|
5th October 1940, Page: 98, Column: 2 Electrical NotesArc Lamps. It is recalled that the first arc lamp was constructed by Sir Humphry Davy. It consisted merely of two short pieces of light wood carbon attached to a battery of 2,000 primary cells of imperfect type. It is common knowledge that if two pieces of carbon (or other conductor) be employed to complete an electrical circuit of suitable E.M.F. an arc will be set up immediately the carbons are drawn slightly apart. A crude form of arc lamp can be made by clamping the carbons in holders and providing mechanism so that one carbon can, at will, be approached to, or receded from, the other. As a matter of fact, in some types of projectors for stage and searchlight purposes this was the only mechanism employed. Naturally, such an arc lamp has the decided drawback of requiring constant attendance, and would be useless for the various purposes for which arc lamps are now generally employed.
Alternating Currents. An alternating current, as the name implies, is one which, instead of flowing always in one direction, flows alternately in opposite directions round a circuit. In other words, the current is rapidly reversed, rising and falling in a succession of impulses or waves so that under the influence of a rapidly reversing electromotive force electricity is oscillated backwards and forwards with enormous rapidity through the circuit. It is clear that such a general definition can be made to include a great many kinds of alternating currents, and each kind requires separate treatment. The laws governing the flow of such a current through a circuit are, to a very large extent, dependent on the rate of change, the variation of which both in direction and magnitude may be very different. This variation may be sudden or gradual, uniform or irregular. Take, for instance, the change of direction. This change may be made once in a hundredth of a second, once a second, or once an hour, and although we may have the same total quantity of electricity flowing first in one direction and then in the other, the potential difference requisite to send it through the circuit will be very different. It will, in fact, vary with the different gradations of change. In the alternating current dynamo or alternator, as it is usually called, the electromotive force rises and falls in a rapid periodic fashion, in most cases less than one-tenth of a second. The time taken for one complete to-and-fro alternation of the current is called one period, and the number of such periods, or double reversals of the current in a second, is called the frequency, and sometimes the periodicity. The properties of alternate currents differ in many material respects from those of direct or continuous currents. From a constructional point of view the alternator is simplicity itself when compared with the direct current generator; nevertheless, it is true that the physical theory of the former is complicated by the consideration of certain properties and principles which in no way affect that of the latter. Take an instance. Alternate currents are affected not only by the resistance of the circuit, but also by its inertia or self-induction. This latter property diminishes the amplitude of the waves, and retards what is known as their phase. The electromotive force of an alternating current is usually expressed : E = D sin Ø, where D is the maximum value of amplitude attained by E, and Ø an angle of phase upon an imaginary circle of reference. This is the mathematical expression of the sine law. When speaking of direct or continuous currents through any circuit all we require to know is the resistance of the circuit, and we can at once determine the strength of the current which will flow under the influence of any given potential difference. In the case of alternating currents other properties of the circuit must be taken into consideration. Take the more simple case of a continuous or direct current circuit which is "made" and "broken." Faraday's experiments on electromagnetic induction showed that if two coils of wire are held near each other in parallel planes, the starting of a current in one will induce an E.M.F. in the other coil. Further, from Lenz's law we can determine the current flowing in the second coil. It will be opposite in direction to that in the primary or inducing coil. When the current in the latter is broken the effect will be reversed. The explanation is that when the current is started in the primary coil, lines of force are produced which thread the second coil, and an E.M.F. is induced in the secondary. This E.M.F. is equal to the rate of change of the number of lines threaded by that coil. When there is no change in the number of lines of force, or, in other words, when the current is steady, there is no E.M.F. induced. When the circuit is broken, the direction of the E.M.F. is reversed. When the current is started in one coil there will be an opposing E.M.F. induced which tends to retard the flow of the current; and when the current is stopped there is induced an E.M.F. tending to keep the current flowing. These electromotive forces are said to be due to the self-induction of the circuit, and the coefficient of self-induction is determined by the magnitude of the back E.M.F. induced when the current is changing at a given rate. The unit of self-induction is called the Henry, and is defined as follows : A coil of wire is said to have a coefficient of self-induction of one henry if the back electromotive force induced, when the current is changing at the rate of one ampere per second, be one volt. When the current is started through a coil the effect produced by self-induction is to retard the flow of current, which, instead of rising to its full steady value, as determined by Ohm's law, only increases gradually. Theoretically, it only attains this value after an infinite time. Take, for example, the time taken by the current to reach nine-tenths of its full value round a coil. With a self-induction coefficient of 100 henrys and a resistance of 10 ohms, the time taken is 23 seconds. The introduction of iron into a coil greatly complicates matters owing to the varying permeability of different kinds of iron. Assume that the shunt circuit of a dynamo is suddenly broken by means of a quick break switch. The magnitude of the potential difference is determined exactly in the same way as when the current is increasing, but with this difference : the resultant E.M.F. will be in such a direction as to keep the current flowing in the same direction as formerly. The actual voltage induced can be calculated by multiplying the coefficient of the self-induction of the circuit by the rate of change of the current flowing through it. Consider as an example the shunt circuit of a dynamo having a resistance of 10 ohms, and a self-induction of 100 henrys. A current of 10 amperes is destroyed in one-tenth of a second. The rate of change is obviously 100 amperes per second, and applying the rule, we have 100 amperes (rate of change) X 100 henrys (coefficient of self-induction) = 10,000 volts. This represents a pressure 100 times as great as is required to send a steady current through the coils, and shows at once the great danger of too suddenly breaking a highly-inductive circuit. It is true that it would be impossible in practice to break the circuit as quickly as is assumed, owing to the inevitable formation of an arc at the terminals of the switch, but the calculation is sufficiently accurate to show the necessity for caution in breaking highly-inductive circuits. In the case of a non-inductive resistance, that is, a circuit with a certain amount of resistance, but without self-induction, the calculations are, of course, determined simply by Ohm's law. The effect of self-induction is to retard the rise and fall of the current. If we were to take a number of sheets of tinfoil, connected alternately with each other, and separated by sheets of mica or paraffined paper, so as to form or make what is known as a condenser, and connect this up to a source of direct or continuous current, we should find that when the circuit is made there is a sudden rush of current into this condenser. This "quantity" is determined by the equation Q = C E, in which C is the capacity, and E the electromotive force of the source of supply. When the full potential difference has been attained the flow of current will cease, and if the current be then broken the condenser will remain charged. If the source of supply be removed, and the two terminal points or terminals be brought together, there will be a corresponding rush of current flowing ; this time, however, in the opposite direction. The amount flowing will be the same, neglecting leakage, as that originally sent into the condenser when on charge, i.e., Q = C E. The microfarad, or one millionth of a farad, is the practical unit of capacity. The coulomb is the unit of quantity of current. The practical unit of current strength or rate of delivery is, of course, the ampere. It is that strength of current which is developed in a circuit of one ohm resistance by an electromotive force of one volt. If this current is maintained for one second one unit of electrical quantity is delivered, and this unit is called the coulomb. — P.T.W.
|
|||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||