31st May 1941, Page: 371, Column: 1
Waste Of Lubricating Oils
At the February meeting of the South African Institution of Engineers
Mr. Wilfred Gooday, A.R.S.M., D.I.C., read a paper on "Conservation of
Lubrication and Insulating Oils," in which he considered the scope for
reducing waste of lubricating and allied oils. He admitted that as compared
with the money spent on power and on upkeep, the cost of lubrication may be
small, but because lubrication influences power consumption and is a factor in
the life and the smooth running of machinery, it is important that the
comparatively small sum devoted to lubricants should be wisely directed. It is
futile to dictate over an office desk a detailed procedure for the lubrication
of a mine or works. Suggestions may be made and recommendations can be offered,
but their usefulness and accuracy can be assessed only in the actual practice
of lubrication on any particular plant. In the view of Mr. Gooday the
buyer is better advised to delegate the responsibility for selection to his
technically equipped supplier.
Storage.
Concerning storage of lubricating oils and greases and of transformer and
switch oils the Author emphasised the factor of cleanliness. If storage out of
doors is unavoidable, it is good practice to cover the containers to protect
them from the effects of weather, hot or wet.
Under cover or otherwise, care should be taken to avoid the ingress of moisture
or of abrasive particles of dirt or dust, which may easily render' useless all
the care that is taken to keep oils dry and clean and, in the case of
insulating oils, may reduce the dielectric strength below acceptable limits.
Drums should be stored preferably in a horizontal position and not on end, and
simple home-made stillage racks add to convenience in handling.
It is particularly desirable when drawing off the contents of oil containers to
remove any dirt from the bung-hole or neck so as to avoid possible causes of
contamination.
All the care given to the selection of lubricants, Mr. Gooday affirmed,
will be worthless if oils and greases become contaminated, for then, instead of
acting as unguents, they may become mere vehicles of abrasive matter or the
distributors of mischievous deposits.
Application.
Discussing the question of application the view was expressed that the various
means of applying lubricants, from hand-oiling to the circulatory system of a
steam turbine, can all operate under optimum conditions of waste reduction.
Bottle or needle oiler's, wick-feed or siphon oilers, ring and collar oilers
and mechanically-driven forced-feed lubricators, have all been designed with
the dual purpose of delivering oil automatically at a predetermined or an
adjustable rate of feed.
It is true to say that if the care usually bestowed upon, the lubrication of
air compressors, where over-feeding is positively hazardous, could be extended
to the oiling of many other units of plant and machinery, the resultant economy
in the consumption of lubricants would be tremendous, and the extremes of
prodigality and parsimony would both be avoided.
Where circulatory systems are installed, it is usual to find some means of oil
conditioning incorporated in the system, the effect of which is considerably to
prolong the life of the lubricant. The factors affecting the period of an oil's
usefulness should be remembered, namely, air, temperature, turbulence, water
and impurities. Anything that can be done practicably to minimise their effects
will extend the utility of the oil and so afford economies in what may be
hundreds of gallons of oil.
As an example of misapplication Mr. Gooday mentioned that rock drill
lubricants have been diverted on the Rand as emollients or cosmetics to the
anointing of native flesh. But that he said must have happened in the good old
times in which the Psalmist sang :—
"Wine that maketh glad the head of man
And oil to make his face to
shine."
References were made to the methods of reconditioning used oils, and Mr.
Gooday averred that a number of factors must be taken into account before
the best method of dealing with used oils can be decided upon. If a compromise
has to be arrived at it is desirable that it should be an intelligent one. On
the whole, allowing for very few exceptions, reconditioning of used oils is
best practised within the user's organisation where this is convenient for,
apart from the technical aspect, interest and skill in waste elimination are
likely thus to be intensified. Indiscriminate collection of all kinds of
products of centralised treatment may be useful, but it does not lead to any
better understanding by the user of the properties and values of oils, and can
easily evoke doubt as to the suitability for service of the hybrid products so
reclaimed.
Chemical Processing.
In the discussion following the presentation of the paper Mr. C. L. de Beer
confined his consideration to internal combustion engines in examining
the sphere covered by lubricating oils, asserting that there is only one method
really efficient, and that is the chemical, and even here great discretion is
required in discriminating between the several methods available. Chemical
processing would incorporate physical purifiers and, briefly, a chemical plant
could include the following :—
(a) Coarse filtering. It is surprising what solid impurities find their way
into the oil when it is being collected prior to renovating.
(b) Gravity separation of sludge, the majority of water and larger solids.
(c) Chemical treatment, such as by sulphuric acid or silicate of soda for
coagulation of grease or transmission compound with gravity separation.
(d) Heating to drive off the lighter fractions of oil, which are due to
dilution by the fuel and the cracking of the new oil under the very severe
conditions existing in the cylinders of internal combustion engines. These
fractions should be condensed and reclaimed, as they have a definite value
either as thin penetrating oil or as fuel.
(e) Chemical treatment by means of an alkali to neutralise excessive acidity.
(f) Chemical treatment by means, of activated earth to extract from the oil the
various impurities formed during use, such as carbon.
(g) Filtration to remove the chemicals added together with all impurities
absorbed or coagulated by these chemicals.
In the majority of cases all the above sections are not necessary, and the
general tendency is for the individual to exercise the utmost care in
collecting used oils to avoid contamination by grease and transmission
compound, so cutting out the treatment under (c) and the combining of sections
(d), (e) and (f) by using an activated earth with an alkali base and heating at
the same time.
The treatments (a) and (b) should form an integral portion of the used oil
storage tanks, and the whole chemical process is reduced to an extremely simple
and inexpensive treatment.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Beer, C. L. de | | | |
| Gooday, Wilfred | | | |