16th November 1940, Page: 151, Column: 1
Gravity Coal Washing
At the September meeting of the Midland branch of the National Association of
Colliery Managers (announced in the Iron and Coal Trades Review), Mr. A. D. Cummings,
B.Sc, of. the Nottingham University College Department of Mining
and Fuels, gave a paper on "Gravity Coal Washing," in which he
reviewed the principal processes and considered the advantages that gravity
separation has over the older processes to offset the need to conserve the
washing medium. Some of his points may be summarised :—
The chief advantage of the new process is its ability to produce better yields
of cleaner coal than the older processes. Gravity separation has been
introduced to meet the need to wash poor coals to lower ash figures than the
older processes could hope to achieve, even by large sacrifices in the shale.
In gravity separation an accurate division into coal and shale is made at a
predetermined cut point. There are practically no wrongly classified products,
the clean coal and clean shale are nearly 100 per cent. correct.
Another important feature of the process is the ability to treat a wide range
of sizes in one plant, indeed in the same bath. This means economy of units,
and opens up the possibility of treating the whole mine output mechanically.
All the gravity processes can handle changes in the feed with great ease. The
results are equally as good when the load is up to capacity as when a few tons
per hour are passing, because, unlike a jig, there is no bed to be maintained.
This is also true for sudden changes in the amount of dirt in the feed. If an
unusually bad patch of raw coal comes suddenly there is no reflection of this
in the clean coal. The heavy overload of shale all sinks rapidly out of contact
with the coal and is disposed of as usual, and no adjustment of the plant is
necessary to deal with it. The handling throughout is very gentle, there is no
rubbing of piece against piece and consequently the amount of breaking down is
very small. Very soft coals can be washed with much less breakage than in jigs
and troughs.
Among the disadvantages cited by Mr. Cummings are the cost of reagent
and its recovery, whilst, since gravity separation is so far unable to deal
with coal below ¼ inch, it is usually necessary to provide additional
plant for ¼ inch to 0 coal. This counts as an extra in comparing with jig
and trough plants.
The author having stated that processes have been developed using (a) a true
heavy liquid, (b) solutions of soluble salts, and (c) suspensions of insoluble
material in water, considered the Chance process, the Tromp process, the Loess
process and the Barvoys process. Of the latter eight plants are working in
England. The inventor of this process has aimed at finding a suspension which
approximates as nearly as possible to a true liquid. The material used is
extremely finely ground barytes, all below 300 mesh and probably about 1/1000
inch, mixed with clay, which is smaller still. This mixture has the useful
property of being nearly stable at working strength, about 1.3 to 1.5 sp. gr.,
and of settling out fairly quickly barytes and clay together as a whole, when
diluted with water. This means that the bath liquid requires no currents or
agitation to maintain the suspension while the rinsing water is easily
concentrated. Owing to the smaller size, however, this concentration is slower
than in the other processes considered, and large thickeners are required.
The bath is similar to the other processes, all of them following the original
Lessing design. There is a constant supply of medium to the bath and an
overflow from it. This causes very slow currents, one upward and one downward
from the point where the medium is introduced in the middle of the bath, and
these serve to increase the speed of movement of particles near the bath
gravity. If lighter they are urged towards the surface, and if heavier towards
the bottom. This avoids the possibility of accumulated middlings interfering
with the separation. The separation can be a two-product one or, by introducing
an upward current at a suitable point on the shale exit, middlings can be
extracted. Both the Loess and the Barvoys remove middlings by upward currents,
and this product is not quite so accurately separated as in the Tromp process,
but as it has not a high value this is not a material consideration.
The Barvoys process possesses the advantage that, owing to the stability of the
medium, conditions in the bath are quieter than in any of the other processes.
For this reason, the separation of clean coal is very accurate. This is a point
of some importance for low-gravity cuts, for which purpose the Barvoys process
is well adapted.
This carries with it the disadvantage that the suspension material, being fine,
does not on settling separate out below the fine coal as in the processes using
coarser material. The whole of the solids, coal, clay and barytes, settle out
as one, and another means has to be adopted to get rid of fine coal in the
medium. This is necessary because coal increases- the viscosity of the medium
and interferes with the separation. The means adopted are screening on a wire
mesh and froth flotation of a portion of the medium in circulation.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Cummings, A. D. | | Nottingham University | |