5th October 1940, Page: 101, Column: 1
Fireproofing Mine Shafts
This is the subject dealt with by Mr. Jos. R. Guiteras in Information
Circular 7075 of the U.S. Bureau of Mines. He says that fireproofing a mine
shaft implies lining the shaft with fireproof material or rendering fireproof
the materials already composing the shaft lining. Reference is made to the
procedure followed by Anaconda and other mining companies in carrying out their
fire-prevention programmes, the standard applications of fireproof construction
including the use of (1) steel shaft sets, (2) precast reinforced concrete
shaft sets, (3) concrete rings, (4) continuous concrete lining, and (5) gunite.
Steel Shaft Sets. — Steel sets are of structural shapes. Wall
plates, end plates, and dividers usually are H-sections with the flanges
vertical. Posts are made of angles. Guides usually are made of wood but
sometimes are of steel; safety dogs on cages get a better grip on wooden
guides. As much of the set as possible is shop-riveted ; the rest is bolted in
place. Steel sets sometimes are coated with gunite, poultry wire being used as
reinforcement.
Precast Reinforced-Concrete Shaft Sets. — Precast
reinforced-concrete sets have members corresponding to those of timber sets,
and have been used successfully in both vertical and inclined shafts.
Concrete Rings. — The ring method makes use of a monolithic
concrete lining in horizontal bands separated by intervals of bare rock.
Continuous Concrete Lining. — This type of lining usually is
poured to rock but sometimes is formed in the clear and anchored at intervals,
in which case the intervening space may be backfilled. Concrete mixtures
ordinarily used range from 1:2:4 to 1:3:6, and the thickness ranges from 8 to
18 inches. The lining usually is placed from the bottom upward, but there may
be several points of attack to keep the crew busy. Mixing usually is done at
the surface, especially on large jobs ; it sometimes is done underground.
Reinforcement of lining usually consists of ½- or ¾-inch bars, either
round or square. The horizontal bars are spaced 6 to 9 inches apart; the
vertical bars, about 24 inches apart. Masonry linings, including concrete
blocks, have been used in Europe, but concreting is preferred in the United
States.
Gunite. — Gunite is a mixture of sand and cement applied wet under
air pressure by means of a cement gun. It may be used to preserve steel or to
preserve or fireproof timber. The material to be gunited is covered with wire
mesh or expanded-steel lath. Mixtures range from 1 part of cement to 2½
parts of sand to 1:5 at the gun. One bag of cement yields 32 square feet of a
1:4½ mixture or 22 square feet of a 1:3 mixture, 1 inch thick. Sand should
be minus ¼ inch. The usual sizes of gun require 110 to 225 cubic feet of
free air per minute at 40 to 75 pounds per square inch pressure.
In the summary of fireproofing measures recommended as a result of lessons that
have been learned Mr. Guiteras includes—
The safest surface construction is a steel headframe with a steel and concrete
shaft collar to a depth of 25 feet.
Surface structures near a shaft should be of incombustible material or
fireproofed and protected by a sprinkler system; otherwise, surface structures
should be at least 100 feet from the shaft.
A steel door should be placed at the shaft collar.
All shafts, stations, landings, and shaft bottoms should be lined with
fireproof material. It is more important to fireproof shaft bottoms and
landings than the shaft itself. If a mine has a long life, concreting may not
be an additional expense. Downcast shafts often are dry and should be lined
with concrete. If shifting ground makes a concrete lining impractical, the
timbered shaft should be fireproofed with gunite.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Guiteras, Joseph R. | | U.S. Bureau of Mines | |