8th October 1938, Page: 99, Column: 1
Coal Measure Rocks
In his address on "Coal Measure Rocks and the Problem of
Roof Control" before the Mining Teachers' Conference, to which
reference has already been made in this journal, Dr. D. W. Phillips
said that a study has been made of a large number of rocks from
different coalfields and it has been found that standard geological
terms will fully describe any of these rocks. They fall
into the five groups Sandstones, Siltstones, Mudstones, Shales
and Clays. Appropriate adjectives will, however, have to be
used to describe any constitutional or structural features. In
this way we can have massive calcareous sandstone, bedded
argillaceous sandstone, flaggy micaceous sandstone, banded or
non-banded siltstone, arenaceous shales, arenaceous clays,
carbonaceous clays, etc.
Strength Properties. — It can now be stated as the result of work
in compression and torsion that when the rocks are subjected to
stress the resultant strain is made up of: (1) Immediate strain,
i.e., the strain produced directly a load is applied; (2) Time
strain, i.e., a strain produced with time after a load is applied.
Further, the time strain can be divided into : (a) Elastic time
strain, which is that part of the strain produced by loading, that
is recovered gradually with time after the load is removed.
(b) Plastic time strain, which is that part of the strain that is not
recoverable with time after the load is removed.
In rock samples subjected to compression, the strain occurring
in both the longitudinal and lateral directions was measured
simultaneously and pronounced time strains have been observed
in some rocks in both directions during loading and unloading.
The rate and amount of the time strains increase as the stress
increases, but at each stress the rate diminishes with time. At
low stresses the time strain ceases completely, sometimes in the
first few minutes, but at high stresses both the longitudinal and
lateral time strains will proceed for days at varying rates. In
some rocks, more particularly sandstones, the rates and amounts
of the longitudinal time strains are always greater than those of
the lateral time strains, but above certain stresses, in shales, the
rates and amounts of the lateral time strains are the greater.
Pronounced time strains have been responsible for the loads
on some rocks specimens being decreased. This phenomenon
is dependent upon the manner in which the rocks are loaded.
In the particular tests the plates of the compression testing
machine were fixed in position after the loads were applied. The
lateral time strains developed to such an extent in some tests that
in order to maintain the same load on the specimens the plates
of the machine would have to he free to move towards each other;
being unable to do this then the specimen became relieved of lead.
The counterpart of this phenomenon has been observed in
the North of England investigations. Bords can be relieved of
load by driving ahead of them what are called advance relief
bords. An advanced relief bord is driven the width of a pillar
ahead of the two bords on each side and the roof is then caused
to collapse. The two adjacent bords driven later experience
much less pressure than bords driven in the ordinary way. It
is evident that the collapse of the shale roof in the pressure relict
bord enables the immediate shale bed above the pillars to expand
laterally towards the collapsed roadway. In order to maintain
the original vertical pressure on the roof the whole section of
strata to the surface would have to subside a little. This is not
likely to occur at the boundary of whole workings in bord and
pillar, therefore the vertical pressure acting on the roof in regions
surrounding the pressure relief bord will become less. The
relieved bords are at a distance of 18 yards on each side of the
pressure relief bord, but how far beyond this distance relief is
afforded is not known. In consequence of this relief a region of
increased pressure is to be expected at some distance beyond the
relieved bords, but so far this region has not been discovered.
Elastic Modulus in Compression. — The determination of the
elastic modulus for a material exhibiting time strain is not a
simple matter. In so much as this modulus is a function of the
relation of stress to strain and that the strain is again a function
of time, then different rates of loading will result in different
modulus values. However, the more rigid a rock, the less is the
strain, and an idea of the relative rigidities of rocks can be obtained
by comparing the stress-strain relation for the immediate application
of the loads, the time strain being allowed to develop at each
load, or for the stress-strain relation after equal intervals of time
on each load.
The elastic moduli for sandstones, siltstones and shales vary
between 1 x 106 lb. per square inch and 3 x 105 lb. per
square
inch; the values for coal are between 0.3 x 106 lb. per square
inch and 0.6 x 106 lb. per square inch. The elastic moduli in
compression is a measure of the vertical resiliencies of these rocks,
i.e., their tendency to expand in a vertical direction owing to
their being compressed.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Phillips, D. W., Dr. | | | |