Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

7th September 1940, Page: 70, Column: 1

Dust And Slurry Problems

In his paper on "The Preparation of Coal for the Market" in the Journal of the Sheffield University Mining Society, Mr. L. W. Needham, M.Sc., deals with dust and slurry problems as under :—

It has long been realised that no coal cleaning process except froth flotation is effective in cleaning the finest sizes of coal. Claims are sometimes made for cleaning by wet processes down to .01 inch, but it is perhaps more accurate to claim cleaning down to .02 inch. Dry cleaning is less efficient from this point of view, and even specially designed dry cleaners do not accomplish any appreciable cleaning on sizes below about .05 inch.

In addition to not being cleaned, the coal below say .02 inch is difficult to recover after once being put into the circulating water of a washer. A corresponding problem occurs in dry cleaning where the recovery of dust removed from the coal at some stage in the cleaning process has to be considered.

The problem of dealing with the finest sizes of coal is common to all kinds of washers, and it may be discussed in general terms. So far as wet processes are concerned, the general practice is to remove the clean products, on a succession of screens, which also pass the water associated with the products. Normally, a slack product is collected on wedge wire screens having an opening of about .75 mm., and the water and fine particles passing this screen are pumped to a large settling cone. Solids settling in this cone are dewatered on slurry screens, also usually of wedge wire having an opening of about .25 mm. Coal collected on these screens may be referred to as coarse slurry. The finest screens, however, must pass some fine particles as well as water, so that, unless steps are taken to remove particles passing the finest screen, an accumulation of them will take place in the washery water until the concentration of solids is so high that cleaning is adversely affected. The traditional method of removing such fine solids from the system is to run out of the circuit part of the water either continuously or periodically and to allow the solids to settle in ponds for subsequent collection. This is a crude and expensive expedient, and modern washeries are almost always provided with a water clarification plant for the recovery of the finest solids not removed by screens. The term fine slurry may be used for the solids which cannot be screened out of the water.

Such a plant consists essentially of a thickener and filter. The thickener is a settling tank in which complete precipitation of the fine slurry is achieved by addition of flocculating reagents. The filter is used to dewater the settled solids in the thickener and to obtain a filter cake in a reasonably dry and handleable condition. By reason of the complete precipitation of the solids the water entering the thickener is completely clarified, and may be returned to the washery for use in spraying the products.

A properly designed clarification plant will ensure the recovery of fine slurry in a satisfactory form and the maintenance of good conditions in the washery water throughout the system. It will bring about a stabilisation of the concentration of the solids in the washery water, consequently more uniform conditions and frequently, as a result, better cleaning of the coal.

Dedusting of the raw coal prior to cleaning it by wet methods was introduced mainly as a means of minimising slurry difficulties. Obviously, if a proportion of the slurry-forming material can be removed before the coal is treated, the amount of slurry produced will be decreased. It is impossible, however, to avoid the production of slurry altogether by dedusting, and it should be realised that the removal of dust beforehand does not prevent the accumulation of solids in the washery water which is a consequence of the impossibility of screening out all the solids present. Since the introduction of reliable water clarification plants, the argument for dedusting is rather weakened, except where it is desirable to mix dry dust with clean slack for the reduction of moisture content. In some cases, of course, dust removed is so high in ash content that mixing back is not permissible, and since in practice the dust taken out always contains some coal above .01 inch it is generally better to allow the whole of the coal to go into the washer and to provide proper equipment for the removal of fine particles. Furthermore, effective dedusting is only possible when the raw coal is reasonably dry and, generally speaking, coals containing more than about 3 per cent. of surface moisture cannot be dedusted efficiently.

When conditions are suitable for dedusting and the market requirements support its adoption, it is possible to remove the .01 inch — 0 fraction with a high degree of efficiency. The Lessing deduster, in which coal is dedusted by a substantially vertical stream of air into which it falls and the dust is subsequently classified into fine dust and medium fines, is established as the most efficient deduster.

In pneumatic dedusting it is possible to remove all the dust at the expense of removing at the same time considerable amounts of much coarser particles. It is also possible to ensure that no coarse particles are removed at the cost of leaving in the coal some of the dust. A deduster has therefore to be adjusted to give a reasonable compromise, that is, to extract as much as possible of the dust (.01 inch — 0) with only a reasonable proportion of oversize. Usually coal sized between ¼ inch — 0 and about ¾ inch — 0 is fed into a deduster, and for raw coal containing about 6 per cent. of .01 inch — 0 the dedusted coal should not contain more than about 1 per cent. of .01 inch — 0 and dust not more than about 20 per cent. bigger than .01 inch and 5 per cent. bigger than .02 inch. This performance must be considered satisfactory when the very varying conditions of loading and moisture content normally encountered are taken into account.

Recovery of the dust after removal from coal before cleaning may be accomplished by cyclones or some form of air filter. It is usually necessary to ensure a reasonably clean effluent in order to avoid complaints of dust nuisance. Though many plants meet this condition satisfactorily, difficulties are sometimes encountered in the recovery of dust from certain extremely dry coals.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Needham, L. W.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print