Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

1st June 1940, Page: 372, Column: 1

Mechanical Gumming

By H. Robinson.

From paper presented at the May meeting of the Associates and Students' Section of the North of England Institute of Mining and Mechanical Engineers.

At the present time longwall cutting machines are capable of cutting at speeds up to 42" per minute and, with an undercut of 5" holed to a depth of 4' 6", approximately 540 lb. of kirvings are produced per minute. Gummings are scattered far and wide, hut the majority are entrained in the chain as it passes round the driving sprocket, and they are carried back and deposited in the cut. To prevent this, at least two men are necessary behind the cutter, one man keeping the sprocket clean and setting sprags, while the other sets roof supports and cleans out the gummings from the cut — both these operations being very strenuous. Most convergence at the face occurs as, or just after, the cutter passes, so that working behind the cutter in front of newly cut coal is dangerous, especially when visibility is poor and respiration is more difficult due to air-borne dust. All these factors are not in keeping with the high cutting speeds and general efficiencies of modern coal-cutting machines, and to remedy this extensive experiments have been made in order to provide some automatic cut cleaning device.

Types of Gummer.

Most of the gumming gearheads which have been produced due to these experiments are capable of being fitted to the standard motor and feed sections of the various types of cutting machines, and in general they fall into two classes (i) The spiral type such as the M. and C. spiral gummer, and (ii) The paddle type, of which the Austin Hoy gum loader is a good example.

The M. and C. spiral gummer consists of a neat and robust spiral conveyor which is hinged so that the kirvings brought out by the cutting side of the chain are conveniently deflected into the spiral by means of a deflection plate. The gummer is operated by gearing from the large wheel in the gearhead, a small pinion wheel engaging with this bevel wheel and through bevel gearing operating either of two dog clutches, this being the whole of the permanent attachment to the cutter. The particular dog clutch engaged depends on the direction of cutting. The actual gummer is very quickly fitted to this permanent attachment, according to the makers a time of two minutes being sufficient. By tightening a single capstan headed nut a spring loaded dog clutch on the gummer engages with the driving dog clutch already mentioned and the spiral is operated through a chain of four gear wheels. The cylinder, within which the spiral rotates, has two large diametrically opposite apertures, one of which is blanked off by a cover plate, the other being the hole through which the deflection plate guides the gummings into the spiral. These are reversed when the direction of cutting is reversed. When jibbing in or flitting the gummer can be lifted up, but when cutting this hinge movement is restrained by an adjustable tie bolt. The complete gummer increases the overall length of the cutter by about 12 inches, but with a 15" machine there is no increase in overall height or width. The kirvings can either be discharged to the side or to the rear of the cutter, and generally speaking with very close timbering or when cutting in dirt it is advisable to use end discharge, but the conveyor practice must also be considered and side discharge gummers are applicable where the face is cut before the conveyor is moved up.

The Austin Hoy gum loading gearhead is the first to combine gum removal and conveying. There is a centrifugal disc gum-collector which is a circular plate of high carbon steel, keyed to the main shaft and revolving in a groove in the bottom plate at the same speed and direction as the sprocket. Actually only about 10 to 15 per cent. of the kirvings are not chain swept, about 80 to 90 per cent. of the kirvings being entrained in the chain and swept out of the cut, where they are picked up on the disc and immediately formed into a gum rim due to the centrifugal action of the revolving plate. Since the goaf side of the disc is completely covered in by a circular baffle-plate the kirvings are carried round until picked up by the rubber-topped deflector or plough, and forced into the radial vanes of the rotary shovel.

The elevator is driven through an overload slipping clutch of from 2 to 4 H.P. by a train of epicyclic gearing from the main shaft at a speed of thirty-six revolutions per minute and a secondary drive of light bevel-gearing operates the detachable and extensible conveyor.

As the kirvings are deflected from the gum-collector they are picked up by the vanes of the rotary shovel where they are elevated, and at the top, since the rotary shovel is inclined forward, the kirvings drop vertically under gravity on to two apron-plates which guide them to the belt conveyor.

The conveyor drive is through light bevel-gearing, but the final transmission is through a dog clutch on a swivel joint, thus enabling the conveyor to be swung from a position at right angles to the machine to a position in line with it. The conveyor can be made extensible, and it can he raised or lowered while delivering, so that no difficulty is experienced in discharging dirt into the goaf or coal kirvings on to the face conveyor or behind the machine. The belt is 8 inches wide and the length is chosen to suit the timbering system, the conveyor practice, and the nature of the gummings. Longer conveyors feed better into the goaf or on to the belt, but shorter conveyors are handier for swinging round props. The inclination of the conveyor is maintained by an iron chain fastened to the cutter by means of a soft iron hook, which straightens out in the event of a fall on the cutter, or when the timbering is too tight for the conveyor to swing round.

The machine has an overall length of 12' 4", and, while jibbing in and cutting out, the elevator must be removed, giving a length of 10' 4". The unit can be assembled in about fifteen minutes in moderately good conditions and the elevator can be removed in less than five minutes. The gum loading gearhand is designed to handle up to 6 cwt. of coal or 12 cwt. of dirt gummings per minute on a 2 H.P. drive, and under normal conditions can remove up to 907 per cent. of the gummings.

Efficiency Factors.

In general the efficiency of a gummer depends on several important points, of which perhaps the following are the most important. The cutting speed must first be taken into consideration, and in this respect better tests have been recorded where the machine was cutting at speeds of 28 to 84 inches per minute. When cutting at speeds of 36 inches per minute or more the general impression is that the gummer is doing too much and the efficiency of the machine drops accordingly. Sharp picks will also entrain more gummings than blunt picks, and therefore the efficiency of a gummer falls as the machine proceeds. It has also been found that the influence of gradient and cleat on the performance of a gummer is considerable. It is obvious that in working to the rise the gummings will tend to flow out, but to the dip the gummings will tend to be consolidated at the back of the cut. In the latter case false breaks may become induced in the coal, with the result that "breaker" coal becomes common and this is detrimental to the efficient use of gummers. The position of the holing is also important when considering the efficiency of a gummer.

In overcutting or when holing more than 8" to 12" from the floor of the seam, depending on the thickness of kerf, no gummer is necessary since the chain cleans the cut effectively. When cutting in the seam below this limit, or when undercutting in the floor of the seam, gummers are again advantageous but their efficiency will be impaired when dirt gummings are being handled. It is a recognised fact that stone gummings do not flow so well as coal, and there is a greater tendency to choke the gummer.

Advantages — Including Safety.

Both types of gummers have many advantages, and perhaps the most important is the question of safety. In general it is much easier to set sprags and rigid supports at the face immediately the coal is cut, thus subsidence is minimised, roof control is better, and there is less likelihood of falls of roof at the face. The advantages of a clean face to the coal filler are also obvious. A gumming gearhead is also a perfect pick guard and the cutting chain is almost totally enclosed, so there is little danger of failing on to the revolving picks. Admittedly pick changing is a slightly longer operation, but the total enclosure of the chain does not add to the frequency of the chain sticking since a momentary reversal releases any obstruction in the holing. Respiration is also much easier and visibility much better when gumming, due to the quantity of dust in the atmosphere being less, and the dust which is formed mainly breathes from the mouth of the cut,

The results of a kirvings test showed that without a gummer 59.0 per cent. of the kirvings were +1/8 inch and 2.5 per cent, were -200 B.S.S., while with the Austin Roy gummer 80.9 per cent. were + inch and 0.8 per cent. were -200 B.S.S. Therefore, in general, with the pick sequence and cutting speed unaltered, the use of a gummer will increase the size of the kirvings, and the percentage of -200 B.S.S. kirvings which is responsible for the air borne dust is considerably decreased.

Without a gummer it is impossible to prevent gummings being carried back into the holing, and the resultant churning and grinding puts considerably more wear and tear on the machine than is necessary. Gummers immediately remedy this, with a saving in power and longer life of cutting picks and machines. The makers are able to mention cases where a 30 per cent. saving in power has been effected, and personally I am able to quote tests giving a 30 per cent. saving in picks.

Test Results.

Mechanical gumming prevents the gummings being packed at the hack of the holing so that the effects of shot-firing are more widespread, there is less shattering of the coal around the shot-hole, and the coal splits more readily along its jointings to give larger coals. In a test lasting 15 weeks the cost of explosives per ton was reduced from 1.01d. per ton without mechanical gumming to 0.96d. per ton with mechanical gumming, and the output was increased from 9.35 to 11.75 tons per manshift. When the gummings are tightly packed at the back of the holing the coal is much more difficult to work, false roof breaks are formed, and there is a greater danger due to falls of coal and roof at the face; these are eliminated by using an efficient gummer.

Run-of-mine tests have shown that mechanical gumming increases the size of the coals produced, and the average + 4" over a test of seven weeks with hand gumming was 29.5 per cent., which increased to 37.9 per cent. on the introduction of mechanical gumming. The percentage of top stone and band, however, decreased from 2.9 to 1.9 per cent. over the same period, and this supports the statement with respect to mechanical gumming giving better roof support and fewer falls.

In thin seams mechanical gumming can be applied very successfully, and in addition there will be a decrease in labour costs due to the removal of at least one man per cutter, and in wet conditions gummers have been tried and have given excellent results.

Finally, although it does not affect the north-east so much as other parts, there is the important question of the emission of gas from the undercut. By using mechanical gummers a holing of less width can be made and less gas will be given off from the coal, but against this there is the fact that the smaller holing may allow of less ventilation entering the undercut to dilute the gas which is formed. Personally I am of the opinion that a smaller holing kept clear of kirvings at the mouth by means of mechanical gumming will admit more air to the undercut than a larger holing obstructed at the mouth by heaps of hand-shovelled gummings.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Robinson, H.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print