15th June 1940, Page: 394, Column: 1
Mine Lighting
By E. H. Gripton.
Extracts from paper on "The Evolution of the Miner's Flame
Safety-lamp" in the ANNUAL MAGAZINE of the Notts. Mining
Students' Association.
Wicks, Burners and Illuminants.
The desire to improve the lighting value of safety-lamps, as
well as the introduction of electric ignition and the use of petroleum
oils, has caused inventors to give much attention to the wick-holder
and the burner of the safety-lamp. Kaye introduced the
round wick to burn petroleum, and Ashworth introduced a burner
with double discs to put the pricker hole under cover. Porcelain
burners were introduced by Barton, Ackroyd and Best and also
by Ashworth. Porcelain or pot homers are of various shapes,
and their use tends to keep the oil vessel cooler than when metal
burners are used. The lighting power of a fixed quantity of oil
is also greater when applied through a porcelain burner than
through a metal one.
The material of which wicks are made is usually cotton, but
to obtain the best results for lighting purposes they should be soft
and open for thick oils such as colza and harder for thin oils such
as mineral colza and petroleum.
The introduction of electrical ignition and the use of porcelain
burners has necessitated attention to the most effective way of
receiving the electric spark from the conductor, and Ackroyd and
Best solved this by inserting a piece of metal foil inside the wick
used by them. To-day it is brought about by heating a wire
in close proximity to the top of the wick.
The light-giving power of a lamp is of great importance, as the
miner working with a good light can reduce the accident rate from
falls of ground by being better able to see the conditions of the
roof and sides.
Up to 1880 the universal opinion of all leading authorities on
illuminants for safety-lamps was that the only oils that could be
safely used in a safety-lamp were colza, rape and seal. A suitable
illuminant, of a mixture of two parts of colza to one of petroleum
(having a flash point not under 80°F.), was suggested by the
Mines Accidents Commission in 1886. Later inventions proved
that it was possible to use any illuminant, whether it was solid,
liquid or gaseous, providing the lamp was properly constructed
to burn the desired illuminant. Petroleum and benzolene were
also used, this type of illuminant being suitable for ignition by
electric current, owing to its evaporating power.
Types of Safety-lamp.
Makers have introduced lamps for general use of from four to
five candle-power, and in most cases the combustion tube has
again been introduced.
John Davis and Son (Derby) have a lamp on the market giving
from 4 to 5 C.P. at the beginning of the shift and 4 C.P. at the
end of nine hours burning. This type of lamp is known as the
"Haydock" and will burn fourteen hours, also its weight is quite
reasonable, being about 4¼ lb. It is fitted with a T. and S.
Haywood and Naylor combustion tube, the internal glass being
suspended from the top. This lamp is fitted with oil filling valve
and either magnetic or lead plug lock and can be fitted with
re-lighter pin and screw wick adjustment.
The high candle-power safety-lamps of the earlier type of this
series, while giving a good light, had a tendency to become hot,
especially in mines which were themselves abnormally hot. The
Davis firm have experimented with the aim of overcoming this
drawback and have produced the Davis Derby "Cooler" lamp
as a result. The " Cooler" lamp, although essentially a hewer's
lamp, is also an excellent gas tester. The candle-power of this
lamp is very high, but it can be varied according to the height of
the wick.
Davis and Son have also introduced the Davis Derby "Dwarf"
deputy flame safety-lamp. As its name indicates, it is a small
lamp for the special purpose of testing for the presence of gas.
A special feature of this lamp is the shut-off air ring with a releasing
pillar. The lamp is also fitted with an internal igniter, screw
wick adjustment and lead plug lock. It is constructed of steel
and brass and its total weight is only 2 lb.
The "Protector" lamps have also been improved similarly
the workmen's lamp being fitted with a combustion tube, and a
dome over the burner. The new type of officials' lamp is fitted
with an internal igniter and also a double gauze and shut off ring
over the bottom air inlet. When this inlet is closed the thin film
of gas or air near the roof is fed to the flame, the inlet air or gas
having to mix with the products of combustion before reaching
the flame.
The Hailwood combustion tube lamp has two gauzes, a magnetic
lock and spring action oil filling valve, also a pot or porcelain
burner. They have also an improved type similar in appearance
to this lamp but, like the Davis, have a perforated bonnet for
cooling purposes.
The Hailwood high candle-power flame safety-lamp is fitted
with a Hailwood patent swivel combustion tube, and like all
combustion tube lamps gives the best illumination results if a
mirrored glass reflector is used. For the miner the burner dome
is solid and simple, but for the fireman the dome is split and one
part may be lowered to expose the top of the wick tube, to see
the gas-testing flame against the black background of the fixed
half of the dome. These lamps are fitted with the Hailwood
patent cooling shields to the bonnet and vessel, enabling them
to be handled with the maximum of comfort. The top of the
bonnet is fitted with a patented crown with non-return outlet
which, whilst permitting the products of combustion to escape,
prevents them blowing back into the lamp. It is fitted with a
magnetic lock and a spring ball valve, which enables filling by
an oil filling machine to be done in a few seconds. The bonnet
crown is recessed and notched in such a way that by means of a
rotatable serrated ring plate the handle may be definitely located
in one position, remaining fixed whilst the weight of the lamp is
on it. By this arrangement the lamp can be carried with the
reflector always at the back.
The "Oldham-Wheat" lamp is an improved type of spot
lamp to which is attached a small flame safety-lamp. The flame
safety-lamp, or detector lamp, is constructed along similar lines
to the Stephenson lamp of the year 1815, having a perforated
metal cylinder containing the necessary gauzes and glass. Like
the Stephenson lamp, it does not emit light, and the interior of
the lamp is finished black, so as to give no reflection inside the
lamp. By this means, the user is not confused when making a
test for gas. A small armoured-glass viewing slit gives a clear
view of the testing flame, but keeps out extraneous light. The
relighting of the detector is carried out by means of a special key,
which is inserted and rotated, and therefore the detector cannot
be accidentally lighted.
The "Ceag" type is the well-known inspection lamp with the
addition of a flame testing lamp, provided with an internal igniter.
The relighter oil lamp is constructed entirely for the purpose (if
testing for gas, adequate protection being assured by means of
a double gauze. A single button, placed conveniently at the side
of the lamp, controls both the height of the flame and the relighter
action. Recent improvements to this type of detector are,
increased air space for the flame, and the flame made more easily
visible. The oil vessel has also been enlarged, making it possible
for the flame to burn continuously throughout a full shift.
Automatic Gas Detectors.
Although automatic electric gas detectors arc beyond the scope
of this paper, they will no doubt be of interest to the mining
student in view of the recent regulations, making the use of
automatic detectors compulsory in certain cases.
This type of detector has been developed by International Gas
Detectors Ltd., who have two on the market, viz. the Ringrose
Automatic Firedamp Alarm and the Ringrose Miners' Lamp,
Type CH4. The first-named is purely a gas detector, while the
latter, as its name implies, is a combination of a miner's lamp
and an automatic gas detecting device.
The principle of the gas detector is in both cases the same.
They depend for their action on the fact that if inflammable gas,
inside a porous pot, is burnt by a hot filament, there is a reduced
pressure or a partial vacuum produced in the pot and also that
the partial vacuum formed is a measure of the percentage of gas
present in the atmosphere inside the pot. This partial vacuum
is communicated to a collapsible diaphragm which is depressed
and its movement is in turn transmitted to an electrical contact,
thereby breaking an electric circuit, which in the case of the
Automatic Firedamp Alarm lights up a red bulb amid in the case
of the Lamp Type CH4, the light bulb is dimmed. Both detectors
are set to act when certain definite percentages of gas are present,
this being obtained by the suitable adjustment of the electrical
contacts.
Referring to the Ringrose Firedamp Alarm, it has some
resemblance to the standard electric safety-lamp and also that
the porous pot, which is protected by a wire gauze, is situated
between the battery and the two bulbs (white and red). Normally
the white bulb is illuminated, but in the presence of gas, sufficient
to cause the alarm to act, the white bulb is extinguished and the
red bulb illuminated.
It might be noted that the alarm does not allow of the estimation
of percentages of gas other than that for which it is set, but it has
a definite usefulness in indicating certain percentages which are
considered dangerous under certain conditions, e.g., it may be
set to indicate 1¼ per cent. of gas, the percentage at which the
electric power current must be cut off, and also 2½ per cent., at
which percentage, if the general body of the air in the working
places, men must be withdrawn.
The Ringrose Type CH4 lamp combines a standard electric
lamp and a gas detector. It is supplied with two batteries, one
of 20 and the other of 10 ampere-hours capacity, the larger battery
being necessary to supply current to the filament in the porous
pot continuously while the lamp is burning.
When the diaphragm contracts sufficiently due to the formation
of the necessary partial vacuum in the porous pot, the lower contact
is withdrawn, thereby breaking the main circuit through the
bulb. The supply of current then passes through the resistance
prior to reaching the bulb, which is in consequence dimmed by
an amount proportional to the value of the resistance. The
light remains in this condition so long as gas is present in sufficient
quantity to keep the diaphragm depressed to such a degree that
the contacts are separated.
As with the "Alarm," the lamp can be set to show any percentage.
Used in the stall, it would generally be set to indicate
2½ per cent., but of course it could be set to show 1¼ per cent.
if such was required. The positive action of dimming the light,
and also that the light remains dimmed whilst gas is present,
would appear to make it an excellent gas detector, and there
would appear to be little excuse for its warning not being observed.
The press button provides a means of short-circuiting the
resistance and of bringing the full voltage and therefore full
illumination to the bulb. This allows of the miner having full
illumination while withdrawing to a place of safety. As the
button is on the top of the lamp, the two operations of carrying
the lamp and pressing the button can easily be performed
simultaneously with one hand. Since the button must be held
in position it is obvious that the miner cannot work with a good
light in the presence of gas.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Ackroyd, — | | | |
| Ashworth, — | | | |
| Barton, — | | | |
| Best, — | | | |
| Gripton, E. H. | | | |
| Kaye, — | | | |