25th March 1939, Page: 299, Column: 1
Air Picks And Drilling Machines
In an address on Air Picks and Drilling Machines before the
Past and Present Mining Students' Association at the Wigan
Mining and Technical College, Mr. Angus Elliott said that searching
tests have proved that in soft and medium hardness of strata
a hammer drill having a short piston stroke and a resultant high
number of blows, together with a fast rotation, will drill far more
rapidly than a hammer drill fitted with a long cylinder and piston
and a comparatively slow rotation, that is of course with an
equivalent cylinder bore and weight of machine. The rapid
rotation of the drill steel is an aid to the cuttings being cleared,
and a long stroke piston strikes a very heavy blow which in turn
drives the bit too deep into the strata being bored, thus imposing
strain on the rotation, and the slow rotation does not clear the
cuttings with sufficient speed. In very hard strata a slow rotation
machine with a long piston stroke striking a very heavy blow is
required, but generally speaking the stone to be bored in coal
mines cannot be termed hard.
For boring in coal only the rotary air drill without percussive
action has advantages, though the air consumption is increased in
comparison with the hammer drill, this being due to the difference
in mechanical construction and action. The rotary hand-operated
air drill has its limitations in regard to the hardness of strata
which can be economically bored, especially as the expensive
tungsten carbide tipped drilling bits wear rapidly when boring in
abrasive strata.
Mr. Elliott expressed the view that the silicosis problem will
result in regulations for the trapping or allaying of stone dust
being enforced. This will necessitate that the dust be trapped,
or it will be necessary for hammer drills to be fitted with water
tubes which enter the shank of the drill steel, water being fed
through the steel under pressure. The first method is satisfactory
in his opinion as all operators dislike boring "wet." The dust
trap ensures "dry" drilling and the dust is deposited into a
container which is emptied when full, the dust being taken away
from the face.
The use of air picks has developed rapidly in this country in
recent years. Their advantages as regards safety are (1) Explosives
for use in coal getting are entirely eliminated in many
seams, and rippings are also "got" by air picks provided the
strata are not of excessive hardness. (2) Less shattering of roof
at the faces owing to the use of explosives being eliminated or
minimised. (3) Supports set with minimum of roof exposed.
(4) Better and safer roads owing to non-shattering of the surrounding
strata.
Other advantages claimed by Mr. Elliott for air picks are:
(a) Cleaner and larger coal produced, the value of the coal being
enhanced owing to the decrease of smalls and the ash content
being lowered through the absence of foreign matter. (b) A
regular output is maintained owing to breakdowns being practically
speaking eliminated. (c) Production of coal is increased. (d) Lower
power costs, due to low air consumption and intermittent running
of air picks. (e) Cost of explosives saved. ( f) Machine supervision
and transit costs are reduced.
Mr. Elliott said he quite appreciated that in some cases the use
of air picks alone for coal getting would not be a paying proposition,
though any coal can be won with air picks when used in
conjunction with a longwall coal-cutting machine. Before picks
are installed tests should be conducted in order to determine
the weight and type of machine for the particular conditions.
The selected air pick should enable the workman to obtain
maximum output with a minimum of fatigue.
The size of the pick will depend upon the nature of the coal and
condition of the seam. In a hard tough coal, the lecturer said a
pick weighing approximately 24 lb. and delivering a powerful
blow with a minimum number of blows per minute, would be
recommended. In soft or brittle coal a lighter pick weighing 18 lb.
to 20 lb., and delivering a large number of blows per minute,
would on actual performance prove to be more suitable than a
machine having a long stroke and powerful blow. In thin seams
the operator works on a constrained position, and here again a
light pick is recommended, as a heavy type of machine would
result in the operator becoming fatigued. For rippings an air
pick with a powerful blow and long piston stroke has been proved
to be the most suitable machine.
Proceeding, Mr. Elliott said the steel point, which when all is
said and done is the business end of the machine, should be
maintained in a sharp condition. The usual type of steel point
is tapered in order to allow rapid penetration. In soft or brittle
coal the fluted tapered point can be used to advantage, and will
penetrate more rapidly than the plain tapered point. The use
of the fluted point, however, is not advantageous in hard coal
or rippings. The fluted point has four grooves, each starting
approximately 1¼ inches up the body of the steel, the flutes or
grooves being semi-circular and inch in depth at the deepest
point.
Air pressure is an important factor, and in Mr. Elliott's opinion
a minimum of 60 lb. pressure at the face should be maintained if
possible, and better results will be obtained with 70 to 75 lb.
pressure. Air picks only work intermittently and in consequence
a large number of picks can be worked from a comparatively
small compressor and an adequate working pressure maintained.
At one colliery six air picks working from a Hardy's duplex air
compressor delivers approximately 120 cubic feet of free air per
minute. In other cases a larger number of picks have been
worked from a duplex compressor, but naturally the air pressure
dropped below 60 lb. when all the picks were working.
Cases were cited by Mr. Elliott showing increased outputs
when air picks were installed, in one of which the installation of
picks actually increased the output from 18 cwts. per collier when
winning by hand to over 2 tons per collier with air picks. A
Staffordshire colliery was instanced working the Heathen seam,
a hard coal with a strong bind roof and with 3 inches of fireclay
underlying the seam. When hand worked the product was
17 cwts. a collier. Following the installation of picks a production
of 3 tons per collier was obtained.
At the close of the address a practical demonstration was given
in the College mine machinery laboratory of the qualities of the
air pick in breaking hard sandstone from Billinge quarries and of
the electric and air drills in boring holes in the sandstone.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Elliott, Angus | | | |