2nd November 1940, Page: 129, Column: 1
Methods Of Mining In Pennsylvania
Extract from Technical Paper 590 [Analysis of Pennsylvania Bitumous Coal] of
the United States Bureau of Mines.
By Albert L. Toenges and Robert L. Anderson.
Pennsylvania ranks second in the United States in the production of bituminous
coal. This output comes from a large number of countries, where in many
instances physical conditions differ. Mining operations have been made to
conform to these varied local conditions, and space will not permit a
description of all methods and systems used in such a large field.
Underground Methods.
The mines using underground mining methods are developed by shafts, slopes, and
drifts. The system of mining is usually room-and-pillar or a modification
thereof.
In a typical plan with rooms and pillars the main entries are usually driven in
sets of four to eight parallel headings, which may either start from the main
shaft or slope and be driven towards the boundaries of the property ; in a
drift mine there may be a number of main openings from the outcrop into the
area to be mined. Other entries usually are turned at right angles off these
main headings at predetermined intervals. Barrier pillars, ordinarily 200 feet
wide, are left to protect these entries. Boom entries, which are in pairs on
approximately 50-foot centres, are turned off at right angles. The distance
between pairs of room entries depends upon the length of the rooms and whether
rooms are turned off both entries. Room lengths range from 250 to 300 feet, and
if rooms are turned off both entries the distance between two sets of entries
would be 500 to 600 feet. If rooms are turned from only one entry and driven
through to the next pair, the distance would be the length of the room, say 250
to 300 feet.
The centre-to-centre distance between rooms ranges from 30 to 100 feet,
depending upon the system of mining employed. Room widths are 12 to 40 feet,
and the pillar between rooms then depends upon the room width and centres.
Coal is extracted before advancing and retreating. Systems of development and
extraction vary according to the conditions met at each individual mine.
Concentrated Block System.
Some of the newer mines employ a concentrated block system of mining. The area
is developed by a main entry system consisting of a number of headings, the
number depending upon the size of the property and ranging from 3 to 7. In one
mine there are 14 main headings. When this number is used, they are usually
arranged in two groups of seven headings each, with a barrier pillar between
the groups. In each group two headings are used for haulage and one for a
manway, these three being the intake airways in the ventilating system, and the
remaining four headings are the return airways. Headings are driven 10 to 14
feet wide on 50- to 100-foot centres. Crosscuts are driven the same width as
the headings and on the same centres.
Side or face entries are turned to the right and left off the main entry at
1,100- to 2,400-foot intervals. These side entries consist of three to six
headings. An average panel is 1,200 to 1,000 feet wide by 1,800 to 2,400 feet
long.
Room entries consisting of two headings are driven off the side or face entries
on centres to conform to the length of the room, usually 240 to 300 feet.
Barrier pillars 100 to 500 feet wide are left to protect the main and face
entries. The first room is turned after the room entry is completed. Rooms are
turned on 60-to 100-foot centres in one direction only, and crosscuts are
driven between rooms on the same centres. The rooms are 10 to 18 feet wide.
As soon as the first room is completed, extraction of the pillar is begun. The
pillar line retreats along a line approximately 45° from the room entry.
Pillars are withdrawn by making successive cuts and slabs. All of the pillar is
removed except a few thin fenders and stumps between adjacent cuts, which are
left to protect the miners.
All working places are timbered, but as pillar extraction progresses break rows
of timber are usually set and part of the timbers are pulled to cause falls.
Room-and-Pillar — Advanced Robbing.
A method termed "full advance" is used in some mines. In this method
the pillars are drawn as the room entries or butt entries are advanced. The
area is developed by main entries consisting of three or more headings. Side or
face entries consisting of three or more headings are turned off the mains. The
distance between the latter ranges from 1,000 to 1,800 feet. Butt or room
entries are turned off the face or side entries in pairs at approximately
500-foot intervals. All headings are usually 10 feet wide. Barrier pillars are
left to protect main and face entries. The thickness of these pillars ranges
from 20 to 125 feet.
Rooms are turned off both butt entries on approximately 34-foot centres and
driven to an average depth of 238 feet. As soon as a room is completed,
extraction of the pillar is begun. Pillars are usually withdrawn by making cuts
averaging 17 feet in width through the pillar, leaving small fenders. These
fenders, which average 4 feet in width, are recovered by pick work when roof
conditions permit.
Room-and-Pillar — Retreat Robbing.
Another system in use at some mines is characterised by full development of
room or butt entries before rooms are turned off. The side or face entries are
turned off the main entries 1,400 to 1,800 feet apart. These face entries
usually consist of three or four headings. The room or butt entries, which are
driven with two headings, are turned off the face entries on approximately
550-foot centres. These butt entries are driven to the barrier pillar of the
next face entry. Barrier pillars which average 150 feet in width are left to
protect the face and haulage entries. The first rooms are turned at the face of
the butt entries adjacent to the barrier pillar. Room centres range from 45 to
90 feet. The length of the rooms is 200 to 250 feet. When three or four rooms
have been driven on each side, pillar extraction begins near the face of the
first rooms driven. The closed-end method of pillar extraction is ordinarily
used, and the fenders are removed when possible by pick mining. This mining
method is sometimes called "full retreat with short fracture lines."
There are mines where long faces are worked, using some mechanical means of
loading. The majority of mines, however, use some plan of room-and-pillar
mining.
Stripping.
Strip mining is conducted in some parts of the State where the coal seam
outcrops along the sides of valleys. The coal bed lies comparatively level, and
the slope of the hillsides is a governing factor in limiting the width of the
strippable areas. The economic depth of stripping in these areas averages 50
feet, but a depth of 72 feet has been excavated for short distances.
Power shovels are used to remove the overburden, and the opening cut, which is
70 to 80 feet wide, is usually made approximately 80 feet back from the
outcrop, where the overburden is 8 to 10 feet thick. It has been found that at
this distance and under this cover the quality of the coal is uniform. The
excavated material is wasted on the surface toward the outcrop. The coal
usually is removed from half the width of the initial cut, and the stripping
shovel deposits the spoil from succeeding cuts on the area from which the coal
has been removed. When the overburden is 25 feet or more thick, it is usually
necessary to drill and blast to prepare it for removal by the stripping shovel.
The coal is loaded by power coal-loading shovels, which follow the stripping
shovel. Cuts range from 40 to 50 feet in width. Rail haulage is used, and the
track is placed on the coal berm adjacent to the loading shovel. Loaded cars
are hauled in trips to the tipple with steam locomotives. The mines are usually
self-draining, but gasoline-driven pumps are available for an emergency.
Haulage and Ventilation.
Coal is usually transported in mine cars over track of various gauges. Most
mines use cars of steel or wood with a capacity of 1 to 4 tons. Steel
construction is commonly used for cars of large capacity. Gathering of the mine
cars from loading points to sidetracks or partings is done by animals (horses
and mules) or by electric gathering locomotives of various types
(storage-battery, cable-reel, or crab-reel). As a rule, electric trolley-type
locomotives haul the cars in trips from the sidetracks or partings to the mine
portal or bottom of the shaft or slope. This haul averages between 2 and 3
miles. Gathering locomotives have a speed of about 4 to 6 miles per hour, and
main-haulage locomotives about 8 to 12 miles per hour under full load.
Practically all mines are ventilated by fans, of which there are a number of
different types. Most of them are disc, centrifugal, or propeller fans. The
centrifugal fans have forward-curved blades, backward-curved blades, or radial
blades. The fans are either steam- or electrically driven, except that at a few
mines fans are driven by gas or gasoline engines.
Important Coal Beds.
The Pittsburgh is the most important coal bed mined in Pennsylvania. It is of
uniform thickness and physical qualities in any given area. Generally it
consists of two divisions, the roof coal and the lower division. The roof coal
is from a few inches to 8 feet thick, and is usually so broken up with shale
and clay partings that it is considered unminable. A clay parting separates the
roof coal from the lower division. The lower division is 3½ to 11 feet
thick and is usually divided by shale or bone partings into four benches (from
top downwards) — upper or breast, bearing-in, brick, and bottom coal. The
upper or breast coal is generally the best part of the bed, averaging about 4
feet of clean coal. At some places part of this upper bench is left for a roof,
but where the draw slate is exposed it is always taken down. The bearing-in
bench is 2 to 8 inches thick. It was given this name because the pick miner
worked in on this portion of the bed. The brick coal has cleavage planes that
tend to break it into brick-shaped blocks. It is from a few inches to 4 feet
thick and usually of good quality, although there are some places where it is
impure and not mined. The bottom coal is of poor quality, averages about 12
inches in thickness, and is generally left to protect the fireclay bottom.
Other of the more important coal beds are as follows : Lower Kittanning, Lower
Freeport, Upper Freeport, and Upper Kittanning.
Coal losses may occur in any of the following ways : (1) Coal left in roof and
bottom; (2) Coal lost from natural physical conditions, such as rolls, clay
veins, bad top, etc. ; (3) Coal left in pillars for protection in mining or to
protect a surface area ; (4) Coal lost in handling and preparation.
In 1935 coal loaded mechanically comprised 7.1 per cent. of the total
production. Mobile loaders, scrapers, conveyors equipped with duckbills, and
other self-loading heads handled 1.6 per cent., and pit-car loaders and
conveyors on which the coal was placed by hand loaded 5.6 per cent.
An average of 74.9 per cent. of the production from the State was undercut with
machines, 21.9 per cent. was mined by hand, and 2.6 per cent. was shot off the
solid.
Black powder, both granular and pellet, permissible explosives, and Cardox (a
carbon dioxide bomb which breaks the coal by a gas expansion method) are used
in the bituminous mines of Pennsylvania. Except in mines where shooting off the
solid is practised, the faces are cut with electrically operated cutting
machines before drilling. In the majority of the mines the coal is undercut at
the floor or slightly above it. In a few mines combination shearing and cutting
machines are employed.
The faces are drilled with an auger-type drill. Holes are located to suit the
mining and physical conditions in the mines, with reference to roof, impurities
in the bed, and sizes of coal desired.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Anderson, Robert L. | | U.S. Bureau of Mines | |
| Toenges, Albert L. | | U.S. Bureau of Mines | |