|
10th September 1938, Page: 65, Column: 1 Notes On May ExaminationsReport of Central ExaminersThe Question Papers set at this Examination (May, 1938) have been published in pamphlet form and are obtainable (2s. net) from H.M. Stationery Office. Below we give the text of questions set at the May examinations (plans not reproduced), each question being followed by the Central Examiners' comments on the work generally of the candidates. The "comments" are in italics. Winning and Working (1st Class). (1) Lay out with the aid of sketches a small district of bord and pillar or pillar and stall workings showing the roads and pillars and giving the important dimensions assuming a depth of 400 yards. State the estimated output for the district and the number of men of the various classes you would employ. Under what conditions would you adopt this method of working? (50) Answers were fairly good on The whole, but estimated outputs were inclined to be on the optimistic side. Some candidates omitted to state the classes of workmen employed other than actual colliers. (2) Where men are conveyed to and from their work in a steep main incline what method of haulage would you adopt and what special precautions would you take to reduce the risk of accidents? (40) Direct or main rope haulage was the favourite system adopted. The chief fault was the emission to describe or sketch the type of carriage used. This was generally referred to as a "special" carriage, which is too vague. A number did not slate that the seats on the carriages in steep inclines should be so arranged that the men can sit comfortably. (3) Discuss the following fuels under the heads of carbon content, moisture and volatile matter: (a) Lignite (b) cannel; (c) anthracite; (d) bituminous coal. Mention places in Great Britain where these fuels are found. (40) Moderately well answered, although the localities were wrong in many cases, especially as regards lignite, which some candidates appeared to confuse with peat. (4) Sketch and describe any type of modern longwall coal-cutting machine with which you are familiar. State the conditions you consider most suitable for its use. (40) Good answers. A few omitted to make a sketch and some descriptions lacked detail. (5) Describe in detail, with the aid of sketches, how you would form a concrete bricking curb in a 20-ft. finished diameter shaft. State what provision you would make for dealing with any water from the unbricked length of shaft above. (40) This question was not well answered, and in the majority of cases showed a lack of knowledge, which candidates attempted to hide by vagueness. As an example of this, one candidate stated that the curb would be formed in the "usual way." Candidates should try to visit modern sinkings and obtain practical knowledge first hand. (6) Describe with sketches, giving approximate dimensions, how you would proceed to construct an engine-house in solid strata of a heavy nature and in close proximity to main intake haulage road. The engine-house is to be suitable for a 150-h.p. electrically-driven endless rope haulage gear. (40) This was a practical question and the answers for the most part were disappointing. A large number failed to state by what method they would carry out the excavation work, and merely stated that they would "get the ground out." Only a few mentioned that special permission would be needed for shot-firing in close proximity to a main intake haulage road, and it was the exception for a candidate to mention the steps that he would take to secure the main road itself before commencing to excavate the engine-house. Some candidates made provision below floor level for wheel races, but not a single one made any provision for a rope race. (7) The percentage of large coal being made in working a seam is found to be too low. To what would you ascribe such a state of affairs, and what suggestions would you make to reduce the proportion of small coal? (40) Generally speaking, the answers were good, but a few omitted to mention explosives. Ventilation (1st Class). (1) On the plan . . . show how you would arrange the distribution of the air-currents, using the signs and colours given in the General Regulations. Sheets to be shown thus J. (50) The plan, one of retreating pillar and stall work, brought out some points of difference. Most of the candidates gave reasonable arrangements, but many placed the upcast shaft on the dip side of the downcast, while the majority placed it to the rise as expected. There was, in nearly half the answers, a tendency to allow the working faces to be ventilated with a minor part of the air-current, the larger volume being sent round the pillars, while the reverse was preferable, with the smaller air-current skirting the pillars to keep them clear. (2) Make a list of the gases usually met with in mine atmospheres, giving their composition, properties and weight. State which may be dangerous, and what is the proportion in which each becomes dangerous ? (30) Most candidates were able to give a satisfactory list, but too many included hydrogen, argon, and others, which are not usually met with. Specific gravity was often omitted. (3) What types of water-gauge are used in mine ventilation? Illustrate in detail how the pressures are measured, and how recorded. What is known as a "high water-gauge," and what are its effects ? (30) The types were well known and described. High water-gauges and their effects were dealt with adequately. In some cases the levels of the water in the two legs were reversed. (4) What do you understand by "natural ventilation"? How is it induced ? State its effects on other methods of generating a current. What course is considered of importance in dealing with the air-current in the faces and adjoining workings, and under what conditions is it most marked? (30) Well answered, except that the marked effect of steep workings was only dealt with in a few cases. (5) In an ordinary ventilating installation, what is gained by the use of an "evasee" ? Give calculations of the advantage in an assumed case. Show, with sketch, how this gain can be attained in the instance of an installation of a screw fan. (30) Well answered by about half the candidates, but the calculation of the gain proved too much for the others. Most were able to show how the same object was attained in the case of a screw fan. (6) How would you ascertain if the ventilation in any given district or split was sufficient or satisfactory ? How is the question of the ventilation of the faces affected by leakage along intake airways? State how this can best be prevented; and give sketches and descriptions of the construction and erection of a permanent stopping, alongside the main intake. What other additional arrangements are desirable to prevent leakage? (30) This was a favourite question and well answered. In most cases the masonry walls of the permanent stoppings were much too thick. (7) Two adjacent shafts, 20 feet diameter, are being sunk to a depth of 600 yards, in coal measures. State what plant you would install for ventilation, and in particular give details of the conveyance of the air in the shafts. (30) Many candidates did not appreciate the size of the job, and the necessity of getting separate duplicate plants — each to act also as a partial standby to the other — was often not advocated. Explosions, Etc. (1st Class). (1) Reproduce the sketch . . . in your answer book. What is the water pressure in lb. per square inch at the extreme dip of the old workings, at point A? Sketch and describe how you would approach the old workings to tap and drain the water off. (30) Some of the reproductions of this simple sketch were very crude. Very few candidates gave the correct figure for the water pressure at a given point, taking the surface level instead of the top of the shaft for the total head. The majority of the candidates suggested approaching the old workings from a point immediately below, and mode no provision for a safety dam or pipes to convey the water. Few candidates suggested approaching the old workings along the line of strike or level course, such procedure, where possible, being much safer than on the full rise of 1 in 4. (2) What alteration would you expect to find in the composition of the air in the return airway from a district of a mine in which spontaneous heating has just commenced ? What are the limits of inflammability of methane — (a) in pure air; (b) with 20 per cent, of CO2 present; (c) with 25 per cent, of CO2 present? (25) Some candidates said there would be a reduction in the quantity of the return air as a result of the heating. Many gave satisfactory answers to the first part of the question, but the answers to the second part were varied, and many were incorrect. (3) On a roadway along which a large quantity of water normally flows from disused workings to pumps at the pit bottom, a very large fall occurs which blocks the roadway and holds back the bulk of the water. As the water accumulates behind the fallen debris there is danger of it suddenly breaking through in much greater quantity than the pumps can deal with. How would you deal with the situation? (25) Many candidates assumed that the roadway could be built off permanently, and suggested nothing but the construction of a dam. Candidates did not appreciate the urgency of securing the roadway close to the fall, end endeavouring to make a way over the top for a pipe to convey the water. The withdrawal of men was not suggested, although in a case of this kind it should have been considered. (4) How would you proceed to investigate the cause and point of origin of an explosion in a mine ? What are the effects generally produced: (a) by an explosion of firedamp without coal dust, and (b) by an explosion of coal dust without firedamp? (25) The answers to the first part of the question were disappointing. The answers to the second part of the question were generally good. (5) Sketch a section of a seam of coal which you suspect is liable to spontaneous heating. Make a sketch plan of a district of workings suitable for the seam, the coal to be cut by machines, with conveyors on the faces and gate-roads. Assume an inclination of 1 in 5. (25) By two neat sketches with suitable references, a complete answer could have been given to this question. The sketches were poor and incomplete. (6) In the advancing longwall workings of a mine which is dusty and yields firedamp, spontaneous heating has occurred which necessitates the closing of part of the workings by stoppings in the roadways. What matters would you take into consideration when deciding upon the number, position and construction of the stoppings? Give a sketch with your answer. (25) Many candidates would place the stoppings quite close to the heating, which is often a dangerous procedure. Others described stoppings which would take considerable time to erect, not realising the importance of time in these cases. Machinery (1st Class). (1) A small 3-phase transformer is to be used to provide 125-volt current from a 440-volt supply for working a drilling machine, using a flexible cable. Describe the switchgear that should be installed to work and protect the transformer and the motor of the drilling machine and to render the plant safe for use. Assume that explosive gas may be present. (28) Many answers showed a good working knowledge of the switch. gear Remote control was often mentioned. A weakness was to omit necessary interlocking. Some answers made provision for too much switchgear. (2) Describe a 3-phase transformer suitable for about 100 K.V.A. to give a secondary pressure of, say, 400 volts from a primary pressure of, say, 2,200 volts. What are convenient connections for the primary windings and for the secondary windings? What are the usual fittings and accessories that are applied to a transformer ? (28) This question was not well answered. A single-phase transformer was often described, and candidates did not realise how three single-phase transformers become combined in one apparatus making a three-phase arrangement. Descriptions of the actual design of transformers were weak and diagrams often showed impossible electrical connections. The list of fittings applied to a transformer was usually incomplete. Instead of mentioning oil level gauge, drain cock, cable bores, lifting eyes, specification plate, earthing terminal, a number of candidates referred to switch-gear. (3) It is decided to improve the power factor of an electric plant whose load is 240 kilowatts at 0.6 lagging power factor by adding a synchronous motor whose input of power is 210 kilowatts. What must be the leading power factor of the motor to raise the overall power factor to 0.9 lagging? (28) Other questions in the electrical section were more in favour, and only a few of those who attempted this question obtained the correct answer. The calculation was simple — it was a matter of knowing how to set to work. (4) Describe in detail the work of cleaning a Lancashire boiler from the time when it ceases to supply steam to the time When it recommences to supply steam. (28) This question was answered by nearly all. It was easy to write something on it, and marks were won by attention to details. (5) A multi-stage centrifugal, or turbine, pump has 6 impellers 10 inches diameter, with a width of opening at the rim of 0.65 Inch. The suction branch is 5-inch bore. The delivery branch is 4-Inch bore. The pump runs at 1,440 revolutions per minute. What are approximately the best conditions of head and of rate of flow of water? If such a pump fails to deliver water (through a fault not connected with the driving motor) where would you look for possible causes? (28) Many candidates knew methods of arriving at the suitable head and rate of flow for the conditions given. Others stated that a suitable head for any impeller was, say, 100 feet. As causes for the failure of a pump to deliver water, most candidates correctly would look to the suction for leakage of air or chokage. Troubles within the pump were not often referred to. (6) In connection with steel-wire winding ropes: (a) By what process should the steel be made? (b) What is the common range of strength of wires in tons per square inch? (c) By what processes is the strength of steel wires attained ? (d) What tests of wire may lie made to show its suitability for use in a winding rope ? (28) The process for making the steel was seldom known. A statement that it should be by the acid open hearth process would suffice, but some candidates stated that crucible steel is used. In dealing with the attainment of strength in steel wires, the process of drawing was often referred to, but the process of annealing less often. As tests for wire, tensional, torsional, bending and wrapping tests were often correctly referred to, but a number of candidates did not know the details of the making of these tests. (7) You are called upon to examine thoroughly a steam winding plant within the engine-house to see whether it is in efficient and safe working order. To what matters would you direct your attention and what would you do? (28) This question was attempted by nearly all candidates. There was always some merit in the answers, but a number omitted to mention indicator diagrams for showing up the work of the steam cylinders. (8) A steel shaft is 4 feet long and 7 inches diameter. At one end there is a solid half coupling 18 inches diameter, and 2 inches thick in the flange. At the other end there is a separate cast steel half coupling, keyed on. This half coupling is 20 inches diameter, and 3 inches thick in the flange. The coupling flanges are plain. Make a side elevation of this assembly to a scale of 1½ in. = 1 ft., with dimensions, choosing your dimensions where not given. (38) A common mistake here was to show the solid half coupling machined down square at the back as if the coupling were a flat disc. A good fillet would certainly be formed here. It was also a common mistake to show the separate half coupling as a disc 3 inches thick, whereas there would certainly be a boss formed to increase the length of bearing between the coupling and the shaft. The half coupling was shown secured by a key. In many cases the key had a gib head and was driven from the back of the coupling towards the end of the shaft. This is, or course, incorrect. [To be continued.]
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||