Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

27th January 1940, Page: 228, Column: 1

Introduction Of Steel Supports

At the meeting on 16th January of the Manchester Geological and Mining Society Mr. J. F. Carr presented a paper with many illustrations on "The Introduction and Use of Steel Roof Supports at the Working Face." He opened by quoting from the Report of the Safety in Coal Mines Commission the statement that "There is a general consensus of opinion that where the conditions permit of it, the use of steel on the coal face facilitates systematic roof control and gives a high factor of security." Mr. Carr said that progressive mining methods necessitate intensive and systematic roof support and control which afford the highest factor of security, so that very little alteration to the statement is required for it to read "There is a general consensus of opinion that steel roof supports should be used on all intensive faces."

To attain the full advantage in the use of steel supports it is necessary to eliminate waste and to replace all timber on the face by the use of steel props and bars. There is no doubt that the introduction of steel supports, particularly at the working face, has been a very important feature accompanying the progress in methods of coal mining. It is essential for safety and economic operation and can be applied under most conditions in mechanised mining methods. At the present time there is in addition the restriction of supplies of imported pit wood.

The object of Mr. Carr's paper was to give a practical account of a recent change from timber to steel supports at the face. The introduction of steel supports has been effected on four faces — two strike faces in a Four-foot seam; one strike and one dip face in a Six-foot seam.

The Four-foot Seam.

The two strike faces in the Four-foot seam were in the first instance changed over to steel. The faces were advancing in opposite directions and were cut and cleared on a 24-hour cycle. The thickness of cover was 3,500 feet, the gradient 1 in 3½. No. 1 Face was 78 yards and No. 2 Face 190 yards in length and both were undercut to a depth of 4' 6" in the inferior coal hand at the bottom of the seam. The coal-cutters were fitted with gumming devices which had an important bearing on the effective clearing out of the holings, and the immediate use of steel sprags to support the undercut coal. The roof was a very soft irregular shale, with many potholes and fossil plants, whilst numerous joints tended to further the disintegration of the immediate roof. The floor was warrant, which lifted considerably although it had a fairly hard crust, and was generally penetrated by the props.

Giving a statement of the conditions prior to the introduction of steel Mr. Carr said it was obvious that, if steel props and bars were to be used on the faces, consideration must be given to reduce the period between the setting and the withdrawal of the props; it was therefore decided to experiment with various methods of packs, etc., to reduce the convergence on the face under the most difficult conditions pending the delivery of the steel supports.

Attention was given to the quality and spacing of the packs, and in addition rows of hardwood chocks were introduced opposite the wastes. During the filling shift two rows of chocks were used, one on either side of the conveyor, and as the cut was cleared a third row was set in the new line of timber, so that when the machine was cutting there were three rows of chocks and the conveyor was advanced to the position between the two front rows. During the next shift the back row of chocks was withdrawn, to be re-set in the new row of timber. The chocks were set on the firm floor and bricks were used to facilitate withdrawal. The width of the packs and wastes was varied several times, and the packs advanced before coal-cutting. Following each alteration to the packing system convergence tests were made during the three cuts.

The roof in the wastes fell to a greater height and more regularly in the fourth test, and from the experience it was accepted that the chocks had justified their use. A tendency for the roof to weight coincided with the second test. There were signs of improvement in the roof due to the chocks; the rearranged packing and the fact that the props were withdrawn after three instead of four cuts as previously, all of which, no doubt, effected a reduced convergence. The progress, however, did not fulfil expectations.

The Author then dealt with the introduction of steel, when the previous arrangement of packs was unaltered but the use of chocks was discontinued, The face was equipped with rigid tubular props. He pointed out that the great disadvantage with the rigid tubular props is their withdrawal. It was found practically impossible to withdraw them in a direction at right angles to the face, although this difficulty was overcome by the use of two sylvesters pulling simultaneously the prop and channel bodily to the rise. This withdrawal was difficult and costly, creating a decided tendency to drag the soft roof, causing local falls from the edge of the waste on to the conveyor.

A short trial was arranged with wedge props, after which a number of the sylvester easy withdrawal props were introduced for trial, and installed opposite a waste. Easy release and withdrawal were obtained with this type of prop from the start; the collapse of the head provided a clearance of 3 to 4 inches between the top of the prop and the underside of the channel, even after movement had taken place and the immediate roof had "followed." This enabled a normal sequence of withdrawal in the following order, a back prop first, then the front prop, with a chain attached to the channel for pulling it out either by hand or, in the case of it being buried, by a sylvester. Moreover, the need for setting timber for protection was no longer required. The two strike faces were then fully equipped with this type of prop, and no further trouble in the withdrawal has been experienced ; the roof conditions at the faces improved and breakaways from the waste edge — due to pulling props and channels out simultaneously — did not arise.

The Six-foot Seam.

After the Four-foot seam had been fully equipped the change to steel was arranged for the Six-foot seam. The conditions on the dip face were that the roof was stronger, hut the floor was very soft and did not offer sufficient resistance to the penetration by the props. Moreover, the face advanced slightly across measures dipping at 1 in 3. On the strike face the section of coal was not as thick as on the dip face, and the roof and floor were both fairly good, but the inclination was 1 in 2.4. It was realised that the handling and setting of a steel bar together with a 5' 9" steel prop, top-heavy due to the wedge headpiece, was a matter of considerable difficulty on this gradient and farther, the floor was inclined to be slippery, with the danger that accidents would arise if props were knocked out, or fell whilst being set.

The face was therefore set out fully mechanised on a 24-hour cycle, equipped with 5' 9" wedge props and 4' 6" corrugated bars. Corrugated bars were selected as they are lighter to handle when set under these conditions, and in order to keep the setting under proper control instructions were given that this work was to be done by three men. Each man to obtain the help of higher and lower side neighbour when about to set a bar; in addition a floor barricade was erected against the higher side of it when completed.

Hardwood chocks together with chock releases were also used, and a waste pack was built between the two roadside packs. The roof broke down regularly, and in small pieces from the commencement, so much so that, in order to obtain efficient packs, bag packing was introduced. Very little difficulty was experienced on this face, and the only change made was in substituting channels for the corrugated bars, which in addition tended to steady and maintain the props in position whilst being set.

Checking System.

The checking system adopted requires that every steel prop on a face is marked with a letter and a number, and that each prop be erected in the correct relative position on the face. The letters and numbers are painted on the web of the prop in black against a white background. The numbers denote the row of props at right angles to the face, and the letters the row of props parallel to the face.

When a prop is missing its number is known, and that number is an indication where to look for it; if a prop is damaged the replacement prop is marked with the same latter and number as the damaged one. By this means a continuous cheek is kept by the fireman in charge of the face, and recorded in a book. Every month the props in each section are checked by a senior official, and quarterly a complete inventory is taken, surface and underground, from which all losses are computed.

The advantages of steel on the coal face are permanency and the elimination of the daily trouble and expense of transporting and handling large quantities of timber underground ; this is particularly costly and inconvenient where the measures are highly inclined. On the other band, steel props and bars may be uneconomical if losses are high, but with efficient organisation and a proper system of checking losses can be controlled. More steel props are lost through being laid on the floor and buried, than by leaving them undrawn in the wastes.

In the statement of his conclusions Mr. Carr stated that on all faces it was found necessary to accommodate the height reduction or convergence which took place whilst the props were set, by inserting a wood pad to act as a compression piece.

The steel resulted in a marked decrease in face support cost.

The use of steel on the faces for nearly all purposes, such as props, bars, cutter sprags, etc., makes the absence of timber very much felt, as there is no broken timber available for such purposes as backing behind the arches, or building it in packs to help to stabilise the walls (very often done in steep measures), etc. In such cases corrugated steel is used behind the arches on the main roadways, and deal timber is sent for hacking in other roads. Bags filled with dirt are used in the pack walls where required.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Carr, J. F.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print