27th July 1940, Page: 20, Column: 1
Tramming And Hauling In Metal Mines
Metal Mining Practice is the subject discussed by Charles F. Jackson and
J. H. Hedges in Bulletin 419 of the U.S. Bureau of Mines. This document
of over 500 pages is obtainable at 60 cents (net) through the Superintendent of
Documents, Washington, D.C., to whom inquiries should first be sent. The
discussions of the various aspects of the question, together with the
accompanying data, are based on information gathered and studies made during
the period 1928-1938. The 156 illustrations and 63 tables add to the value of
the Bulletin, which should strongly appeal to coal mining students who desire
to add to their qualifications some knowledge of metal mining practice. The
main subjects dealt with include Prospecting and Exploration ; Sampling of Ore
Deposits ; Estimation of Ore Reserves ; Mine Development; Transportation of Ore
and Waste ; Stoping ; Surface Mining ; and Ore Dressing.
Extracts from the section on tramming and hauling are appended.
Hand Tramming.
Hand tramming is still widely used in small mines, in prospecting operations,
and as an adjunct to mechanical haulage systems. For tramming small tonnages of
rock and ore short distances on the main levels, for short transfers on
sublevels, and in some types of stopes it is the obvious method to employ,
although, if power is available, scrapers may be more economical for some of
these purposes and small storage-battery locomotives for others, provided the
tonnage to be handled warrants the capital outlay involved.
Hand tramming requires a minimum capital investment for equipment and for this
reason, among others, is particularly adapted to prospects and small-scale
operations such as those conducted by many "leasers" (lessees).
Small cars of 12-, 16-, or 20-cubic foot capacity are usually employed, the 16-
and 20-cubic-foot sizes being the most popular, although cars holding 2 to
2½ tons are sometimes used. In the Tri-State lead and zinc district,
"cans" of 1,200 to 1,400 pounds capacity were used almost exclusively
for many years, but more recently these have been superseded by cars in some of
the mines. The cans are buckets that are run to the face on a flat track and,
after they have been loaded, are returned to the shaft and hoisted directly to
the surface.
Cars are usually of either the end- or side-dumping type, with the end or one
side, as the case may be, forming a swinging door suspended from a rod at the
top of the car and latched at the bottom. In the end-dump type the car body or
box is often mounted on a turntable on top of the truck frame, so that the car
may be turned for dumping into a chute at either side of the track.
Car bodies and truck frames may be of either wood or steel construction, though
few wood cars have been employed in recent years. One advantage of the wood-box
car is that if a board becomes broken it can readily be removed and replaced,
whereas a damaged steel box requires considerable work in the shop.
For tramming ore and filling material in cut-and-fill stopes, a car with a
scoop-shaped box open at the front end may be used to advantage.
Tracks for hand tramming are laid usually with light rail (weighing 8, 12, or
16 pounds per yard) on wood ties. The heavier rails are preferable if they are
to be used for an appreciable time, since once they are well-laid they are less
likely to become bent and out of alignment and thus will require less
attention.
Track grades for most efficient hand tramming should be considerably steeper
than for locomotive haulage. The ideal grade would probably be that on which
the effort required to push a loaded car downgrade would equal that required to
push the empty car up, although some prefer a somewhat steeper grade, so that
the loaded car, when once started, will almost if not quite run by itself. The
exact grade requiring a minimum of effort will vary with the size and weight of
the car and the load carried, the type of bearings, lubrication, and the
general condition of the equipment and track. Ordinarily, grades of 1 to
1½ per cent. in favour of the loaded cars will be found satisfactory for
hand tramming.
Animal Haulage.
Mules and horses continue to be employed for underground haulage, though much
less extensively than formerly. The growing availability of electric power, the
introduction of Diesel generating plants in sizes and of capacities to suit
almost any condition, and the development of small storage-battery and trolley
locomotives have favoured the substitution of mechanical for animal haulage.
Animals are useful for gathering loaded cars from the loading faces to a siding
on the main haulageway and returning the empties, particularly if large cars
are employed or there are unavoidable grades to be negotiated that are too
difficult for hand tramming but not steep enough for rope haulage. Cars may be
handled one at a time or be made up into trains of two, three, or more,
depending on conditions.
As a rule, mules are preferred to horses for underground work, and for heavy
work animals weighing around 1,200 pounds are more satisfactory than smaller
ones, provided there is enough head room. Smaller animals, of course, must be
employed where head room is low or larger ones cannot be taken down the shaft.
A cage compartment usually will accommodate a 900-pound mule.
Mechanical Haulage.
In considering mechanical v. hand or animal haulage in a mine or section of a
mine, a factor that always must be considered is the duty to be performed. If
there are no other mitigating conditions, it is a good general rule that for a
locomotive (or any type of machine) to pay for itself it must be kept busy ; in
other words, idle machines pay no dividends. When mechanical haulage units can
be kept busy they will usually show a saving in operating costs as compared
with hand or animal tramming.
Mechanical haulage in metal mines is of four general types : (1) Locomotive,
(2) scraper or slusher, (3) rope, and (4) belt conveyor.
Locomotives for underground use are powered by electric, compressed-air, or,
rarely, gasoline motors. Diesel locomotives have been used extensively in
Europe, but have not been adopted in the United States. Studies are now in
progress on how to adapt American Diesel locomotives to underground use and to
determine conditions under which they may be employed with safety. Gasoline
motors should never be employed for underground work because of the hazard from
exhaust fumes.
Electric locomotives are either of the trolley or storage-battery type, and
each has its particular field. For long hauls and heavy trains the trolley type
usually has a decided advantage, whereas for shorter hauls, such as in
gathering service from a number of loading points to a main haulageway, the
storage-battery type may be preferred. Small storage-battery locomotives of the
"trammer" type that can be run on the mine cage and transferred
quickly from one level to another have found wide favour where the mine output
is small and comes from scattered areas and several horizons in the mine. For
heavy duty, storage-battery locomotives have insufficient ampere-hour capacity
for long service without frequent recharging, and spare batteries may have to
be supplied for each locomotive. Where haulage is confined to one shift the
batteries may be charged on the opposite shift. When charging can be done
between shifts or at times when the total mine load is light, storage-battery
locomotives may have an advantage over trolley locomotives in keeping down
power peaks.
Cable-reel trolley locomotives are sometimes used for gathering in short
headings tributary to the main haulageways, where it does not pay to install
trolley wire.
Compressed-air locomotives have not been employed widely in metal mines but
have certain obvious advantages in gassy coal mines. Their over-all efficiency,
including that of the compressor unit, is low, and the cost of power for their
operation is high. In some instances they have been installed in preference to
trolley locomotives because of the hazard of exposed trolley wires,
particularly at loading chutes. They receive air at high pressures (600 to 850
pounds or more), which necessitates the installation of high-pressure
compressors, receivers, air mains, and charging equipment at high initial cost
and requires careful attention to prevent leakages and attendant loss of power.
Although the scraper as employed underground is ordinarily considered to be a
mucking and loading machine, it is also a conveying machine and in some
instances is used to transport ore and rock several hundred feet. It is then an
auxiliary part of the transport system for moving ore from the face to a chute
or mine cars or for transferring ore from a series of stope raises, through a
sublevel drift, to an ore pass.
The term "rope haulage" is used here to mean the use of hoists for
pulling cars on grades or flat slopes where the grade is too steep for
locomotives or the method in general use in the mine.
Conveyor systems have come into common use in coal mines during the past
decade. As this is written, belt conveyors are beginning to make their
appearance in metal mines as a part of the underground transportation system,
and an increasing number probably will be installed during the next few years.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Hedges, J. H. | | U.S. Bureau of Mines | |
| Jackson, Charles F. | | U.S. Bureau of Mines | |