Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

21st September 1940, Page: 85, Column: 1

Drilling Dust Problems

Extracts from paper presented at the annual general meeting of the Chemical, Metallurgical and Mining Society of South Africa.

By G. Hildick-Smith.

Prior to the use of the thermal precipitator on the Rand five years ago we were in the dark as to the exact quantities and size frequencies of the dust produced by the various underground operations, although it was known that dust particles of less than five microns Were the dangerous ones. As the result of the work of Mr. H. S. Patterson, scientist to the Chamber of Mines, with the thermal precipitator in determining which underground operations produce dangerous dust, we know that, excluding blasting dust, the only dangerous dust produced regularly and in sufficient quantities to be dangerous — to those Working in the vicinity — is that made by drilling operations.

In drilling, dangerous dust is produced :—

1. By the impact of the borer bit at the bottom of the hole, at the rate — with the present types of hammer machine drills — of approximately 1,800 blows per minute with compressed air at 60 lb. pressure per square inch and over and with a blow of about 42 ft.-lb.

2. By the atomisation — through the machine-drill release ports — of the water used for allaying the dust produced by the borer bit; such water may carry particles of silica in suspension varying in number from several hundreds of thousands to as many millions per c.c.

The atomisation of water through the release ports also releases colloidal silica and is also a prolific cause of the humidity of the underground air.

With regard to the dust made by the borer bit it must be remembered that the energy of the blow is exerted over the small area of the cutting edges, hence the fineness of the dust produced.

Since the use of the present type of hammer machine-drills became standard practice on the mines various methods have been tried for preventing the drilling dust getting into the mine air ; of these the more important were—

1. The fronthead water-feed ;

2. The release ports in the fronthead of the hammer machine-drill ;

3. The long piston hammer machine-drill.

It has long been known, due to the dust-sampling methods in vogue prior to the use of the thermal precipitator, that the quantity of drilling dust produced depended to some extent on the amount of air passing down the hollow borer.

About three years ago Patterson made experiments to determine the thermal precipitator counts of the dust produced in drilling with a machine fitted with a fronthead water-feed of the Holmes box type. The machine was tested rigged and produced a negligible amount of dust, as no air, with this type of water-feed, could pass down the borer. The drilling speed of the machine and the humidity-producing effect were satisfactory. It seemed therefore that it was worth while again trying to make the principle of the fronthead water-feed of practical use.

It was necessary to consider how the standard types of hammer machine drills could best be adapted so as to reduce their drilling dust-making properties. As a result, about a year ago it was arranged that the original type of long piston machine should be given a thermal precipitator test. The dust results obtained were such as to warrant further investigation, although in the tests the drilling speed was about 16 per cent. slower than that of a similar type of standard machine. Before studying further the dust side of the problem it was essential to endeavour to obtain a drilling speed equal to that of the standard type of machine drill.

Long piston machines have been giving satisfactory results in practice for several months, and it is safe to say that in so far as drilling speed is concerned they can be made to give all-round drilling speeds equal to those of the standard types of machines.

The problem of drilling speed having been overcome, the question of conducting experiments to determine the long piston machine's dust-making properties was considered. Any difference in regard to such results as compared with the fronthead water-feed machine could only be due to :—

1. Air passing down the hollow borer and returning in the form of bubbles containing dust, through the water in the hole, and bursting and releasing the dust when leaving the water.

2. The atomisation of water containing fine particles of silica through the release ports.

Dust in the exhaust air from the machine is common to both types of machines and normally may amount to 50 particles per c.c. per 1,000 cubic feet of air passing per minute, but may at times be much greater due to dirty pipes, etc.

The production of dust by the atomisation of water through the release ports can be prevented by having release ports of sufficient area to prevent atomisation, provided that water is not allowed to run over the exhaust port and thus become atomised. The main problem was, therefore, to prevent air passing down the borer.

With the use of the long piston machine the quantity of air passing down the borer chiefly depends on the clearance between the water tube and the hole in the front end of the piston, and the dust produced in drilling with this type of machine directly depends on this factor unless an internally flared water tube is used, by means of which it is possible to prevent air flow down the borer except in negligible quantities with clearances up to 20/1,000 inch.

Having placed a machine drill as it seems possible in a condition in which it will only produce either no dangerous dust or a negligible quantity of dust, it must of course be kept in that condition day in and day out when at work. On all mines there is at present a regular system in regard to machine repair, the repair shops being usually equipped with a rotation testing apparatus, air meter, etc.

There are several ways of combining the various factors in a a hammer machine-drill so that when in operation it will not pass more than 100 c.c. of air per minute down the borer.

Fitted with a standard water tube, with a clearance of up to 7/1,000 inch between tube and piston, the long piston machine will pass less than 100 c.c. of air down the borer, but with greater clearances the quantity of air passing increases to such an extent that a dangerous quantity of dust would be produced.

It would be impracticable to keep machine drills in regular operation with as little as 7/1,000 inch clearance between water tube and piston, and thus.it seems that the use of internally flared water tubes would overcome this difficulty.

In order to keep safely within the standard 100 c.c. of air per minute passing down the borer it will be necessary to use water tubes with inside diameters of 7/32-inch and outside diameters of 0.375 (3/8)-inch if machine drills with clearances between tube and piston of up to 20/1,000 inch are to be successfully prevented from causing the production of dangerous quantities of dust.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Hildick-Smith, G.      
Patterson, H. S.      



Related Articles

Pub.
Date
Article (Newspaper)
21 Sep 1940  Drilling Dust Problems (The Science and Art of Mining)
18 Oct 1941  Drilling Dust Problems, South African Engineers' Discussion (The Science and Art of Mining)

 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print