Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

20th April 1940, Page: 323, Column: 2

Advantages Of Turbine Pump

In his paper on Turbine Pumps in the ANNUAL MAGAZINE of the Notts. Mining Students' Association Mr. D. Harper lists the advantages of the turbine as follows :—

(1) The turbine pump because of its simple design is comparatively cheap.

(2) The cost of installation is smaller because the small overall dimensions reduce the amount of excavation necessary.

(3) The load can be applied gradually by use of the gate valve.

(4) The frictional resistance is small.

(5) There are only two glands in a turbine pump and so the resistance due to this cause is minimised. The packing glands require little attention except for an occasional tightening of the gland nuts, and renewal is only necessary every three months.

(6) The turbine pump is probably the most efficient type of pump, a good overall efficiency being in the region of 70 per cent. This is largely due to the fact that the pump is usually driven direct.

(7) Maintenance of turbine pumps is easy, and they can be readily converted to deliver against varying heads.

(8) They are also reliable, and cases of pumps running continuously for years without any serious reduction in efficiency are common.

Points that should be observed when centrifugal pumps are put into service are stated thus :—

(1) In order to avoid unnecessary friction and development of heat, the packing should not ho pressed too tightly by the gland; a little water should drip out continuously.

(2) The oil wells of ring lubricated hearings should be carefully cleaned and filled to the correct level with the appropriate oil.

(3) The pump is primed by opening the air cock, and by-passing water past the non-return valve. The pump is primed when water appears at the air cocks, which are then closed.

(4) When the pump has been primed the by-pass should he left open whilst starting the pump. After the pump has started delivering water the by-pass valve should be closed.

(5) When a pump has been out of service for some time it should be rotated by hand to ensure that it runs easily, and care must be taken never to run a centrifugal pump without water in it.

(6) The pump should be started with the gate valve closed and the gauges carefully watched. The pressure should rise steadily as the speed increases, and if it does not do so, it may be assumed that there is air in the pump and priming must be carefully repeated. The pump is then run up to full speed and the gate valve slowly opened until normal working conditions are reached. Should the ammeter show that the motor is fully loaded before the full delivery is obtained, the motor should be shut off or overheating may occur.

(7) The valve in the by-pass pipe is closed when normal working conditions are reached. The object of keeping the by-pass valve open during starting is to permit a small quantity of water to circulate, thereby preventing heating of the pump.

(8) To stop a pump the regulating valve must first be closed before tripping the switch.

(9) Should the speed of the pump fall so that delivery ceases, the plant should be shut down until normal speeds may be obtained.

The following points should also be observed: (e) Whilst the pump is running, regular observations of the pump gauge should he made. (b) The packing material should always be in good condition, so that the air seal is maintained. It should be renewed when necessary and the gland nuts tightened occasionally. (c) The valves and strainer must be kept clean. (d) When the pump is out of commission the internal parts must be protected from rust, and all water must be drawn from the pipes and pump in frosty weather.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Harper, D.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print