is concerned.
The first essential is probity ; in this respect he must be like Caesar's wife.
He must be able to get things done without unnecessary friction, and always
have a friendly feeling towards the personnel in a works and yet must
studiously avoid accepting any hospitality.
He must have a sound knowledge of mechanical engineering and the testing of
metals for tensile, compression, impact and bending properties. He is also
expected to have a fair knowledge of chemistry and physics; the methods of
manufacture and production of metals as well as their thermal and mechanical
treatment ; to know the difference between Bessemer and open hearth steels and
acid and basic steels, and the effects of the various elements and alloys on
both ferrous and non-ferrous metals, and not to make the mistake of thinking
that a manganese bronze necessarily contains manganese.
The Inspecting Engineer may be called upon to discuss pyrometers and
macrostructure of metals and to look moderately interested when shown a sulphur
print, and all this in the interval of carrying out tensile, bending,
alternating stress, hardness and other tests.
It is obvious that he cannot know everything, but being a wise man he looks
around to find those who can help him in matters where his own knowledge is
deficient, and then with due prudence and tact he gets over the difficulty.
In the testing of engines on the test bed, there are factors which the
Inspecting Engineer must bear in mind in addition to, say, freedom from knock
and cool running. He must realise the possibility of unforeseen dangers. For
many years it has been known that creeping cracks in shafts may be started as
the result of a scratched surface, and they may occur in a shaft with a
mirror-like finish if very heavy roughing cuts have been made prior to
finishing and polishing or grinding. How often have we seen heavy shafts
fracture from a small crack starting in a too sharp radius, and the Inspecting
Engineer must be able to judge whether a radius is correct or otherwise.
In hardness testing, the greatest care is necessary in selecting the best
position on the material so as not to interfere with the stress load capacity.
The experienced Inspector can gauge fairly accurately the tensile properties of
the material by the Brinell test.
In taking tensile tests, I always made it a rule to use the dividers by placing
the points in the pop marks and chalking the surface of the test piece, then by
keeping one leg in the lower pop mark and scratching a line across the top pop
mark surface one can instantly see when the yield takes place by the thickening
of the scratch line ; and one can practically tell by the yield point what the
ultimate stress and elongation will be, but this can only be acquired after
considerable experience.
As is well known, practically all engineering practice is supposed to be
carried out to the specifications and standards laid down by the British
Standards Institution. The Inspecting Engineer's duty is to see that
manufacture and fabrication are carried out in accordance therewith, but there
is always a gap somewhere between the actual production and the Standards, and
the Inspecting Engineer has to be wide awake. All British firms of repute work
to such standards whether the purchaser's specification calls for it or not,
but there are others who are not so particular.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Harriss, R. H. | | Mining Engineer | |