25th January 1941, Page: 229, Column: 1
Occurrence Of Creep
Recommendations of Commission
The following definition of the term Creep is given in a dictionary to which
reference has been made : The rising up of the thill in excavations in a seam
of coal, occasioned by the pillars not being left sufficient or not having a
sufficiently large surface to prevent their being forced into the thill by the
superincumbent pressure.
The ordinary mining man would explain that creep results from four distinct
causes : (1) Making the coal pillars under a soft roof or on a soft floor too
small ; (2) Extracting the pillars without system, and localising instead of
distributing the roof pressure ; (3) Robbing the pillars in a lower seam long
after they have been extracted in an upper one ; (4) Working narrow strips of
coal and leaving pillars between the gobs of two adjacent mines.
A somewhat serious occurrence of creep was the cause of trouble at the
Proprietary Coal Mine, Collie, centre of the coal mining industry of Western
Australia. A Royal Commission was appointed, to inquire into the problem, and
according to their report to the Government of the State the cause of the creep
appears to have been the unequal distribution of pressure on certain pillars in
an area where both floor and roof, particularly the floor, were weak. Other
contributing factors suggested by the evidence were that the pillars were high
and "on end" in relation to the cleavage, and the fact that the
affected area was in line with a fault, which appeared to have had a weakening
effect on the strata.
The Commissioners have made a series of recommendations, including—
(1) Future operations on the Collie mines should be conducted on a panel
system, whereby each section of the workings is totally surrounded by a barrier
of coal, the size of panels and width of the barrier to be approved by the
Minister of Mines with sufficient openings to allow for the proper working and
ventilation of the mine.
(2) Where possible, all bords should be worked at right angles to the direction
of the cleavage or cleat. Where this is not possible, they should be worked on
the cross. If necessary through a combination of circumstances to work on the
end, larger pillars should be left.
(3) Where fretting of pillars is observed, such pillars should be strengthened
by means of sprags, and in any area where excessive fretting is taking place
consideration should be given to the provision of larger pillars in subsequent
workings in that area.
(4) Large pillars to be left along all tunnels, slants and main haulageways.
(5) All main travelling roads to be clearly marked and strongly timbered,
preferably with chocks.
(6) No bords should be worked to a greater height than 9 feet, except by
special permission of the inspector of mines.
(7) Bords should be narrowed in known weak areas and when approaching faults.
(8) Faults should only be approached in every alternate bord and, where the
position of the fault is known beforehand, no cut-through should be constructed
which will leave a pillar of less than normal size against the fault. No
stripping of faults should be permitted.
(9) Care should be taken that the width of bords does not exceed 8 yards,
especially at the ends, where it should be preferably reduced.
It may be admissible here to recall a paper read some years ago before the
South Wales Institute of Engineers on "The Application of Cementation to
Mining." The author was Mr. H. Standish Ball, and he instanced a
case of the prevention of creep at a shaft bottom in a colliery where, owing to
the presence of water, the surrounding shale had been caused to swell,
affecting in turn the roof of the arched shaft siding, which showed signs of
serious collapse for a considerable distance. Mr. Ball said that in
spite of the concrete lining being one yard thick and supported by girders, the
strain was so great that a shield of wooden lagging had to be constructed as a
safeguard against the pieces of concrete which were continually flying off. As
it was difficult to tell at the commencement of the work where the water
actually was, three holes were bored vertically upwards for 120 feet at a
distance of 20 yards from one another without, however, tapping any water.
Holes were next bored vertically down, water being met with at a distance of 12
feet. Three series of holes were then bored : Series 1 straight down, series 2
at a dip of 45 degrees, and series 3 horizontally, each hole being
approximately three feet from its neighbour. The holes of series 1 were treated
first, followed by series 2, and finally by series 3. The whole of the affected
area was treated in this manner, some 600 tons of cement being injected at a
maximum pressure of 300 lb. per square inch. At the conclusion of the injection
the key of the arch was replaced by a fresh one, further cement being injected
through holes in the roof to render it as tight as possible. The work occupied
about two months, the whole siding was consolidated, and Mr. Ball
reported that no further treatment or repair work had been necessary.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Ball, H. Standish | | | |