Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

5th October 1940, Page: 105, Column: 2

Superheated Steam

Of the source of waste in an engine the condensation of steam from the cooling effects of the cylinder walls, or cylinder condensation as it is called, is by far the greatest. This was recognised even early in the last century, but in 1855, for the first time, the extent of this loss was established in a definite manner by Hirn. It has been established, practically, that in an ordinary single cylinder non-condensing engine the amount of waste through cylinder condensation amounts, with an early cut-off, to from 35 to 40 per cent. of the total steam used. The best means of partially or wholly preventing this loss is by the use of superheated steam.

Steam is said to be superheated when, at any given boiler pressure, it has a higher temperature than the water from which it was evaporated. Moisture, no matter from what cause arising, cannot exist in the presence of superheated steam ; it robs the steam of its extra heat, and is itself evaporated into steam. The temperature of saturated steam cannot be raised without increasing its pressure ; but the temperature of superheated steam allowed to expand can be raised without increasing the pressure. Expansion is provided for by the steam being drawn off and used, or, if no steam is used, by the safety valve lifting.

The "rationale" of the use of superheated steam is not only the prevention of loss through condensation in steam pipes, but the addition of such an amount of superheat in the steam before it enters the cylinder as will make up for that robbed by the cylinder walls, so that the steam will remain practically dry, at all events up to the point of cut-off.

The principle on which a superheater should be constructed to give a sufficiently high temperature are :—

Firstly : The necessity of placing the superheater in a position where a suitable temperature is available. If a boiler is working under economical conditions the difference between the temperature of saturated steam, and of the escaping flue gases leaving a boiler, is not sufficient to superheat the steam produced unless the surface of the superheater be very large ; hence, generally speaking, a superheater should not be placed in the flue between boiler and chimney. On the other hand, if placed too near the boiler furnace, possibly damage would result from the impact of flame.

Secondly : The superheater should be constructed to admit of all its parts expanding and contracting freely, without severe strains being put on any of the joints, which might cause them to leak ; flanged joints, when exposed to furnace gases, should be avoided wherever possible.

Thirdly : Provision should be made to protect the superheater against overheating when steam is not, passing through it sufficiently to carry away the heat supplied by the furnace gases.

Experience has led to the following conditions to which the construction of an independently fired, or "separate furnace" superheater should conform :—

(1) It should be made entirely of wrought steel, with tubes small in diameter, seamless, and thick.

(2) No perishable packing, such as asbestos, should be used for any joints.

(3) The steam should be circulated rapidly.

(4) The areas through which the steam passes should be considerably in excess of the steam inlet and outlet connections to avoid drop in pressure.

(5) The tubes should not be subjected to the direct impact of the furnace gases, but should be in a chamber filled evenly with Completely burnt gases of as low a temperature as practical to ensure the final superheat required.

(6) It follows that a large heating surface and a low rate of heat transmission should be provided, say about 2,200 B.T.U. per square foot of surface per hour.

(7) The entire construction should offer the greatest freedom or expansion and contraction.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Hirn, —      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print