Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

8th October 1938, Page: 101, Column: 1

Mine Supports

Notes from Dr. Hogan's Address

Referring again to the paper on "Laboratory Investigations on Supports" which Dr. M. A. Hogan presonted to the Mining Teachers' Conference, some of the points listed may suitably be culled. The most important properties of supports are the strength and deformation under load, whilst the manner in which the supports are set, i.e., the contact area and the nature of the floor and roof strata with which they are in contact, exerts an important influence on the supporting power, and must not be lest sight of. In the laboratory investigations the supports have been subjected to the same type of loading under similar conditions to those underground.

Props. — The experiments on timber props drew attention to two points which are deserving of emphasis: The serious reduction in the strength of timber due to moisture, and the considerable variations in strength shown by props of the same nominal size. For example, a 6-inch diameter prop of Baltic timber 6 feet long would have a breaking strength of 45 tons when dry as compared with 30 tons when wet. It was found that Baltic props were the most uniform and the strongest, but that carefully prepared home-grown timber was practically as strong.

Ordinary timber props shorten very little before breaking (about ¼ inch in 6 feet) and so must be considered as rigid. To enable them to yield under load one end is sometimes tapered. When this is properly done the narrow end "burrs," enabling the props to shorten under a gradually increasing load.

Steel props may be divided into two groups: rigid and yielding. The majority of the steel props used in Britain are of the rigid type because British mining practice aims at reducing the subsidence of the roof at the coal face to a minimum so that fracturing of the roof strata may he prevented as far as possible.

The commonest type of steel prop is of girder or joist section; props of tubular section are also used. The tubular section is theoretically attractive because it gives the best distribution of the metal, but the thickness of the metal is so small that the tubes are liable to local damage which cannot readily be repaired. To overcome this difficulty tubular props are commonly filled with timber which prevents the local deformation but without adding to the strength. In one proprietary form of prop the tube is filled with sand under pressure and closed by welding. Props are usually made of mild steel and bend when overloaded. A bent steel prop will continue to develop a useful resistance, unlike a timber prop which is useless once failure has occurred.

Lids. — Lids are used to increase the hearing area between the prop and the roof and to facilitate the setting of the prop. When used with timber props the lid further serves as a cushion to protect the prop from being split by inequalities in the roof. The width of a timber lid should he equal or slightly greater than the width of the prop, and the length should be not less than the diameter of the prop plus twice the thickness of the lid — or, according to another rule, three times the diameter of the prop.

Rectangular or slightly tapered lids of sawn timber give the best results — the taper assists the setting and withdrawal. Lids made from old props are objectionable because they yield too much, and small irregularly-shaped pieces of timber are bad because they lead to high contact stresses against the roof and eccentric loading of the prop.

In a timber lid the grain lies horizontally and at right angles to the pressure, consequently the timber squeezes relatively easily. The thickness of the lid really controls the amount of compression of the face supports.

Corrugated steel lids are sometimes used. A corrugated steel lid should not be set in direct contact with a prop because, if both are of steel, setting will be difficult and there will be a danger of the prop slipping out.

Bars. — Bars enable the roof to be supported between the props, and by a system of bars at right angles it is possible to reduce the size of the unsupported areas, thus reducing the risk of small falls. Bars may he either of steel or timber, but the ductility of steel is of special importance in this application because steel bars continue to afford support when bent, whereas timber bars break when the deflection exceeds a moderate amount and have no further supporting value. The more rigid the bar, the less likely is it to be deformed and require restraightening. It must be remembered that the bar also functions as a lid to increase the bearing areas of the props at either end, and that the prop loads serve to fix the ends.

Cogs and Chocks. — Cogs and chocks are square or rectangular structures built up of pieces of timber or steel used to support the roof.

Steel chocks differ from those of timber in having a smaller amount of compression whilst retaining the large contact area against roof and floor. Chocks are very difficult to withdraw and special provision must be made for this when the chock is set. In the past this was done either by building the chock on a heap of soft dirt which could easily be picked away or by putting in one round timber to he knocked out. Both these expedients had the disadvantage of reducing the resistance of the chock. Recently special release devices, depending on the separation of folding wedges or similar elements, have been introduced which overcome this difficulty.

Cogs being made of round timber have a very low initial resistance due to the small area of contact between the sticks. The initial resistance may be improved by flattening the contacts. Unless a cog is tightly filled with packing material its strength is very low; for example, a 3½ feet square unfilled cog of 4-inch diameter props failed under a load of 21 tons with 22.7 per cent. compression. Unfilled cogs with only two props to a layer are unstable, but this can be remedied by increasing the number of props in a layer. Filling a cog produces a great increase in the strength and stability of a cog, the better the filling material the better the strength.

Packs. — The packs form the permanent supports on which the full pressure of the overlying strata eventually has to be carried, and underground experience has proved the value of efficient packing in improving the roof conditions at the face.

Where the only material available for packing is a soft shale which cannot be built into walls special means must be employed, such as bags or wire netting, If the material is filled into bags a satisfactory pack wall can be built, and although the initial resistance is less than that of a stone wall the bags enable the pack to build up a gradually increasing resistance. Cogs can be built with bags and these develop a resistance which is considerably better than that of an unfilled timber cog. It is important that the bags should only be loosely filled so that the wall can be built without having voids, e.g., with hessian bags 14 x 33 inches the thickness should not exceed 4.5 inches. Similar results can be obtained when a pack wall is built in layers about 1 foot thick, each layer being tied back by wire netting. The action of the netting and the bags is essentially the same — to provide a horizontal bond to tie in the outermost layers to the body of the pack and enable them to resist being spilt out.

Roadway Supports. — Experiments have been made on the effect of different types of connection between the bar and props of a timber setting. This is commonly done by notching the bar and various forms of notch exist. The Welsh notch was found to be the best type for resisting side loads, but equally good results were given by a steel knee shoe.

The strength of steel arches is considerably greater than that of timber supports of the sizes commonly employed and experiments on arches for a roadway 8 feet wide gave the following results : horseshoe 22.5 tons, straight-sided 27.1 tons, and splay-legged 35.3 tons. These arches were of 4 x 2 and 2½ inches rail section tested under vertical loads without any lining. Lagging the arches so as to prevent failure by buckling in the plane of the walls produces a marked rise in strength.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Hogan, A. M., Dr.      Whos Who Page


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print