7th May 1938, Page: 340, Column: 1
Drilling Operations Abroad
By Richard Hall, Assoc.I.M.E.
From paper on "Notes on Drilling Operations Abroad," read at
the April meeting of the Associates and Students' Section of the
North of England Institute of Mining and Mechanical Engineers.
Drilling operations take great variety of form but may be
divided roughly under three heads : (a) percussive and rotary,
(b) percussive, (c) rotary. Under (a) may be classed the "hammer
and tap," compressed air hammer drills used extensively in coal
mines, quarries and most rock excavations, also the heavier
water-fed drills used in metal mines. In the percussive class of
drilling I will make mention later of the Keystone Rig used for
well-drilling, the valuating of alluvial deposits of gold and tin.
In some countries this form of churn drilling is also used for boring
in stratified deposits. Typical examples of rotary drilling are
the diamond drill, the Burnside boring apparatus, and the familiar
"coal auger" and stand used for so long in this and other countries
by coal hewers.
In percussive and rotary drilling I will pass over "hammer and
tap" as being of little interest here and deal with water-fed drills.
Primarily, water-fed drills were introduced into metal mines with
a view to combat the incidence of silicosis. They did this
successfully as far as the drillers were concerned, but their introduction
did much more. Drilling speeds in levelling, stoping,
drifting, sinking and raising were increased because the clearing
of the drill-hole with a strong flush of water also had a cooling
effect on the cutting edge of the drill steel.
The quantity of water necessary to drill-out a full round of
holes, say in a 12' by 6' 6" stone drift, with water-fed drills is not
very great. It is usual in some metal mines to have water
containers charged and sent in to the face Where drilling is to take
place.
For cleaning and dust allaying devices, water under a pressure
of anything from 20 lb. to 150 lb. is used. The water can be
brought to the drill in any convenient way, and if a pressure due
to source of supply cannot be obtained it can be kept in a tank
for each drilling machine, and a pressure equal to the working
pressure of the drill can be got by admitting compressed air to
the tank. The water passes from the tank through a flexible
hose to the back-head of the drill, two valves being used, one for
regulating the amount of water introduced to the drill, and the
other for turning on and off the supply. The water passes through
the hack-head plug and water tube into the shank of the drill
steel, where air from the drill mingles with it, and both pass on
through the drill steel to the bottom of the drill-hole. Water-fed
drills are similar to dry drills.
Rotation is transmitted to the drill steel in the following
manner: The chuck holding the drill steel carries a nut with
grooves which fit into the flutings on the front end of the hammer,
and thus the latter rotates the chuck and the steel. The hammer
in turn is rotated by the rifle bar, which fits into a rifle nut in the
back end of the hammer. A ratchet and pawl arrangement allows
rotation in only one direction.
Drilling holes vertically downwards and to the dip with water
fed drills is an easy matter when a strong flush of water and air
is available, providing that the drill operator knows his job. He
will usually see to it that his steel is properly collared and shanked,
and that the gauge of his steel bits is of correct size for following
each other. He will have a good eye for "shouldering" of the
steel-bit points. He will always include in his equipment a ring
key for extracting difficult steel, also a blow-pipe capable of attachment
to the compressed air flexible hose. The blow-pipe is curved
at the operating end so that when air-flushing takes place the
operator can stand clear of the ejected borings.
There is a wide application for this class of equipment in colliery
work, especially in stone-drifts, the proving of faults, and in
raising and sinking. The usual practice in collieries is to utilise
the lighter hammer drills used in top and bottom canches for the
heavier class of work, and it is even possible to find solid
twist drill steel being employed for putting in holes to the dip
in the presence of water — it is not unknown for "Sylvesters"
having to pull out solid twist drill steel.
In a big colliery it would be an economy to have at least one
big hammer drill, water-fed, with column, also a stoping drill,
water-fed, for exploratory and development purposes.
Diamond Drilling (Rotary). — It is not my intention to go into
the details of this form of drilling, except to emphasise the need
for a very efficient pump to ensure an adequate force of water to
circulate under the diamond crown, and on its upward journey
to still have sufficient force to carry up with it all borings. It
might also be necessary to mention the advisability of allowing
space enough in between the diamonds to ensure this result.
With diameter holes no sludging of the hole is required, and even
the smallest particles of chipping are recovered by passing the
return water through a fine strainer at the mouth of the hole before
using it again. A prospecting pan is very useful to collect borings
as they come out of the hole; they can thus be washed and
sampled whilst drilling is continued. When a change in strata
is encountered, an experienced driller will readily note the "feel"
of the rods and will also note the rate of "feed."
Keystone Drills.
This form of power-drill, known as the Keystone Rig (percussive)
is being used extensively throughout the world in valuating
auriferous alluvials. It is also used in valuating tin alluvial
deposits. Blanket deposits which, in many cases, cover square
miles of flats, are prospected by means of Keystone drills and
sometimes in the case of gold "leads" close drilling with them
is resorted to, Coal seams occurring at moderate depths have
also been proved by these drills,
Usually, in boring sub-aqueous alluvials, the size of casing is
6" diameter with a 7¼" shoe provided with a sharp outside
cutting
edges Lengths of casing are usually 5' and 10'. A very
substantial driving head is fitted on to the casing to withstand
the heavy battering of a 5 cwt. drill-bit, which has a 2' drop or
stroke and delivers between 70 and 80 blows per minute. The
casing is knocked down 2' to 5' per drop. Every care is taken
to see that each length of casing is butting with the adjacent
length. A careful record of the depths driven to is kept in a log
book.
The rig itself is mounted on four wheels, the two front ones
being of smaller diameter than the rear. It may sometimes have
to travel over very difficult ground — sand dunes, through dense
bush, or in river beds. This is often accomplished with its own
power, using either the sand-line or the spudding rope. Both
spudding drum and sand-line drum are belt-driven from the
engine. The spudding drum needs to be of very strong construction.
The sand-line drum is of lighter construction, carrying a
steel cable of 3/8" diameter for operating the sand pump.
There is a separate lever for the spudding drum and for the
sand-line drum. They are never worked together. In each
case, the levers that operate them engage with a friction clutch
in one extreme position and apply a brake in the other extreme
position. When the levers are in the intermediate position the
drums are free to move. Each of the drums is driven from a
countershaft which, in turn, is belt-driven from the engine.
The spudding rope passes from the drum around three sheaves.
Two of the sheaves are attached to a "walking-beam," and the
third at the derrick head. The "walking-beam" is hinged to
each side of the drill at the rear end and motion is given to the
fore end by connecting rods suitably arranged to the driving
mechanism to give an up and down motion. The spudding rope
with a 5 cwt. drill attached is thereby operated at one end and
held fast at the drum end. The "walking-beam" crankshaft is
gear-driven from the drill countershaft.
The drilling tool is 4" diameter and about 10' long. At two places
in the iron stem the section is forged square for the fitment of
driving clamps. The weight of the drilling tool with clamps
attached is about 600 lb. The number of blows per minute
ranges 60-80.
The arrangement of jacks and beams should be very carefully
done. It is usual to have the necessary measurements permanently
marked on the beams and jacks to facilitate assembling.
The steel grips are much quicker than wood clamps — but with
a heavy pull they can damage the casing, and sometimes it is
necessary to use both.
A simple but efficient means of proving a coal seam which had
been disturbed by a 35' downthrow fault: 1" diameter steam piping
(no special boring rods were available), cut and threaded into
3' lengths, a hollow spiral cutting bit giving 2" diameter — a
swivel
connection for the attachment of ¾" diameter flexible hose —
hand
pump connected and fixed on top of a tub of water. A wood
clamp with handles was used to give rotation.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Hall, Richard | | | |