Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

15th June 1940, Page: 396, Column: 1

Steel Propping Pointers

Further work has been done by the Safe Working in Mines Committee of the South Staffordshire and Warwickshire Institute of Mining Engineers, and a paper was read at the last meeting of the Institute by the Investigator, Mr. J. W. Robinson, on "Roof Control, Safety and Economy of Roof Supports," from which the following points are extracted :—

In the area covered by the Committee 89 per cent. of the steel props installed are of H-section and 11 per cent. tubular.

As pointed out by Mr. Robinson in the paper, H-section girder props should, where possible, be set with the web parallel to the direction in which the bending is most likely to occur. For instance, it has been found in inclined seams that the props suffer least damage from bending when set with their webs in the line of the direction of dip. In more or less flat seams the relative lateral movements of the roof and floor are usually in the direction at right angles to the face, and girder props may be expected to give the best service when set with their webs in that line. In practice, it is found that the best position of setting with plain H-section girder props is determined frequently by the direction of the tightening of the props.

When driving a prop into its final position, the hammer should strike the flange and not the web. If the web be struck the material may fail after a comparatively short life. Systematic setting and alignment are important factors, and uniform spacing has been proved to be the most effective method of reducing the buckling of props.

Convergence between the coal face and the edge of the waste during the period the props are set should be within the limits provided by suitable lids, floor penetration or other devices, to avoid distortion or breakage of the support. This applies equally so whether the supports be of wood, steel, concrete, or other substitute. The lids should be at least as large as the prop heads, and thick enough to provide cushioning.

Recent practice has shown that rectangular, or slightly tapered, hardwood lids offer more immediate resistance than those made from soft wood and give the best results — the taper assists in the setting and withdrawal. The hardwood lids also afford less yield and tend to split more readily than soft wood. The effectiveness of wood lids will be enhanced if placed between the steel prop and bar with the grain of the wood at right angles to the bar corrugations. The provision of a liberal supply of lids within easy accessible reach of each unit face is essential to the success of steel propping.

Systematic under-spragging has an important function in minimising the area of unsecured roof in any propping system. It is during the cutting period that the major amount of convergence takes place, and it emphasises the necessity of affording early and adequate support to the undercut coal.

Systematic setting and ready withdrawal of steel props demands careful supervision if losses are to be reduced to a minimum; in fact, they may be important factors in the economic application of steel supports.

Where rigid steel props are not provided with some form of releasing device, their withdrawal is generally more difficult than that of a timber prop. If set under corrugated bars with suitable wood lids, their withdrawal is greatly facilitated.

It has been found advantageous, where the height at the face permits, to institute a rack system for the storage of steel supports on the face. This system is also a means of preventing loss and, in addition, the supports can be easily checked. When such a rack system is not adopted, the withdrawn supports should always be placed on the floor on the face side of the conveyor.

The introduction of steel supports at the working face, particularly in seams where the adjacent strata are of a friable nature, has necessitated changes in the method of supporting the road sides. The two factors which have governed such a change are: (1) The scarcity of suitable "builders" owing to the soft nature of the adjacent strata; and (2) the supply of timber for building roadside chocks is not available when steel face supports are used. In these circumstances, dirt-filled bags have been used at a number of collieries with a definite improvement in roadway conditions — as a substitute for timber chocks or for walling stone in packs.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Robinson, J. W.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print