|
30th November 1940, Page: 164, Column: 1 Sand And Clay StemmingBy H. Stafford, M.Sc, Ph.D., and. Prof. F. Stuart Atkinson, M.Eng. Extracts from paper on "The Preparation of Sand and Clay Stemming at Collieries" read before November meeting the Midland Institute of Mining Engineers. The importance of good stemming materials was emphasised by Ritson and Stafford as a result of work done at the University of Leeds prior to 1932. After taking into account the special difficulties and restrictions applied to Shot-firing underground, it Was recommended that a mixture of 3 parts of sand with 1 of clay should be used. This had proved to be the most efficient material for use under practical conditions. Since that time, however, much work has been done on the subject and much practical experience has been gained. It is now established that sand or hard grit is the most efficient stemming material available, and the only point of difference between the various workers concerns the most convenient means whereby sand can be effectively packed into the shot-holes. In considering the adoption of any particular stemming, due regard must be paid to the materials available, the ease of tamping the shots, the cost of material, and its transport and storage underground. The need for good stemming cannot be over-emphasised. Good stemming will prevent blown-out shots and will enable the explosive to do the greatest possible amount of work on the rock. It is of particular importance at the present time to obtain the maximum efficiency from all explosives consumed in mines. The use of clay as a binding material to enable sand to be formed into cartridges by pressure of the hands has much to recommend it. This is still the most popular kind of sand stemming used. Materials Required. The sand should be reasonably coarse and free from dust particles. The best size for the purpose will depend to a great extent on its subsequent treatment ; for example, mixing in mortar mills sometimes reduces the size of sand particles considerably. In general, the percentage of particles below 50 mesh should not exceed 20 per cent. nor should the percentage of particles over 5 mesh exceed 15 per cent. Substances such as brick dust or ground clinker can replace sand, and these are suitable provided that the size is as above and that they are hard enough to withstand grinding during the mixing operation. So far as the clay is concerned, it is often necessary to use such clay as is available locally. The best clay for the purpose is the sticky surface variety free from soil. The method adopted for testing clay as a binder for stemming is to dry it and grind it to pass 50 mesh. It is then mixed with coarse sand in various proportions and between 7 and 10 per cent. moisture is added. Cartridges are made from the mixtures by the pressure of the hands, and the clay is considered good if a cartridge made from a mixture of 3 parts sand and 1 part clay can be dropped from a height of 4 feet on to a hard floor without breaking into small pieces. Whatever binder is used, the cartridges of stemming must hold together. It is far more important to have a cartridge that will hold together while being pushed to the back of a shot-hole than to have the maximum amount of sand in the mixture. Calcium chloride is used for keeping the stemming material moist. The commercial flaked variety is suitable, and the amount necessary will vary with circumstances, such as whether the mine is hot and dry or damp, and whether the stemming material is to be used almost immediately or stored for weeks. It has not been found necessary to add more than 5 per cent. by weight in any circumstances and often half this quantity is sufficient. When the mine is wet, calcium chloride may not be required. Quite a lot of the sand and clay stemming is spoilt by the addition of too much water. The best sand and clay stemming is that which can be formed into strong cartridges with the lowest moisture content. Good stemming material may contain from 7 to 10 per cent. of moisture. Above this percentage the efficiency of the stemming material falls. For good stemming probably, the best proportion consists of 3 parts of sand and 1 part of clay. Tests have shown that such a mixture is not inferior to sand used alone. The proportion best suited to any particular colliery, however, will be governed by the quality of the binding clay available, and it must be remembered that it is of first importance to have strong cartridges for ease of tamping. Stemming made from 5 parts of sand and 2 parts of clay is almost as efficient as a 3 to 1 mixture. Mixing Machines. The machines used may be classified into three types : (1) Concrete mixer type; (2) mortar mill type; and (3) the bread-making or cordite mixer type. All three types are in constant use and each has its advantages and disadvantages. The Concrete Mixer Type has a revolving barrel with blades or other projections on the inside. The chief advantage of this type is that it does not grind the sand. Its limitation is that the binder clay used must be in powdered form. At those mines where facilities are available for drying and then grinding the clay, or where powdered clay is obtainable from local brickworks, or where the colliery stone dust is a suitable binding material, this is the best type of machine to employ. The Mortar Mill Type may be subdivided into two classes : (a) Machines with revolving pans and stationary rollers bearing on the pan ; (b) machines with stationary pans and revolving rollers. In this type, the rollers are capable of adjustment and can be made to run clear of the bed of the pan. The former is widely used because it often happened that such a machine was already installed when the question of mixing stemming first arose. Its limitation as a stemming mixer is that unless great care is taken by a skilled operator the sand in the mixture is rapidly ground. Often, when this machine has been allowed to run too long, the stemming material has been little better than clay. The second class (a) has its advantages over the revolving pan type. The stationary pans are fitted with a sliding door in the floor, and as soon as mixing is completed the material can at once be discharged. The rollers are capable of adjustment and can be lifted so as not to bear directly on the pan. In the Bread-making Type of machine twin paddles meshing into each other revolve in opposite directions, one at half the speed of the other. The containing tank is shaped to give only small clearance between the paddles and the sides. Machines of this type are used extensively for kneading dough and for mixing cordite and other similar materials. In operation, the machine appears to stretch the outside layer of the mass and push it into the middle. The great advantage of this machine over all others is that clay, as quarried and with no previous treatment, can be intimately mixed with the sand, and there is no appreciable reduction in the size of the sand particles. The disadvantages are the relatively high first cost and the cost of replacing the parts, which wear quickly owing to the abrasive action of the sand.
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||