27th January 1940, Page: 229, Column: 2
The Sylvester Prop
A summary of the paper on Steel Roof Supports at the Working
Face, by Mr. J. F. Carr before the Manchester Geological and
Mining Society, is given in preceding columns. In an appendix
to his paper Mr. Carr offers some particulars of the Sylvester Prop
as follows :—
This prop is a further invention of the man, who, more than
forty years ago, gave to the mining industry the pulling device
known as the sylvester. The prop is almost as great a contribution
to safety as the pulling device, as it entirely eliminates the
necessity for a person to go near a prop for the dangerous process
of loosening the head or foot before withdrawal. By its use such
natural conditions are overcome as those quoted in a recent report
of the Safety in Mines Research Committee to the North Staffordshire
Institute of Mining Engineers on the Use of Steel Props at
the Face, wherein it is stated that "A natural condition for which
wedge props are not suited has been observed; this is where the
roof settles down on the prop on the release of the wedge."
The sylvester prop is a wedge prop, but the wedge is only
intended for setting purposes and not for release, and the release
mechanism functions equally well when the wedge is only partly
driven up. There are three well-designed features of the prop
(a) the wedge; (b) the release mechanism; (c) the arrangement
for locking. The means for locking and releasing are a considerable
step forward, as the parts in contact have a rolling action
on each other, thereby reducing friction to such an extent that
withdrawal is simple.
The upper end of the prop body is cut at a suitable angle and
so is the underside of the head, and on release the action of the
roof load imparts an outward thrust to the prop body. The headpiece
and the body of the prop are locked together when the prop
is set by means of a lever with its upper short beak-shaped end
projecting into a slot in the base plate under the head this lever
is pivoted on the body, and the longer end is secured against
rotation by a plate which slides on and is hooked to the prop
flange. To make handling of the prop an easy job this longer
end of the lever is cranked outwardly to give a hand hold.
To withdraw the prop a chain of suitable length is used; one
end is fitted with a jaw-shaped claw lever, and this is attached
to the lower end of the locking lever. A small peg, on which there
is no load, is then withdrawn and a pull is given to the chain.
The prop is immediately released. The action of the claw is to
force down the sliding plate which covers the end of the locking
lever and thus allow it to rotate and move out of the slot in the
locking plate.
To summarise how the release is simplified : (1) The roof plays
its part by setting up the outward thrust. (2) The locking plate
and the short beak-shaped end of the locking lever have a rolling
action upon each other. (3) The handle or tail end of the locking
lever has a leverage of 6 to 1. (4) The outward thrust on the lower
part of the tail is therefore only one-sixth of that exerted on the
beak-shaped end, which thus reduces the lifting action on the
sliding plate.
When the prop is released the head falls back, leaving ample
clearance from the roof.
Buffer studs and a cross-bar welded between the prop flanges
control the movement of the head, and a lug welded to the back
of the prop serves as a protection against trapped fingers by keeping
the head a short distance away from the prop body.
The wedge has a lifting power of 6 tons with an upward movement
of 1 inch.
The fabricated head is designed to withstand a greater load than
the prop body, and there are no loose parts to go astray.
The Sylvester prop will facilitate compliance with paragraph 98
of the "Summary of Main Recommendations" by the Royal
Commission. With the other steel wedge props a long-shafted
hammer will be called an "approved safety contrivance."
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Carr, J. F. | | | |