2nd December 1939, Page: 162, Column: 1
Modern Coal Mining Methods
By Thomas Bryson, A.R.T.C., M.I.Min.E.
From paper presented at the November meeting of the Preston
Scientific Society. Mr. Bryson is Head of Mining Department at the
Wigan Mining and Technical College.
Large Capital Sums Involved.
Coal mining is an industry of great antiquity. It may have
been known to the Roman invaders of Britain, although there is
no authentic record of coal having been mined in this country
before the end of the twelfth century. It is safe to assume that
even then it was obtained from workings limited to outcrops
above the drainage level of the districts in which those early mines
were situated. Attempts to obtain coal at lower levels in early
days were frequently frustrated by the influx of water in such
quantities as to drown dip workings. It was largely due to the
ingenuity of Watt that the problem of dewatering mines was
solved. This constituted a notable phase of the industrial
revolution. The entrance to a coal mine in those days, it may
be noted in passing on to the main subject of this lecture, was of
the simplest possible kind. It had no resemblance to the entrance
to a modern mine.
Some of the shafts of to-day have been sunk to a depth of
1,000 yards and fitted to enable thousands of tons of coal to be
raised each full working day. The sinking of such shafts is a
hazardous adventure and the provision of the machinery and
other equipment required to drive coal-cutters, conveyors, pumps,
fans, winding engines, haulage engines and coal-cleaning plant,
involves the expenditure of large capital sums. To raise an
output of half-a-million tons of coal per annum might involve
in the sinking of shafts, provision of the machinery, etc., the
investment of £500,000. Such large capital sums are provided
by industrialists who are prepared to take the risk of operating
a concern whose assets are progressively wasting. Because of
the wastage of assets shareholders naturally require the repayment
of the capital sums during the lifetime of the colliery in
addition to a margin of profit amounting to a reasonable measure
of the risk taken. Profit is an essential inducement of industry.
Machines Performing Laborious Work.
There are two general methods employed to extract coal seams
in this country — longwall and pillar and stall. In the former
case the face of the working is usually composed of a number of
steps, or short walls, about 15 yards long, where hand working
is practised, but where mechanical methods are employed the
face may be hundreds of yards long and in one straight line.
Hand holing is a laborious job and is not an efficient method of
getting coal, and because of that mining engineers have long
been engaged in the design and development of coal-cutting
machines suitable for performing the operations formerly performed
by miners.
The "bar" was one of the first efficient machines to be used
for undercutting the coal, and later the "disc" machine was
applied to the same operation when harder coal had to be cut.
Now, the chain machine, driven electrically or by compressed air,
is generally used for holing the coal at almost any position from
the level of the floor to the roof.
Formerly coal-cutting machines were mounted on wheels
running on rails, but now they are run on skids sliding over the
floor, or they are fitted with crawlers by which their mobility
is increased. As the machine travels along the face, the debris
produced is shovelled out from under the overhanging coal by
an attendant, and to prevent the attendant from being injured
by contact with the picks attached to the chain a guard is fixed
to the rear end of the machine. Gummers are now being fitted
to deliver the debris near to the conveyors.
Electrical v. Compressed Air Machines.
When coal seams are of medium thickness, from four to eight
feet, the pillar and stall method of working is employed. Stalls
about four yards wide are driven in the seam to form pillars of
rectangular shape with sides 30 or 40 yards long, and when
several ranges of pillars have been formed their removal is
commenced and the roof is allowed to collapse in the goaf. In
driving the stalls the coal may be undercut by hand, or percussive
coal-cutters may be used for that purpose. Compressed air is
quite commonly used where much firedamp is given off, but if
the gas hazard is not too great the greatest efficiency is obtained
by transmitting power electrically to the compressor situated
near the coal-cutter at the face.
One side of the stalls may be cut out by a shearing machine
driven by electricity, or a compressed air machine may be used
to perform that operation. When undercutting and shearing
have been done the breaking down of the coal is simplified, and
it may be unnecessary to have recourse to blasting.
Where coal is liable to spontaneous combustion it may be
removed in panels which can be isolated in the event of a fire
breaking out.
After the coal in the seam has been undercut it may be broken
down by picks, wedges, multiple wedges, air picks, or explosives,
or a substitute for blasting may be used.
Use of Supports.
The most prolific cause of accidents in collieries is the collapse
of the roof and sides of roadways and other excavations, and
to prevent such accidents supports of various kinds are used.
In modern mines timber for this purpose has to a large extent
given place to steel ; some collieries even use steel supports
almost exclusively.
On the working faces steel props and bars are used, the props
being rigid, semi-rigid, or collapsible. Where the distance between
the roadways leading to the coal face is great rows of stacks or
chocks are used to form a good support, but the greatest reliance
is placed on packs built with the debris obtained from ripping
down the roof in the roadways to obtain the required height for
setting up roadway supports. The latter may consist of props and
bars, or they may consist of curved steel girders set up on side
bars supported on props. By far the most effective form of
support is the steel arched girder now so widely used in the modern
collieries of this country.
Prevention of Subsidence.
In some of the British coalfields subsidence of the surface has
been prevented by filling the space from which coal was extracted
with the debris of the mine, the dirt being flushed into position
by water fed into a pipe line extending from the surface to the
working places. It is said that the subsidence that actually
occurs is limited to about one-twentieth of the thickness of the
seams worked out. That would admit of coal being extracted
from built-up areas without damage to property on the surface.
The introduction of water, which must be pumped out again,
may be objectionable on account of its deleterious effect on the
strata in which roadways are formed. That difficulty may be
surmounted by carrying the packing material into position by
means of compressed air. Mine refuse is carried by conveyors
into the hopper of a monitor from which it is ejected by means of
a stream of compressed air to fill part or whole of the space
formerly occupied by the coal seams. The practice of the
hydraulic method of packing has led, in the counties of Fife and
Lanark, to safer working conditions, less risk of underground
fires, and reduction in the cost of mining. Still, the hydraulic
and pneumatic methods of packing have not been widely
practised.
Underground Transport.
When coal has been dislodged from its natural bed and the
collier has seen to the proper support of the roof in his working
place, the work of filling the coal is begun. In the days when
mining methods were primitive coal was filled into small tubs
and these were taken to the shaft by putters. Ponies were taken
underground to haul sets of tubs along the underground roadways,
and there are over 30,000 of them presently employed in British
mines. The number is gradually diminishing and it may be
expected to continue to diminish as the value of mechanical
transport is appreciated.
The force of gravity is taken advantage of in order that trains
of loaded tubs running downhill from the face of the workings
may haul up towards the face trains of empty tubs, but when the
workings of the mine lie towards the dip of the shafts it becomes
necessary to employ mechanical haulage of some kind. In
mechanical haulage a steel rope is used to haul the tubs in trains
from the far end towards the shafts, and of the systems of haulage
generally employed the endless rope is by far the best. It moves
slowly but continually, and consequently much coal can be
transported over great distances with economy and safety.
On main roadways of suitable gradient electric locomotives of
the storage-battery type may be used to haul large outputs of
coal over moderate distances with efficiency and safety, and we
may expect that in the near future more locomotives of the
Diesel type will be used in main levels.
Compressed air locomotives are common in continental mines.
So far as we in this country are concerned it may be said that for
the present we find it advantageous to haul coal over great
distances and in large quantities by means of endless rubber belts,
which convey the coal from the face of the workings to the main
road where it is delivered to another gate conveyor which may
transport it for a distance of 1,200 yards or more to the shaft
siding. There it is usually filled into tubs amid clouds of fine
coal dust unless steps are taken to collect the dust at the loading
points.
A series of belts may be installed, one feeding the other until
the shaft is reached. As the loading point is reached the conveyor
is gradually raised to a sufficient height to enable the coal to fall
from the conveyor into the tubs by which the coal is taken to the
screening plant on the surface. The endless rope haulage by which
loaded tubs are taken to the shaft may run under the tubs or
above them, the former method being characteristic of Scottish
mining practice, the latter of English and Welsh practice.
At Bickershaw Collieries the tubs arrive at the shaft and are
directed into mechanical tipplers by which they are overturned
to discharge the coal into huge bins below the level of the roadway.
Coal is fed from the bins into skips carrying 8 tons, and when the
skips reach the surface they are discharged to the screens. This
new plant which has been installed by the Metropolitan-Vickers
Electrical Co., Ltd., may be made to operate quite automatically
to raise 440 tons per hour from a depth of 780 yards
Explosions Problem.
Allusion has already been made to the clouds of fine coal dust
produced at conveyor delivery points. These clouds may be so
dense that a lighted lamp cannot be seen at arms length and in
which one can hardly breathe, but by the ingenuity of the agent
and manager of Ince Moss Collieries these clouds need no longer
exist. A fan forming part of a dust collector dedusts the coal
as it falls from the conveyor into the tub and the dust meets a
whirling spray of compressed air and water which at once produces
a fine slurry that is collected and taken out of the mine. Loading
points may now be quite free from fine coal dust.
Our S.M.R.B. experts are concerned with the determination
of the best means of preventing explosions, and it is no fault of the
Board that we have still to chronicle the occurrence of catastrophies.
Coal dust can be rendered innocuous by treatment with water
in the form of a fine spray and by admixture with stone dust
which has been produced by the grinding of shale, limestone,
fuller's earth or gypsum, and in a mine that is not naturally
wet throughout it is required that roadways should be strewn
periodically with inert dust and that shot-firers should spread
stone dust in the regions in which shots are to be fired. Every
effort is made by the Mines Department, colliery officials, and
educational authorities in mining districts to bring the danger of
explosions to the workers. That good wurk will continue in the
hope that the risk of explosion may be eliminated from the list
of mining dangers.
Value of Ventilation.
When it is realised that for every ton of coal got out of a colliery
it may require 5 tons of air to be circulated throughout the
workings per minute the importance of mine ventilation will be
readily understood. It is required by law that an adequate
amount of air shall be constantly circulated throughout the
workings of a mine to render harmless the noxious gases that are
given off from the strata during the extraction of coal or are
generated by the processes of oxidation, combustion, and
respiration.
Accumulations of blackdamp and firedamp may occur as a
result of failure to send the air through all airways and working
places, and carbon monoxide, the most insidious of mine gases,
may be found in the air-currents circulating through districts
in which the coal is liable to spontaneous combustion. Those
are other reasons why ventilation should be plentiful and properly
directed,
Most Lancashire collieries are ventilated by fans of the Indestructible
type. Modern development in the design of fans
tends to the construction of smaller high-speed fans, such as
the Aerex fan. The basic principle of these high speed fans was
quite well understood half-a-century ago; indeed, the Rateau
propeller fan was then in use. The rapid development of aeroplane
propeller design during and after the war of 1914-18, and
the number of such propellers that became available after that
war, led to the building in South Africa of the first of the modern
fans of that type. New installations of ventilating fans are
likely to incorporate high-speed fans because of their greater
efficiency and the enthusiasm with which responsible engineers
greet the development of engineering skill.
The Sirocco was an epoch-making fan, for although it had long
been used in small sizes aboard ship it was introduced to the
mining industry in small-medium sizes running at the medium
speed of about 250 to 350 revolutions per minute.
Such fans are built up on the surface and are connected to
the upcast shaft by an airway or drift, but the provision of a
main fan on the surface does not preclude the use of a booster
fan somewhere in the mine workings. The air is taken down one
shaft, along the main and subsidiary airways to the working
places, thence into the return airway and back to the upcast
shaft. Distinct currents must be maintained by the use of air-crossings,
stoppings, doors, and brattice. Sometimes, as in driving
tunnels from one seam to another, portable ventilators, driven
by electricity or compressed air, are installed for the purpose of
sending a brisk current of air into the face of the tunnels to dilute
and carry away the gases resulting from the use of explosives.
It is rather important that each subsidiary current of air should
be regulated in order that each may have the amount of air
required for the maintenance of safe and healthy conditions of
employment. Mining is now often carried to such depths that
the solution of the problem of how best to maintain the body
temperature at or near the normal level becomes increasingly
difficult. Another method of dealing with the situation is to
wear scanty clothing. At the deep mines of the Rand the
problem is solved by de-humidifying the air before sending it
into the mine. The problem of the future in deep coal mining
may be solved in some such way. At a depth of 4,000 feet we
now record earth temperatures of 115°F. and air temperatures
only a few degrees lower on the scale.
Lamps and Lighting.
In guarding against the danger of explosions use is made of
some form of safety-lamp. The modern portable lamp is a great
advance on those of early mining times. Whereas the Davy lamp
gave light represented by 1/8 of a candle, modern flame lamps give
nearly 4 candle-power, some portable electric lamps give 6 candle-power,
and several electric cap lamps give a direct beam equivalent
to from 12 to 20 candle-power.
As was to be expected by advocates of the use of the electric
cap lamp cases of nystagmus have been almost entirely eliminated
from the list of persons said to be suffering from the malady.
Current for portable lamps is provided by accumulators, but
the current for fixed lamps is provided by the generating station
on the surface. Where power is transmitted to underground
machines by compressed air the generator is driven by an air motor
fitted into the lamp. In this way semi-portable lamps of high
illuminating power may be installed where machines are used in
cutting, loading, and transporting coal.
Tunnelling through hard rock is an important branch of mining
work and it is interesting from two points of view. Men engaged
in tunnelling need not depend on the light given by portable
lamps if mains lamps or floodlights are installed, and in these
days such workers are relieved of the hard labour which used to
characterise their work in former times. Tunnellers of to-day
are men possessed of engineering skill and not necessarily men of
muscle. Shot-holes are now bored by electric or. compressed air
drills set up singly or in pairs, or they may be attached in sets
of 4 to a drill carriage, such as was used in the driving of the
Hawes water tunnels and many others.
The removal of debris after blasting was formerly one of the
most laborious jobs imaginable, but with the advent of the scraper
loader it has become a simple matter to remove the debris from
a 13' x 10' tunnel advancing at the rate of 25 yards per week.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Bryson, Thomas | | Head of Mining Department | |