20th April 1940, Page: 325, Column: 1
The Mechanism Of Wear
By T. U. Matthew.
Extracts from paper read by Mr. Matthew before the South
African Institution of Engineers and published in the JOURNAL of
the institution.
Metallic wear is a fundamental problem in every branch of
mechanical engineering for the simple reason that a wear condition
exists wherever two surfaces move in contact with each other.
In mining, for example, hundreds of tons of metal in the shape
of rock-drills, jack-hammers, scrapers, ore mill balls and liner
plates are being worn away against rock surfaces each year, and
a rough estimate indicates that the cost of wear, including the
labour costs entailed in drill sharpening, mill liner replacements,
etc., on the Witwatersrand alone, exceeds £5,000,000 per annum.
Wear is thus responsible for nearly 10 per cent. of the overall
costs in mining, that is, nearly 2s. per ton of ore milled on the
Witwatersrand gold mines.
Another aspect of frictional wear is the power which must be
expended to overcome frictional resistance, and the fact that this
power is largely converted into heat.
Thus if W is the contact pressure in lb. ; u the coefficient of
friction and v the sliding speed in feet per minute —
The heat units generated =
B.Th.U's per minute.
Undesired wear takes place in two stages; (1) During "running-in"
when a polished, and in most cases, work-hardened skin is
formed on the metals, and (2) after this stage is reached, when a
gradual process of frictional wear takes place on the polished
surfaces. With these ideas as a background, the definition must,
therefore, he expressed somewhat as follows: "Metallic wear
is any undesired removal of metal due to the action of frictional
forces."
Metallic Contact.
Wear can only take place when actual metallic contact is
established between two sliding metal surfaces. Thus lubrication
by means of a film of oil eliminates wear because the oil film
effectively prohibits direct metallic contact.
Friction between surfaces separated by a viscous film is reduced
to a very small value, which is a direct function of the viscosity
of the oil.
Where the oil film is reduced in thickness until only an adsorbed
layer of a few molecules thick remains, however, the close molecular
attachment between the oil and metal greatly affects the friction,
which now becomes a function partly of the characteristics of
the bearing metal and partly of the oiliness of the oil. This is
the condition known as "boundary lubrication."
Finally, where chemically clean, dry metal surfaces are in
actual contact, the friction force is entirely dependent upon the
nature of the metal surfaces, and reaches a high value.
Summary of Results.
The most important results obtained from research on the
mechanism of wear are as follows :—
1. Initial wear during the running-in of surfaces is dependent
upon the type and degree of surface roughness left by the
machining operation.
2. Polished or run-in surfaces have an amorphous layer
formed gradually from metal particles.
3. Oxide films exist in all surfaces and influence wear considerably.
4. Oxidation wear occurs in cases where the oxide film is
continually being removed by the movements of contacting
surfaces, even with lubrication.
5. Sliding contact temperatures under high point loads and
speeds may be as high as the melting point temperature of the
metal. With steels, temperatures above l,000°C. have been
measured even when lubricated.
6. Seizing takes place readily between absolutely clean
surfaces at normal temperatures, although high temperatures
cause plasticity of the contacting points, and thus assist seizing
on contaminated surfaces.
7. As two surfaces move together in contact, friction is caused
by a continual seize-shear action at the points of contact.
8. Seize-shear is associated with the metal slip-planes and
does not occur regularly on graphited surfaces where the slip-
planes are parallel to the surface.
9. Seizure does not take place on compressed fibre surfaces
owing to the self-lubricating nature of the surface. Nevertheless,
such surfaces wear steel rapidly by oxidation wear and polishing
action.
Similarly, the most important general results obtained from
service wear tests are as follows :—
10. Hardness is not a reliable index of wear resisting properties.
11. Metallic wear is proportional to bearing pressure and
sliding speed.
12. The type of lubricant used greatly affects wear.
13. Wear is greatly influenced by oxidation.
14. Wear is greatly influenced by humidity.
15. Wear resistance is a function of the coefficient of friction.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Matthew, T. U. | | | |