|
11th March 1939, Page: 283, Column: 2 Care Of Relighter LampsIn view of it being unlikely for all orders for lamps required by the Deputies' and Shot-firers' (Safety-lamps) Order to be completed by 1st March, the date on which it was due to come into operation, H.M. Inspectors will be satisfied for the time being if mine owners can show that orders had been placed not later than that date, and that every reasonable measure had been taken to secure early delivery of the lamps. Mines Department Circular No. 121 has been circulated among mine owners, managers, and lamp manufacturers, and its purpose is to provide guidance in regard to the proper care, maintenance and operation of approved types of safety-lamps fitted with an internal relighting device, since proper attention to these points is a matter of importance in relation to the safety and efficiency of these lamps. Mr. F. H. Wynne, C.B.E., B.Sc., H.M. Chief Inspector of Mines, asks each manager to issue instruction based on the Circular to the lamp-room staff and to the officials who are to use the lamps. In the Circular he says :— The relighting device consists of a friction-wheel provided with tangentially cut teeth, against which is pressed a "Pyrophor" bar, which serves the same purpose as the "flint" of a cigarette lighter. In some mechanisms the friction-wheel is driven by means of a spring, wound up by a key and released automatically through the rotation of the key; this causes the wheel to revolve rapidly and by frictional action to produce a flash which ignites the vaporised fuel round the wick. In other mechanisms the wheel may be driven by a rack-and-pinion, of which the operating key forms a part. As a result of investigations made at the Mines Department Testing Station, Sheffield, in 1924, it was found that certain precautions are necessary in the care and maintenance of flame safety-lamps fitted with these relighting devices. Briefly these are (e) the use of an igniter bar of suitable quality ; (b) the use of a friction-wheel having fine and correctly shaped teeth; (c) the use of fuel appropriate to the lamp ; (d) the daily cleaning of the lamp, particularly the top of the spirit-vessel, and the proper adjustment of the relighter; and (e) its proper use underground. (a) Igniter Bar. — The igniter bar must be of an approved brand. The only brand so far approved is made of a ferrocerium alloy, of a superior quality to the "flints " used in cigarette lighters. Igniter bars of the approved brand are coloured green, and are supplied by the lamp makers in packets marked "With the Approval of the Board of Trade" which bear the name of the lamp in which they are to be used. These bars are made specifically for the purpose of relighter safety-lamps, and special precautions are taken in manufacture to ensure the correct consistency and ignition temperature and a compact form of flash. No other kind of igniter bar may be used in relighter safety-lamps. The alloy used for cigarette lighters, for instance, is quite unsafe for use in these lamps as its composition is inconsistent, it has a lower ignition temperature than that of the approved alloy, and the flash given consists of a shower of dispersed sparks. Unburnt particles produced during the operation of relighting with such a bar may be deposited on the hot gauzes, and may give rise to the possibility of an ignition of firedamp. (b) Friction-wheel. — The friction-wheel is provided with fine tangentially cut teeth (wheels having coarse teeth are unsuitable) and only those supplied by the lamp makers may be used for replacement. Care should be taken that the wheel is correctly assembled on its spindle, with the ends of the teeth pointing in such a direction that they cut into the igniter bar during that period of rotation of the wheel which produces a flash. (c) Fuel. — The efficiency of relighting depends largely upon the grade of spirit with which the lamp is fuelled, and no change in the grade should be made without reference to the lamp makers. (d) Daily Maintenance. — The lamp must be cleaned daily, particular attention being paid to the relighting mechanism and the top surface of the spirit vessel. The friction-wheel should be cleaned with a small stiff brush, and if the igniter bar has worn short it should be replaced. The correct pressure to be applied between the bar and the wheel is a matter of experience, but it should avoid the extremes of overtightness, in which case the friction-wheel will not rotate freely enough, and excessive lightness, in which case insufficient friction leads to a poor flash. The spirit-vessels of lamps fitted with Pyrophoric relighters are filled with an absorbent material such as sponge or cotton wool. The vessel should be completely filled and any excess spirit emptied out. The top of the spirit-vessel should be allowed to dry before the lamp is assembled, otherwise the presence of an excessive amount of vapour in the lamp may make relighting difficult. Wicks do not require trimming, provided the lamp is never allowed to burn dry. The lamp should be lighted after assembly in the lamp-room, by means of the relighter, in order to ensure that the mechanism is in proper working order before issue to the user. Care should be taken that the friction-wheel is not contaminated with oil or grease, otherwise its efficiency will be impaired. (e) Use Underground. — If the lamp is extinguished when in use, no immediate attempt should be made to relight it until the products of combustion in the lamp have been cleared. A period of about one minute or so should suffice for their clearance, which can be assisted by gently swinging the lamp or by blowing through the ventilation holes. The relighter should not be operated whilst the lamp is full of products of combustion from an extinct flame. On no account should a lamp which may have been damaged be relighted without careful examination. The glass should be particularly carefully examined before the relighting device is used if the lamp has been accidentally dropped or knocked.
|
|||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||