4th October 1941, Page: 100, Column: 1
Governed Braking System
The chief engineer of the Zinc Corporation, Ltd., of Broken Hill,
Mr. Theo. M. Carey, has submitted a paper for the consideration of members of the
Institution of Engineers of Australia in which he describes the plant recently
installed at the mine operated by the owners. The present depth of the mine is
2,251 feet. Shaft sinking is in progress and it is expected that ultimately
considerably greater depths will be mined. The title of the paper, which is
reproduced in the Transactions of the Institution, is "Electric Winders in
Metalliferous Mines," and under the sub-head Governed Braking Systems
Mr. Carey says :—
The brake engine in the Metropolitan-Vickers governed braking system is oil
operated and is raised by oil pressure to release the brakes. When oil pressure
is released the brakes are applied by the falling brake weights. The oil supply
is obtained from an accumulator and pumps and is regulated, to the brake
engine, by the main control valve. In the valve are a sleeve and a plunger, the
relative position of which connects the brake engine to pressure or to drain.
The sleeve is operated through a floating lever, from the driver's hand lever
and the solenoid weight. In normal winding the solenoid holds up the solenoid
Weight, and the driver's hand lever can then move the sleeve over nearly its
full possible range of movement, raising the sleeve to put the brakes on. When
the solenoid is tripped for emergency braking the weight falls and raises the
sleeve to its maximum height, irrespective of the position of the hand lever.
The plunger is raised against a spring by a follow up from the brake engine
position, so that over a certain range of operation there is correspondence
between the hand lever position and the position of the brake engine. The
plunger is also capable of being further raised by oil pressure from the
governor, which may be admitted to the bottom chamber of the main control
valve. When the plunger is so raised the fulcrum rises in the slot, and the
governor takes over control of the plunger movement from the follow up. The
plunger rises to take the brakes off. The follow up alone cannot raise it
sufficiently to correspond to the highest position of the sleeve, but the
governor can raise it beyond this position.
The governor is driven from the Winder drum through shafting and bevel wheels.
The governor shaft is vertical and carries a driving member from which the
governor flywheel is supported by swinging links. When the winder is
decelerated the governor flywheel tends to run forwards and, therefore, swings
upwards on the links. The swinging raises a plunger in the governor which, if
it rises sufficiently, relative to the sleeve in the governor relay valve,
admits pressure oil to raise the plunger of the main control valve. The
swinging of the governor flywheel is damped by a dashpot arranged between the
driving member and the flywheel. The compensating sleeve in the relay valve is
operated by lever gear from the main control valve plunger.
So long as the winder is running steadily, or with a low deceleration, tho
governor relay valve is connected to drain and the governor does not influence
the main control valve, so that the braking is regulated solely by the driver's
hand lever. If, however, an excessive deceleration is built up, due to violent
braking, the governor flywheel rises sufficiently to connect the relay valve to
pressure and the main control valve plunger is thereby raised. The brake engine
is thus connected to drain and the brakes are relieved. The compensating action
ensures that the braking is so regulated as to give a deceleration which
depends only on the position of the control valve sleeve. As soon as the winder
has come to rest the cessation of the deceleration causes the governor flywheel
to fall, and the brakes are thereby applied with full force. The governor is
responsive to total deceleration from all sources, including, for instance,
regenerative braking in the Ward-Leonard electric winder, and regulates the
mechanical braking, so that the total deceleration is a fixed figure.
A secondary trip gear is included with the brake governor equipment to give
duplicate protection against any possible failure of the brakes to be applied
after an emergency trip. The emergency valve in the secondary trip gear
functions only if, after a certain time interval from the emergency trip, the
brakes are not full on. This time interval is varied with the position of the
skip in the shaft so as to be sufficiently long to allow for governed
deceleration from full speed in mid-wind, but is shortened when approaching the
bank so as to give adequate protection against possibility of overwind. When
the emergency valve falls the brake engine is cut off from the main control
valve, and is connected to drain through an orifice which prevents too rapid
fall of the brakes. An interlocking arrangement has been provided so that, if
the emergency valve has once tripped, it cannot he reset unless the main
control valve outlet is at low or drain pressure ; that is, unless the brakes
will remain hard on immediately after the resetting of the emergency valve.
Smooth and stable operation of the brake governor gear is ensured by the
insertion, in certain pipes, of orifices of sizes determined by experience, by
the provision of special porting on the main control valve, by damping of the
appropriate intensity in the governor and by a choice of lever ratios and valve
strokes determined by experience. The whole system has been designed to give
the greatest possible protection against excessive stresses on winding ropes,
consistent with brake control for manoeuvring, and, when used in conjunction
with a suitable overspeed trip, with complete protection against overwind.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Carey, Theo. M. | | Chief Engineer | |