Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

8th February 1941, Page: 243, Column: 2

Coal-Cutter Bits

In his paper before the American Institute of Mining Engineers on "Mining — Machine Bits, Experience and Practice" Mr. A. Lee Barrett said they may be divided into three general classes, based on shape and method of use : (1) chisel, (2) pick-point and (3) one-use.

The "chisel" bits were made of steel of various sizes and were sharpened to a wide chisel cutting edge. Few of this type of bit are used, except in places where coring is very bad. Sometimes chisel bits are used with standard bits to help cut out the core.

The "pick-point" bit is widely used and normally it is made from ½- by 1-inch steel, is about 4½ inches long when new, has a rake angle of about 25 degrees, a front clearance of about 23 degrees, and a side clearance of about 8 degrees. There are many variations in the shape of this bit, depending on the ideas of the individual that may be dressing the dies of the bit machine. The bit usually is made from 0.85 carbon steel, although in recent years some alloy-steel bits have made their appearance. At present, carbon-steel bits are frequently tipped with hard facing materials.

The third class or type is called by Mr. Barrett the "one-use" bit; that is, a small bit that is used once and then thrown away. These bits have two or three points, are usually made from 0.85 carbon steel and sometimes from higher alloys. Recently some of them have been tipped with hard facing material. Many of them were used at first with special chains, but in recent years several bits of this class have been made for use in standard cutting-machine chains with adapters.

As the author explained, in good cutting practice each bit should break the coal between its point and the channel cut by the preceding bit, ensuring a minimum of actual cutting. The minimum number of bit positions compatible with the characteristics of the coal being cut should be used. This depends usually on coring ; only a sufficient number of positions should be used to cut a clean kerf. The number of positions ranges between five and ten with nine- and ten-position chains, in prevalent use at the present time. In coal of certain characteristics the number of positions in use might be reduced if enough attention were given to the problem.

Based on general experience Mr. Barrett says the following conclusions may be drawn:

The best bit is one that breaks the coal and does not cut it.

If bits are changed when they begin to get dull, maintenance cost and power cost should be the same for any good bit. These factors are not noticeably affected by the number of square feet cut by the bit.

The only satisfactory basis for comparing bits is by kilowatt-hours per square foot of undercut. Owing to the wide variation in cutting characteristics and in the handling of cutting machines, many tests must be run before an average can be reached that will be representative.

The introduction of an improved hammer-type bit-sharpening machine and a high-grade alloy steel, which is air-hardening, indicates that a bit of this type may well lead the field wherever a large number of bits are involved.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Barrett, A. Lee      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print